Service Manuals, User Guides, Schematic Diagrams or docs for : Keithley 70xx 7063_901_01A
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download 7063_901_01A documenatation <<
Text preview - extract from the document
Model 7063 RF Switch Card
Instruction Manual
Contains Operating and Servicing Information
Document Number: 7063-901-01 Rev. A
WARRANTY
Keithley Instmmcnts, Inc. warrants this product to bc free from defects in material and
workmanship for a period of 1 year from date of shipment.
Keithley Instruments, Inc. warrants the following items for 90 days from the dale of
shipment: probes, cables, rechargeable batteries, diskettes, and documentation.
During the warranty period, we will, at our option, either repair or replace any product
that proves to be defectivc.
To exercise this warranty. write or call your local Keithley representative. or contact
Keithley headquarters in Cleveland, Ohio. You will be given prompt assistance and
return instructions. Send the product, transportation prepaid, to the indicated service
facility. Repairs will be made and the product returned, transportation prepaid. Repaired
or replaced products are warranted for the balance of the original warranty period, or at
least 90 days.
LIMITATION OF WARRANTY
This warranty does not apply to defects resulting from product modification without
Keithley's express written consent, or misuse of any product or part. This warranty also
doer not apply to fuses, software, non-rechargeable batteries, damage from battery leak-
age, or problems arising from normal wear or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR USE. THE REMEDIES PROVIDED HEREIN
ARE BUYER'S SOLE AND EXCLUSIVE REMEDIES.
NEITHER KEITHLEY INSTRUMENTS, INC. NOR ANY OF ITS EMPLOYEES
SHALL BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF ITS INSTRU-
MENTS AND SOFTWARE EVEN IF KEITHLEY INSTRUMENTS, INC., HAS
BEEN ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES.
SUCH EXCLUDED DAMAGES SHALL INCLUDE, BUT ARE NOT LIMITED TO:
COSTS OF REMOVAL AND INSTALLATION, LOSSES SUSTAINED AS THE
RESULT OF INJURY TO ANY PERSON, OR DAMAGE TO PROPERTY.
Model 7063 RF Switch Card
Instruction Manual
Safety Precautions
The following safety precautions should be observed before using this product and any asso-
ciated insrmmentation. Although some instmments and accessories would normally be used
with non-hazardous voltages, there are situations where hazardous conditions may be present.
This product is intended for use by qualified personnel who recognize shock hazards and are
familiar with the safety precautions required to avoid possible injury. Read the operating ins
formation carefully before using the product.
The types of product users are:
Responsible body is the individual or group responsible for the use and maintenance of
equipment, for ensuring that the equipment is operaled within its specifications and operat-
ing limits, and for ensuring that operators are adequately trained.
Operators use the product for its intended function. They must be trained in electrical safety
procedures and proper use of the insmnncnt. They must be protected from electric shock and
contact with hazardous live circuits.
Maintenance personnel perform routine procedures on the product to keep it operating. for
example, setting the line voltage or replacing consumable materials. Maintenance procedures
are described in the manual. The procedures explicitly state if the operator may perform them.
Otherwise, they should be performed only by service personnel.
Service personnet are trained to work on live circuits, and perform safe installations and re-
pairs of products. Only properly trained sewice personnel may perform installation and ser.
vice procedures.
Exercise extreme caution when a shock hazard is present. Lethal voltage may be present on
cable connector jacks or test fixtures. The American NationaJ Standards Institute (ANSI)
states that a shock hazard exists when voltage levels greater than 30" RMS, 42.0 peak, or
60VDC are present. A good safety practice is to expect that hazardous voltage is present
in any unknown circuit before measuring.
Users of this product must be protected from electric shock at all times. The responsible body
must ensure that WWFare prevented accessand/or insulated from every connection point. In some
cases, connections must be exposed to potential human contact. Product users in these circum-
stances must be trained to protect themselves from the risk of elecnic shock. If the circuit is ca-
pable of operating at or above 1wO volts, no conductive part of the circuit may be exposed.
As described in the lntemational Electrotechnical Commission (IEC) Standard IEC 664, dig-
ital multimeter measuring circuits (e.g., Keitbley Models 175A, 199. 2000, 2001. 2002, and
2010) are installation Category II. All other instruments' signal terminals are Installation Cat-
egory 1 and must not be connected to mains.
Do not connect switching cards directly to unlimited power circuits. `Ibey are intended to be
used with impedance limited sources. NEVER connect switching cards directly to AC mains.
When connecting sources to switching cards, install protective devices to limit fault current
and voltage to the card.
Before operating an instrument, make sure the line cord is connected to a properly grounded
power receptacle. Inspect the connecting cables, test leads, and jumpers for possible wear,
cracks, or breaks before each we.
For maximum safety, do not touch the product, test cables. or any alher insbunents while pow-
er is applied to the circuit under test. ALWAYS remove power from the entire test system and
discharge any capacitors before: connecting or disconnecting cables or jumpers, installing or
removing switching cards, or making internal changes, such as installing or removingjumpers.
Do not touch any object that could provide a current path to the common side of the circuit
under test or power line (earth) ground. Always make measurements with dry hands while
standing on a dry, insulated surface capable of withstanding the voltage being measured.
The instrument and accessories most be used in accordance with its specifications and op-
erating instructions or the safety of the equipment may be impaired.
Do not exceed the maximum signal levels of the insuuments and accessoties. as defined in
the specifications and operating information. and as shown on the instrument or test fixture
panels, or switching card.
When fuses arc used in a product. replace with same type and rating for continued protection
against fire hazard.
Chassis connections most only be used as shield connections for measuring circuits, NOT as
safety earth ground connections.
If you are using a test fixture, keep the lid closed while power is applied to the device under
test. Safe operation requires the use of a lid interlock.
1fa @ scow is present, connect it to safety earth ground using !he wire recommended in
tic user documenmtion.
The/& sy mblo on an insb'ument indicates that the user should refer to the operating in-
structions located in the manual.
The A symbol on an instmmcnt shows that it can sowce or measure loo0 volts or more, in-
cluding the combined effect of normal and common mode voltages. Use standard safety precau-
tions to avoid personal contact with these voltages.
The WARNING heading in a manual explains dangers that might result in personal injury or
death. Always read the associated information very carefully before performing the indicated
procedure.
The CAUTION heading in a manual explains hazards that could damage the instrumem.
Such damage may invalidate the warranty.
instrumentation and accessories shall not be connected to humans.
Before performing any maintenance, disconnect the line cord and all test cables.
To maintain protection from electric shock and fire, replacement components in mains cir-
cuits, including the power uansfomxr, test leads, and input jacks, most be purchased from
Keithley Instruments. Standard fuses, with applicable national safety approvals, may be used
if the rating and type are the same. Other components that are not safety related may be pur-
chased from other suppliers as long as they are equivalent to the original component. (Note
that selected parts should be purchased only through Keithley Insnuments to maintain acco-
racy and functionality of the product.) If you are unstxe about the applicability of a replace-
ment component, call a Keithley lnsouments office for information.
To clean an instrument, use a damp cloth or mild, water based cleaner. Clean the exterior
of the instrument only. Do not apply cleaner directly to the insounent or allow liquids to
enter or spill on the instrument. Products that consist of a circuit board with no case 01chas-
sis (e.g., data acquisition board for installation into a computer) should never require clean-
ing if handled according to instructions. If the board becomes contaminated and operation
is affected, the board should be returned to the factory for proper cleaning/servicing.
RC".
2m
SPECIFICATIONS
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo