Service Manuals, User Guides, Schematic Diagrams or docs for : Tektronix TM 515 parts
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download TM 515 parts documenatation <<
Text preview - extract from the document
TM 9-6695-24-34P
This is a reprint including Change 1
DEPARTMENT OF THE ARMY TECHNICAL MANUAL
DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE
REPAIR PARTS AND SPECIAL TOOLS LIST
FOR
TMDERS MAINFRAME, TEKTRONIX MODEL TM 515
(NSN 6695-01-074-7953)
Current as of 5 December 1979
Headquarters, Department of the Army, Washington, DC
8 January 1980
REPORTING OF ERRORS
You can help improve this publication by calling attention
to errors and by recommending improvements and stating
your reasons for the recommendations. Your letter or DA
Form 2028, Recommended Changes to Publications,
should be mailed directly to Commander, US Army Missile
Command, ATTN: DRSMI-MFM, Redstone Arsenal, AL
35809. A reply will be furnished directly to you.
Paragraph Page
SECTION 1. INTRODUCTION
Scope ....................................................................................................... 1 1
General ................................................................................................... 2 1
Explanation of columns ............................................................................ 3 1
Special information .................................................................................. 4 5
How to locate repair parts ........................................................................ 5 5
Abbreviations ........................................................................................... 6 6
II. REPAIR PARTS LIST .............................................................................. 9
Functional Group Model Part
group title No. No.
6692 TMDERS Mainframe TM 515 MIS30526/ITY3
III. NATIONAL STOCK NUMBER AND PART
NUMBER INDEX...................................................................................... 11
Change 1 i
TM 9-6695-245-34P
Section 1. INTRODUCTION
1. Scope. This manual lists spares and repair parts that are required for maintenance of the TMDERS Mainframe,
Tektronix Model TM 515. It authorizes the requisitioning and issue of spares and repair parts as indicated by the source
and maintenance codes.
2. General. This repair parts and special tools list (RPSTL) is divided into the following sections:
a. Section 1. Introduction.
b. Section II. Repair Parts List. A list of spares and repair parts authorized for use in the performance of
maintenance. The list also includes parts which must be removed for replacement of the authorized parts. Parts
lists are composed of functional groups in numeric sequence, with the parts in each group listed in figure and item number
sequence. Bulk materials are listed in National Stock Number (NSN) sequence.
c. Section III. NSN and Part Number Index. A list, in National Item Identification Number (NIIN) sequence, of all
NSN's appearing in the listings, followed by a list in alphanumeric sequence of all part numbers appearing in the listings.
NSN's and part numbers are cross-referenced to each illustration figure and item number appearance
3. Explanation of Columns
a. Illustration. This column is divided as follows:
(1) Figure Number . Indicates the figure number of the illustration on which the item is shown.
(2) Item Number. The number used to identify item called out in the illustration.
b. Source, Maintenance, and Recoverability (SMR) Codes.
(1) Source Code. Source codes indicate the manner of acquiring support items for maintenance, repair, or
overhaul of end items. Source codes are entered in the first and second positions of the Uniform SMR Code format as
follows:
Code Definition
PA - Item procured and stocked for anticipated or known usage.
PB - Item procured and stocked for insurance purpose because essentiality dictates that a minimum quantity be
available in the supply system.
PC - Item procured and stocked and which otherwise would be coded PA except that it is deteriorative in nature.
PD - Support item, excluding support equipment, procured for initial issue or outfitting and stocked only for subsequent
or additional initial issues or outfittings. Not subject to automatic replenishment.
PE - Support equipment procured and stocked for initial issue or outfitting to specified maintenance repair activities.
PF - Support equipment which will not be stocked but which will be centrally procured on demand.
Change 1 1
TM 9-6695-245-34P
PG - Item procured and stocked to provide for sustained support for the life of the equipment. It is applied to an item
peculiar to the equipment which, because of probable discontinuance or shutdown of production facilities, would
prove uneconomical to reproduce at a later time.
KD - An item of a depot overhaul/repair kit and not purchased separately. Depot kit defined as a kit that provides items
required at the time of overhaul or repair.
KF - An item of a maintenance kit and not purchased separately. Maintenance kit defined as a kit that provides an item
that can be replaced at organizational or intermediate levels of maintenance.
KB - Item included in both a depot overhaul/repair kit and a maintenance kit.
MO - Item to be manufactured or fabricated at organizational level.
MF - Item to be manufactured or fabricated at the direct support maintenance level.
MH - Item to be manufactured or fabricated at the general support maintenance level.
MD - Item to be manufactured or fabricated at the depot maintenance level.
AO - Item to be assembled at organizational level.
AF - Item to be assembled at direct support maintenance level.
AH - Item to be assembled at general support maintenance level.
AD - Item to be assembled at depot maintenance level.
XA - Item is not procured or stocked because the requirements for the item will result in the replacement of the next
higher assembly.
XB - Item is not procured or stocked. If not available through salvage, requisition.
XC - Installation drawing, diagram, instruction sheet, field service drawing, that is identified by manufacturer's part
number.
XD - A support item that is not stocked. When required, item will be procured through normal supply channels.
NOTE
Cannibalization or salvage may be used as a source of supply for any items coded above except
those coded XA and aircraft support items as restricted by AR 700-42.
(2) Maintenance Code. Maintenance codes are assigned to indicate the levels of maintenance authorized to USE
and REPAIR support items. The maintenance codes are entered in the third and fourth positions of the Uniform SMR Code
format as follows:
(a) The maintenance code entered in the third position will indicate the lowest maintenance level authorized to
remove, replace, and use the support item. The maintenance code entered in the third position will indicate one of the
following levels of maintenance:
2
TM 9-6695-245-34P
Code Application/Explanation
C - Crew or operator maintenance performed within organizational maintenance.
O - Support item is removed, replaced, used at the organizational level.
F - Support item is removed, replaced, used at the direct support level.
H - Support item is removed, replaced, used at the general support level.
D - Support items that are removed replaced, used at depot, mobile depot, or specialized repair activity only.
(b) The maintenance code entered in the fourth position indicates whether the item is to be repaired and identifies
the lowest maintenance level with the capability to perform complete repair (i.e., all authorized maintenance functions). This
position will contain one of the following maintenance codes:
Code Application/Explanation
O - The lowest maintenance level capable of complete repair of the support item is the organizational level.
F - The lowest maintenance level capable of complete repair of the support item is the direct support level.
H - The lowest maintenance level capable of complete repair of the support item is the general support level.
D - The lowest maintenance level capable of complete repair of the support item is the depot level.
L - Repair restricted to (enter applicable designated specialized repair activity), Specialized Repair Activity.
Z - Nonreparable. No repair is authorized.
B - No repair is authorized. The item may be reconditioned by adjusting, lubricating, etc., at the user level. No parts or
special tools are procured for the maintenance of this item.
(3) Recoverability Code. .Recoverability codes are assigned to support items to indicate the disposition action on
unserviceable items. The recoverability code is entered in the fifth position of the Uniform SMR Code format as follows:
Recoverability
Codes Definition
Z - Nonreparable item. When unserviceable, condemn and dispose at the level indicated in position 3.
O - Reparable item. When uneconomically reparable , condemn and dispose at organizational level.
F - Reparable item. When uneconomically reparable, condemn and dispose at the direct support level.
3
TM 9-6695-245-34P
H - Reparable item. When uneconomically reparable, condemn and dispose at the general support level.
D - Reparable item. When beyond lower level repair capability, return to depot. Condemnation and disposal not
authorized below depot level.
L - Reparable item. Repair, condemnation, and disposal not authorized below depot/specialized repair activity level.
A - Item requires special handling or condemnation procedures because of specific reasons (i.e., precious metal
content, high dollar value, critical material or hazardous material). Refer to appropriate manuals/directives for
specific instructions.
c. National Stock Number (NSN). Indicates the NSN assigned to the item and which will be used for requisitioning.
d. Part Number. Indicates the primary number used by the manufacturer (individual, company, firm, corporation,
or Government activity), which controls the design and characteristics of the item by means of its engineering drawings,
specifications, standards, and inspection requirements to identify an item or range of items.
NOTE
When a stock numbered item is requisitioned, the item received may have a different part number
than the part being replaced.
e. Federal Supply Code for Manufacturer (FSCM). The FSCM is a 5-digit numeric code listed in SB 708-42 which is
used to identify the manufacturer, distributor, or Government agency, etc.
f. Description. Indicates the Federal item name and, if required, a minimum description to identify the item. The
physical security classification of the item is indicated by the parenthetical entry (insert applicable physical security
classification abbreviation, e.g., Phy Sec C1 (C)-Confidential, Phy Sec Cl (S)-Secret, Phy Sec C1 (T)-Top Secret). Items
that are included in kits and sets are listed below the name of the kit or set with the quantity of each item in the kit or set
indicated in the quantity incorporated in unit column. When the part to be used differs between serial numbers of the same
model, the effective serial numbers are shown as the last line of the description. In the Special Tools List, the initial basis
of issue (BOI) appears as the last line in the entry for each special tool, special Test, Measurement, and Diagnostic
Equipment (TMDE), and other special support equipment. When density of equipments supported exceeds density
spread indicated in the BOI, the total authorization is increased accordingly.
g. Unit of Measure (U/M). Indicates the standard of the basic quantity of the listed item as used in performing the
actual maintenance function. This measure is expressed by a two-character alphabetical abbreviation (e.g., ea, in, pr, etc).
When the unit of measure differs from the unit of issue, the lowest unit of issue that will satisfy the required units of
measure will be requisitioned.
4
TM 9-6695-245-34P
h. Quantity Incorporated in Unit. Indicates the quantity of the item used in the breakout shown on the illustration
figure, which is prepared for a functional group, subfunctional group, or an assembly. A "V" appearing in this column in lieu
of quantity indicates that no specific quantity is applicable (e.g., shims, spacers, etc).
4. Special Information
a. Repair parts for components of standards sets which can be identified as existing in the supply system will be
requisitioned through normal supply channels from the appropriate supply commodity manager.
b. Repair parts for components of standards sets which cannot be identified as to proper supply source will be
requisitioned from USAMICOM, using routing identifier B64 and furnishing as a minimum, the following as exception data.
(1) Component stock number of the individual end item to be repaired.
(2) Component manufacturer's equipment model number and serial number.
(3) The equipment manufacturer's stock number as listed in the appropriate manual for the desired repair part.
(4) The repair part reference, designation, circuit reference, circuit symbol schematic designation, or reference
number as listed in the manufacturer's manual.
(5) The technical specification of the repair part as contained in the appropriate manufacturer's manual.
(6) The title and date of the manufacturer's manual from which the information in paragraphs a, b(3), (4), and (5)
above was taken.
NOTE
Repair parts should not be requisitioned for plug-in boards identified in the plug-in board exchange program, except by the
depot designated to perform the repair. Repair of calibration set components, with plug-in board assemblies or
subassemblies designated as program exchange replacements with a recoverability code of L, will be accomplished by
replacing the plug-in board.
c. The plug-in board exchange program functions are as follows:
(1) Requisitioning instructions for initial issue plug-in boards will be provided since new instrument boards
are included in the program.
(2) As a plug-in board covered by the program fails, a replacement will be requisitioned. Requisitions will be submitted
to Commander, US Army Missile Command, B64, Redstone Arsenal, AL 35809.
(3) Simultaneously with c(2) above, the defective board being replaced will be shipped by certified mail, return receipt
requested, to the following address:
Transportation Officer
Anniston Army Depot
M/F Field Service Stock
Anniston, AL 36201
When requisitioning a replacement board, the turn-in document number of the replaced board shall be cited on the
requisition.
5. How to Locate Repair Parts
a. When NSN or reference number is unknown:
(1) First. Using the table of contents, determine the assembly (functional group) within the repair part belongs.
5
TM 9-6695-245-34P
(2) Second. Using the repair parts listing, find the functional group to which the repair part belongs and locate the
item by description.
b. When NSN or reference number is known:
(1) First. Using the index of NSN's and reference numbers, find the pertinent NSN or reference number. This
index is in ascending NSN cross-referenced to the illustration figure number and item number.
(2) Second. Using the repair parts listing, find the figure and item number, and locate the figure and item number in
the repair parts list.
6. Abbreviations. The abbreviations listed below may appear in this RPSTL:
AC ------------------ alternating current FLG ----------flange
ACC ---------------- accordance FREQ -------frequency
ACCUR ------------ accuracy FSCM -------Federal supply code for manufacturers
AL ------------------- aluminum FT----------- foot
AMP ---------------- ampere GC -----------gigacycles
ASSY --------------- assembly GEN--------- generator
ASTM -------------- American Standard GHZ ---------gigahertz
for Testing Materiel GPM ---------gallons per minute
ATTEN ------------- attenuation GRAD------- graduation
AWG --------------- American Wire H ------------ high
Gage HD----------- head
BAN ---------------- banana HYDR -------hydraulic
BLK------------------ black HZ---------- hertz
BR ------------- ---- brass ID ------------inside diameter
C ------------ -------- centigrade, calibration IN ----------- inch
cycles per second INCL --------inclusive
CAL ----------------- calibrate K ------------- thousand (prefix)
CAP---------- ------- capacitance KC ---------- kilocycles
CD ---------- ------- code KG---------- kilograms
CER ---------- ------ ceramic KHZ --------- kilohertz
COAX ------- ------ coaxial -- KMHZ ------ thousand megahertz
COMP-------- ----- - composition KV ----------- kilovolts
COND ------------- - conductor LAB---------- laboratory
CONN ------- ------ connector LB ----------- pounds
CONS--------------- consisting LG----------- length
CONT---------- ----- continual LT ------------light
COP ---------- ------ copper
COR-------------------- corrosion
CPS ------------------ cycles per second
CU -------------------- cubic
CUR ----------------- current
CYL ------------------ cylinder
DB ----------------- - decibel
DBL------------------ double
DC ------------------- direct current
DEG --------------- - degree
DET--------------- -- detector
DIA --------------- -- diameter
DIM --------------- - - dimension
DIV -------------- - -- division
DPDT ----------- - -- double pole double throw
DPL----------- ------ deployment
ELEC --------------- electrical
EQUIPM------ ---- - equipment
F -------------------- - Fahrenheit
FED --------- ------ - Federal
FIN ------------------ finish
6
TM 9-6695-245-34P
M --------------------- thousand RPM -----------------------revolutions per
MA------------------- milliampere minute
MAX ---------------- maximum S ---------------------------single
MC ----------------- megacycles SEC -------------------- seconds
MFD ---------------- millifarads SECT------------------- section
MFR ---------------- manufacturer SERR------------------ serrated
MG ----------------- milligrams SHK -------------------- shank
MHZ ---------------- megahertz SNG -------------------- single
MIN ----------------- minimum, minutes SPEC ------------------- specification
ML ------------------ milliliters SPL-------------------- special
MM------------------- millimeters SQ ---------------------- square
MOD ---------------- modified STD ------------------ standard
MSEC -------------- milliseconds STGT------------------ straight
MTL ---------------- material SW --------------------- switch
MV ------------------ millivolts SWR ------------------- standing wave
MW ---------------- milliwatts ratio
NBS---------------- National Bureau SYS ------------------- system
Standards TEL ------------------ telescopic
NEG----------------- negative TERM ----------------- terminal
NO------------------ number THD------------------- thread
NOM--------------- nominal THERM --------------- thermometer
NPT---------------- National Pipe THK ------------------ thick
Thread TSTR ----------------- tester
NSN --------------- National stock U ---------------------- unit
number UF ------------------ microfarads
OA ------------------ overall UHF -------------------- ultra high frequency
OD ----------------- outside diameter V ---------------------- volts
OPER ------------- operating VAC ------------------ volts alternating
OZ ----------------- ounce current, vacuum
PCS -------------- pieces VDC ------------------ volts direct current
PCT -------------- percent VHF ------------------ very high frequency
PF ---------------- picofarads VSWR ----------------- voltage standing
PK -------------------- peck wave ratio
PLTD --------------- plated W --------------------- watts, with, width
PN ------------------- part number WT------------------- weight
POS------------ ----- positive
PP------------------- peak-to-peak
PSI ------------------ pounds per square
inch
PWR------------------ power
REF------------------- reference
REP------------------ repetition
REQ ---------------- required
REQMTS----------- requirements
RES------------------ resistance
RF -------------------- radio frequency
RG------------- ------ range
RH -------------------- right hand
RL-------------------- reel
RM ------------------- rack mounted
RMS ----------------- root mean square
ROT ----------------- rotating
7 (8 blank)
SECTION II. REPAIR PARTS LIST
(1) (2) (3) (4) (5) (6) (7) (8)
DESCRIPTION QTY
NATIONAL INC
ILLUSTRATI SMR STOCK PART IN
ON CODE NUMBER FSCM NUMBER USUABLE ON CODE U/M UNI
T
(a) (b) GROUP 6692
FIG ITEM MAINFRAME, TMDERS
NO. NO. TM 515
MIS30526/1TY3
80009 18876
1 10 PAFZZ 5910-00-943-9192 283-0022-00 80009 CAPACITOR.FIXED CER ........................ EA 1
1 20 PAFZZ 5910-00-577-1346 DA149-00108 71590 CAPACITOR,FIXEC.CER. EA 12
1 30 PAFZZ 5910-01-022-3075 290-0637-00 80009 CAPACITOR.FIXEC.ELE. ........................ EA 4
EA
1 40 PAFZZ 5910-00-467-1548 60O10444 56289 CAPACITOR,FIXED,ELE . ........................ 2
EA
1 50 PAFZZ 5910-00-43E-3382 152-0040-00 80009 CAPACITOR .................... ........................ EA 2
1 60 PAFZZ 6695-01-08L-1050 670-4021-00 80009 CIRCUIT CARD. ASSY .... ........................ EA 1
1 70 PAFZZ 6695-01-086-1051 670-4021-01 0009 CIRCUIT CARD ASSY ..... ........................ EA 1
1 80 PAFZZ 6695-01-018-1052 670-4364-00 80009 CIRCUIT CARD ASSY ..... ........................ EA 1
1 90 PAFZZ 6695-01-086-1053 670-4364-01 00009 CIRCUIT CARD ASSEMBLY..................... EA 1
1 100 PAFZZ 6695-01-086-1054 670-4022-00 80009 CIRCUIT CAPRD ASSY... ........................ EA 1
1 110 PAFZZ 6695-01-086-1055 670-4022-01 80009 CIRCUIT CARD ASSY ..... ........................ EA 1
1 120 PAFZZ 6695-0l-086-1056 670-4220-00 80009 CIRCUIT CARD ASSY ..... ........................ EA 2
130 PAFZZ 6695-01-086-1057 670-4220-01 80009 CIRCUIT CARD ASSY ..... ........................ EA
1 1
EA
1 140 PAFZZ 6695-01-086-1058 670-5204-00 00009 CIRCUIT CARD ASSY ..... ........................ 2
EA
1 150 PAFZZ 5935-00-599-8548 131-1078-00 80009 CONNECTOR, RECEPTACLE ................. EA 5
1 160 PAFZZ 4140-00-726-9755 WR2AI 82877 FAN.TUOEAXIAL ............. ........................ EA 2
1 170 PAFZZ 4140-00-917-3914 AO-86312 82877 FAN,TUEAIAL .................. ........................ EA 1
1 180 PAFZZ 5920-00-83S-2318 MDA3 71400 FUSE,CARTRIDGE159-0005-00 FSCM .. EA 1
1 190 PAFZZ 5920-00-284-7079 AOC21/2 71400 FUSE,CARTRIDGE159-O126-00 FSCM .. EA 2
1 200 PAFZZ 5905-00-138-4927 RCR42G102JS 81349 RESISTOR.FIXED,COMP ........................ EA 5
1 210 PAFZZ 5905-00-494-4622 RCR32G182JS 81349 RESISTOR,FIXED,COMP ........................ EA 10
1 220 PAFZZ 5905-00-283-7474 G81025 01121 RESISTOR.FIXEO COMP EA 3
81349 RESISTOR,FIXED,COMP ........................ EA
1 230 PAFZZ 5905-00-110-0992 RCR32G51IJS 3
EA
1 240 PAFZZ 5961-00-131-1197 152-0274-00 80009 SEMICONDUCTOR DEVICE .................... EA 2
1 250 PAFZZ 5930-00-377-9979 260-0907-00 800C9 SWITCH.THERMOSTATIC ....................... EA 2
1 260 PAFZZ 5950-01-064-1163 120-1031-00 00009 TRANSFORMER.POWER. ....................... EA 1
1 270 PPFZZ 5961-00-370-1271 151-0373-00 80009 TRANSISTOR .................. ........................ EA 5
1 280 PAFZZ 5961-00-551-0637 151-0436-00 S0009 TRANSISTOR .................. ........................ EA 5
EA
9 (10 blank)
Change 1
TM 9-6695-245-34P
SECTION III. NATIONAL STOCK NUMBER AND PART NUMBER INDEX
FIGURE ITEM FIGURE ITEM
STOCK NUMBER NO. NO. STOCK NUMBER NO. NO.
5905-00-11-C992 1 23C 920-00-839-2318 1 180
5961-00-131-1197 1 24C 414000-0917-3914 1 170
5905-00-138-4927 1 200 5910-0 943-9192 1 10
5905-00-283-1474 1 22C 5913-1-322-3C75 1 30
5920-00-284-7C79 1 19C 5950-01-064-1163 1 260
5961-00-370-1271 1 27C 6695-01-086-1050 1 60
5930-00-377-5579 1 250 6695-01-086-1051 1 70
5910-00-436-3382 1 50 6695-01-086-1052 1 80
5910-00-467-1548 1 40 6695-01-386-1053 1 90
5905-00-494-4622 1 210 6695-01-086-1054 1 100
5961-00-551-C637 1 28C 6695-01-086-1055 1 110
5913-00-577-1346 1 2C 6695-o1-0e6-1C56 1 120
5935-00-599-8548 1 15C 6695-01-086-1057 1 130
4140-00-726-5755 1 16C 6695-01-086-1C58 1 140
PART FIG. ITEM PART FIG.ITEM
NUMBER FSCMNO. NO. NUMBER FSCM NO. NO.
AGC 2- 1/2 71400 1190 152-0274-00 80009 1 240
A0-86312 82877 1 170 260-3907-00 80009 1 250
DA149-001CB 71590 1 20 283-0022-00 80009 1 10
G81025 01121 1 220 290-0637-00 80009 1 30
MDA3 71400 1 180 670-4021-00 80000 1 63
RCc32G182JS 81349 1 210 670-4021-01 80009 1 70
RCR32G51IJS 81349 1 230 670-4022-00 80009 1 100
RCR42G1O2JS 81349 1 200 673-4022-01 80009 1 110
WR2A1 82877 1 160 670-4220-00 80009 1 120
120-1031-CC 80009 1 260 670-4220-01 80009 1 130
131-1378-CC 80009 1 150 670-4364-00 80009 1 80
151-0373-OC 80009 1 270 670-4364-01 80009 1 90
151-0436-0C 80009 1 280 670-5204-00 80009 1 140
152-0040-00 80009 1 50 68010444 56289 1 40
11
TM 9-6695-245-34P
By Order of the Secretary of the Army:
E. C. MEYER
General, United States Army
Official: Chief of Staff
J. C. PENNINGTON
Major General, United States Army
The Adjutant General
Distribution:
To be distributed in accordance with DA Form 12-34A, requirements for Calibration Procedures
Publications.
U. S. GOVERNMENT PRINTING OFFICE: 1981-546-033/2981
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo