Service Manuals, User Guides, Schematic Diagrams or docs for : panasonic Audio CR16 Mechanisme CR16 Assembly

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.




Image preview - the first page of the document
CR16 Assembly


>> Download CR16 Assembly documenatation <<

Text preview - extract from the document
CD Changer CR16 Mechanism                                                                      AVC-NBG


Assembly / Adjustment Procedure
Any further updates or electrical faults can be accessed on Kbase within Technical Support(search on CR16)

1*                                                                                    * Denotes parts
                                                                                      that did not
                                                                                      require removal
                                                                                      in Disassembly so
                                                                                      may already be
                                                                                      fitted




2*




3*




4*




5*
                                                                                          Phase
                                                                                          Mark




                                                                              Phase
                                                                              Mark




                                                                                      Assembly Page 1/8
6


                                                              This part is critical
                                               Move side plate forward a fraction
                                               when fitting. When it clicks into
                                               position, move side plate back
                                               again. Arrowed tooth must locate
                                               in first slot of side plate as shown




7*




8*




9*




     Hold above gear in position whilst fitting gear below
10




                                                                                      Assembly Page 2/8
11*




      Refit screw if it was originally fitted, part number XTBS26+8J
      Be careful not to over-tighten-this gear is not used in mech operation, only used for the jig tool
12*




13*




14




15




                                                Align the long tooth
                                                on the rack (see left)
                                                with the half tooth on
                                                the gear (see right)




                                                                                             Assembly Page 3/8
16
                             Fit then screw in




17




18*
                   Insert this way round
                   NB Not necessary to
                   remove this "lifter"
                   gear in disassembly




19




      Phase Adj.



                   With the left side
                   plate far back,
                   this gear should turn
                   anticlockwise
                   but only slightly clockwise


20*




                             Assembly Page 4/8
21
                                           Slot in as shown on far left,
                                           then rotate until phase
                                           aligned. Large gear will then
                                           catch the "pip" of the lifter
                              Phase Adj.   below the "lemon" gear.




22*




23*




24*




25


      The white rack indicated
      by the red arrows, is shown
      in the forward position
      from 26 onwards. This
      is due to us changing the
      point of moving side plate
      forwards to simplify repair
26    process. This will be
      rectified once more photos
      have been taken. This
      part will naturally move
      forward when side plate is
      wound forward in section 34



                                                     Assembly Page 5/8
27




28




29*




30*




31*




32            Align as
              shown
              on left




      Assembly Page 6/8
32




                                                                                        Screw

                                                                                         Hook




33 At this point bring the side plate forward using the jig tool until level with front of chassis




34




35 Traverse in down position-lever at rear should be as far back as possible on left side. (See red arrow)
   Traverse should slot in left side first-may find it easier to use jig tool to move side plate forward further
   (33). Slow down as reaching end of travel as complete re-alignment required if it clicks out of position!
   After slotting in traverse, side plate should be moved back level to front of chassis using jig tool




                                                                                   *Marking to the right*
                                                                                   Important that this gear
                                                                                   does NOT engage with
                                                                                   drive rack just above.
                                                                        Pull white
                                                                        rack slightly as shown on left until
                                                                        it clicks into position.
                                                                                               Assembly Page 7/8
     Insert tray drive loading gear in to position and then insert metal shaft down the centre
37




                                                                                  Top lugs on the tray drive
                                                                                  loading gear should align
                                                                                  horizontally with front of
38                                                                                mech and trays should be
                                                                                  as far forward as possible
                                                                                  before slotting down.
                                                                                  The white gear in the centre
                                                                                  of the black plate should
                                                                                  move clockwise slightly
                                                                                  when the trays are inserted-
                                                                                  if it moves anti-clockwise
                                                                                  adjust the tray loading drive
                                                                                  gear slightly and re-attempt.
39                                                                                Turning tray drive loading
                                                                                  gear 180 degrees may help

                                                                                  Slide all trays back manually
                                                                                  together until front of trays
                                                                                  align with front of mech
                                                                                  then insert lock lever.




40




                                                                                             We recommend
                                                                                             fitting top cover
41                                                                                           before powering
                                                                                             up as this provides
                                                                                             additional support
                                                                                             to the side plate.

                                                                                             You are now ready
                                                                                             to operate. Please
                                                                                             use additional info
                                                                                             on CD Test Mode
                                                                                             to check operation.

                                                                                             Assembly Page 8/8



◦ Jabse Service Manual Search 2020 ◦ Jabse Pravopis ◦ Other service manual resources online : FixyaeServiceinfo