Service Manuals, User Guides, Schematic Diagrams or docs for : panasonic Audio SB-WA101 hfe_panasonic_sb-wa101pp_service
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download hfe_panasonic_sb-wa101pp_service documenatation <<
Text preview - extract from the document
ORDER NO. MD0603091C1
A6
Active Subwoofer System
SB-WA101PP
Colour
(S)... Silver Type
Specification
n SPEAKER SECTION Power consumption in input 1W
Type 1 way 1 speaker system standby condition:
Bass-reflex type
Speaker Note :
Woofer 17 cm (6-3/4") cone type x 1 Specifications are subject to change without notice.
Sound pressure level 81 dB/W (1.0 m) Mass and dimensions are approximate.
Frequency range (with amp) 32 Hz-300 Hz (at -16 dB)
38 Hz-240 Hz (at -10 dB) nSpeaker System : SB-TP100PP- Front Speaker : SB-FS100PP-S
S
n AMPLIFIER SECTION Surround Speaker : SB-FS100PP-
S
Output power 100 W (6 ) (THD 0.9%)
Center Speaker : SB-PC100E-S
Input sensitivity / Input Impedance 300 mV/33 k (RCA jack)
Subwoofer : SB-WA101PP-S
Phase switching NORMAL/REVERSE
Low pass filter 50 Hz-200 Hz Variable
n GENERAL
Power supply AC 120 V, 60Hz
Power consumption 168 W
Dimensions (W x H x D) 162 x 457 x 420 mm
(6-13/32" x 18" x 16-9/16")
Mass 11.3 kg (23.8 lb.) SB-TP100PP-S consists of:
SB-FS100PP-S (x 4), SB-PC100E-S (x 1) and SB-WA101PP-S (x 1)
SB-WA101PP
CONTENTS
Page Page
1 Safety Precautions 3 6.7. Disassembly of Transformer P.C.B. 11
1.1. General Guidelines 3 6.8. Disassembly of Level control P.C.B. 11
1.2. Before Repair and Adjustment 4 7 Connection of the Speaker wiring 13
1.3. Protection Circuitry 4 8 Wiring Connection Diagram 14
2 Prevention of Electro Static Discharge (ESD) to 9 Block Diagram 15
Electrostatically Sensitive (ES) Devices 5 10 Notes of Schematic Diagram 17
3 Warning 6 11 Schematic Diagram 19
3.1. Service caution based on legal restrictions 6 11.1. Power Circuit, Level Control Circuit, Transformer Circuit
4 Accessory 7 and LED Circuit 19
5 Connection of the Speaker Cables 7 12 Printed Circuit Board 21
6 Assembling and Disassembling 8 12.1. Power P.C.B., Level Control P.C.B., Transformer P.C.B.
6.1. Caution 8 and LED P.C.B. 21
6.2. Disassembly flow chart 8 13 Illustration of IC's, Transistors and Diodes 23
6.3. Disassembly of Stand ornament 9 14 Exploded view 24
6.4. Disassembly of Power amplifier unit 9 14.1. Cabinet Parts Location 24
6.5. Disassembly of Woofer speaker 10 14.2. Packaging 25
6.6. Disassembly of Power P.C.B. 10 15 Replacement Parts List 26
2
SB-WA101PP
1 Safety Precautions
1.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, ensure that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
3. After servicing, check for leakage current checks to prevent from being exposed to shock hazards.
(This "Safety Precaution" is applied only in U.S.A.)
1. Before servicing, unplug the power cord to prevent an electric shock.
2. When replacing parts, use only manufacturer's recommended components for safety.
3. Check the condition of the power cord. Replace if wear or damage is evident.
4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.
5. Before returning the serviced equipment to the customer, be sure to make the following insulation resistance test to prevent the
customer from being exposed to a shock hazard.
1.1.1. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
2. Using an ohmmeter measure the resistance value, between the jumpered AC plug and each exposed metallic cabinet part on
the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 1M and 5.2.
When the exposed metal does not have a return path to the chassis, the reading must be .
Figure 1
1.1.2. Leakage Current Hot Check (See Figure 1)
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a 1.5k, 10 watts resistor, in parallel with a 0.15◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo