Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Infiniti M45 Y34 2003-2004 Approved M45-Y34-2004 acc
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download acc documenatation <<
Text preview - extract from the document
ACCELERATOR CONTROL SYSTEM
B ENGINE
A
ACCELERATOR CONTROL SYSTEM
SECTION ACC ACC
C
D
E
CONTENTS
ACCELERATOR CONTROL SYSTEM ..................... 2 . SERVICE DATA AND SPECIFICATIONS (SDS) ....... 4 . F
Removal and Installation ......................................... 2
. Standard and Limit ................................................... 4
.
REMOVAL ............................................................ 2
. Tightening Torque .................................................... 4
.
INSTALLATION .................................................... 3
. G
INSPECTION AFTER INSTALLATION ................ 3 .
H
I
J
K
L
M
Revision: 2004 October ACC-1 2004 M45
ACCELERATOR CONTROL SYSTEM
ACCELERATOR CONTROL SYSTEM PFP:18005
Removal and Installation ABS000NC
SBIA0328E
1. Accelerator wire 2. Accelerator wire bracket 3. Seal rubber
4. Accelerator wire bracket 5. Pedal bracket 6. E-ring
7. Bush 8. Stopper 9. Accelerator pedal
Accelerator wire should be adjusted when removing and replacing any parts of the Accelerator Control Sys-
tem, shown in the illustration.
REMOVAL
1. Remove engine cover. Refer to EM-12, "ENGINE ROOM
COVER" .
2. Loosen lock nut, and remove accelerator wire from throttle
drum.
3. Remove accelerator wire from accelerator pedal.
4. Remove accelerator wire bracket bolt and nut, and pull acceler-
ator wire into vehicle interior.
5. Remove accelerator pedal bracket nuts, then remove accelera-
tor pedal and bracket assembly.
SBIA0330E
Revision: 2004 October ACC-2 2004 M45
ACCELERATOR CONTROL SYSTEM
INSTALLATION
q Install in the reverse order of removal procedures, paying extra attention to the items below. A
CAUTION:
q Do not leave scratches, twist or bends on accelerator wire cores.
q Do not apply lubricant to inside accelerator wire.
ACC
q Check if accelerator pedal is free from contact with other parts, and releases smoothly.
q For ASCD wire adjustment, refer to ACS-30, "ASCD Wire Adjustment" .
C
Adjusting Accelerator Wire
1. Loosen lock nut and adjusting nut.
2. Tighten accelerator adjusting nut until throttle drum starts to move. D
3. From that position, turn back adjusting nut 1.5 to 2 turns.
4. Tighten lock nut to specified torque holding adjusting nut.
E
INSPECTION AFTER INSTALLATION
q Check if throttle drum opens fully when accelerator pedal is fully depressed to the floor, and operates
smoothly in all process.
F
q Check if throttle drum returns to idle position when pedal is released.
q Check if the ASCD wire is not pulling the throttle drum.
G
H
I
J
K
L
M
Revision: 2004 October ACC-3 2004 M45
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS) PFP:00030
Standard and Limit ABS000ND
Turning back of accelerator wire adjusting nut 1.5 - 2 turns (From position throttle drum just starts to move)
Tightening Torque ABS000NE
Unit: N◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo