Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan 300ZX 1984-1985,1988,1990,1994-1996 Approved 1988 Body

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document
Body

>> Download Body documenatation <<

Text preview - extract from the document

BOD1

SECTION BF
CONTENTS
GENERAL SERVICING (Including all clip 81fastener for 231) ..................... BF- 2
BODY END AND DOOR (Including "Opener" and "Power window".
And also including wiring diagram) .......................................... BF- 7
INSTRUMENT (Including "Center console") .................................... BF-16
SEAT (Including "Power seat" and wiring diagram)............................... BF-17
SEAT BELT ............................................................. BF-28
INTERIOR AND EXTERIOR ............................................... BF-29
WINDSHIELD AND WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BF-36
T-BAR ROOF ............................................................ BF-41
MIRROR (Including wiring diagram) .......................................... BF-42
REAR AIR SPOILER ..................................................... BF-43
REAR COMBINATION LAMP .............................................. BF44
BODY ALIGNMENT - Engine compartment & Underbody
(Including the actual dimensions between the points and the coordinates of the points) .. BF-45

For theft warning system, refer t o EL section.
* For seat belts, refer to MA section.
Method of reading electrical diagram in BF section is basically the same as in the E L section.
So refer to "HOW TO READ DIAGRAM" in'EL section.
For power supply routing, refer to "POWER SUPPLY" in E L section.
Black box internal circuits in BF section are a summary of actual circuit.
Use only for studying the operation.
"Remarks" and "Connections" in electrical diagram show the terminal meaning and actual
electrical flow.
For connector Nos. in wiring diagrams in this section, refer to Harness Layout in EL section.
GENERAL SERVICING
Precautions

When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent
scratches.
Handle trim, molding, instruments, grille, etc. carefully during removing or installation. Be careful not to
soil or damage them.
Apply sealing compound where necessary while installing parts.
When applying sealing compound, be careful that' the sealing compound does not protrude from parts.
When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust pre-
vention measures.

Clip and Fastener

Clips and fasteners in BF section correspond to the following numbers and symbols.

No. I Svmbol I Shaoe Removal & Installation

Removal:
R m w e by bnding up with
a flat-bladed xrmdriver.

SBF0928 SBF1098 SEFO940

Removal:
Remove wahfbtb,bded
screwdrivers or pliers.

SBFllOB SBFlllB SBFllZB
R.WWWl:
Remove with fbtbladad
screwdrivers or pliers.

SBF358B SBF359B SBF36OB

Removal:
Tilt clip as indioaled by
arrow, than draw out.

SBF1418 SB F 1 4 2 8 SBF143B

BF-2
GENERAL SERVICING
Clip and Fastener (Cont'd)

Symbol Shape Removal & Installation
~~~

Removal:
Remove with flm-bbded
srawdrivars or pliers.

SBFOB9B SBFO900 SBFO9lB

Removal:
Remove by bendiw up with
flat-bladed screwdrivers

SB F 366 0 SBF3660 SB F 367 B

Removal:
Remove by bndinp up with
a flat-bladed rcrawdriver.

SBF564B SSF6660 SBF6668

Removal:

3
w
SBF605C SBF606C SBF625C

Removal:
Flat-bladed

SBF636C F SBF637C SBF638C

BF-3
GENERAL SERVICING

NO. Symbol Shape Removal & Installation

T T Removal:

8 SSF1388 $? SSF1398
S e r m out with a Phillips
screwdriver.

U
t
b
T T
@

@ 58F3748 i
ts SSF3750
SBFl408

& SBF103B SSF1048 CEF1470

SSF6538 off the clip. SSF9148

Flat-bladed
screwdriver
Molding

BF-4
GENERAL SERVICING
Clip and Fastener (Cont'd)

No. Symbol %ape Removal & Installation

Clip4
Flatbladed
screw driver

\Clip4 (Grommet1

1
SBFO32C ' SBF034C

Removal:

SBF411B SEF4126
I

Removal:
Flat-bladed screwdriver
rFinirher

SBF652B

BF-5
GENERAL SERVICING
Clip and Fastener (Cont'd)

No. I Symbol Shape Removal & Installation

RemoveI:
Holder ponion of clip must ba
spread out to remove rod.

S8F1068 S8F1468

Ramoval:
Holder portion of clip must b.
spread out to remove rod.

S8F76BB SBF7708

BF-6
BODY END AND DOOR
rn When removing and installing hood or back door, place a cloth or other padding on hood or back door
corners to avoid scratching vehicle body.
rn When removing clip or fastener, refer to CLIP & FASTENER.
Apply sealing compound where necessary when installing parts.

Front End
Hood adjustment: Adjust at hinge portion.
rn Hood lock adjustment: After adjusting, check hood lock control operation. Apply a coat of grease to
hood locks engaging mechanism.
rn Hood opener: Do not attempt to bend cable forcibly. Doing so increases effort required to unlock hood.
Bumper fascia: It is made of plastic, so do not use excessive force and take care t o keep oil away from it.
rn When adjusting or removing/installing hood or rernoving/installing hood switch, check theft warning sys-
tem operation.
WARNING:
a. Be careful not t o scratch hood stay when installing hood. A scratched stay may cause gas leakage.
b. The contents of the hood stay and bumper shock absorber are under pressure. Do not take apart,
puncture, apply heat or allow fire near it.

Bumper shock absorber inspection
1. Check shock absorber for oil leakage, cracks or deformation.
2. Function of shock absorber;
(1) Place vehicle in front of a wall.
Apply parking brake and place tire stoppers securely.
(2) Place a jack between bumper and wall; jack is positioned square with Jmper directly line with
shock absorber to be checked.
(3) Apply pressure to compress shock absorber a t least 10.0 rnm (0.394 in).
Use a jack with capacity of more than 600 kg (1,323 Ib).
(4) Make sure bumper returns to its original position when jack is retracted. Replace if necessary.
CAUTION:
It is not recommended to confirm proper installation by driving into walls or other barriers as this could
cause personal injury or damage to the vehicle.
When replacing shock absorbers, make sure they are of the same type and rating, and manufactured by the
same maker.

BF-7
BODY END AND DOOR
Front End (Cont'd)

After hood lock adjustment, adjust bumper rubber. 12.1 . 2 . 7 . 1 5 . 2 0 )
When securing hood lock, ensure it doer not tilt. Striker
must be positioned at the center of hqod primary lock.
After adjustment, ensure that hood primary and second-
11.3- 1.6.9.12)
ary lock operate properly.
,- Hood d j u r t m m t

Secondary latch hooking length jumper height: "X"
Secondary latch I 2 seater I 2 + 2 seater
Bumper fascia
Turbocharge. -
370.7 420.7 mm -
373.6 423.6 rnm
model -
(14.59 16.56 in) -
114.71 16.68 in1
Non-turboehargsr -
369.3 419.3'rnm -
372.7 422.7 mm
model -
(14.54 16.51 in) 114.67. 16.64 in1

6 mm 10.24 in)

1 Condition:
A t vehicle center
normal tire pressure
on level ground

BF-8
BODY END AND DOOR
Front End (Cont'd)

Side member -
'Hood stay
When removinglinrtalling hood stay lower mounting
(at rtay-body portion). be careful not to drop colier.

Frontbumpar reinforcement

: Greare-up w i n t
PJ) : N m (kgm. ft-lbl
: Bumper assembly
mounting bolts

BF-9
BODY END AND DOOR

Back door adjustment: Adjust a t hinge for proper back door fit.
Lock: Adjust lock so that it is in the center of the striker. After adjusting, check back door lock opera-
tion.
Bumper fascia: It is made of plastic, so do not use excessive force and take care to keep oil away from it.
When adjusting or removing/installing back door or removing/installing back door lock system, check
theft warning system operation.
Bumper shock absorber inspection: It's the same as front bumper. Refer to "Front End".

WARNING:
a. Be careful not to scratch back door stay when installing back door. A scratched stay may cause gas
leakage.
b. The contents of the back door stay and bumper shock absorber are under pressure. Do not take apart,
puncture, apply heat or allow fire near it.

PJ) 21-26
PJ) 5.1 .6.5 10.52.0.88.3.8
12.1 .2.7,
Pay attention to installing direction.
15.201

Westherstrip installation
Align white marking wit
center hinge.
Bumper rubber -
,[ 1
-9 13.16
-
11.3 1.6,9. 12)

: Doublefaced adhesive tape

BF-10
BODY END AND DOOR
Rear End (Cont'd)

Back door lock adjustment ' Shock
-absorber

(0113-
11.3

.
Shoslc absorber impation:
3.8.4.8)
I R.fw to fmnt b u m p r shock absorber
(BODY FRONT END)

2 se.mr 2+2 I.8tnr

Turbochargar 631.9-681.9mm 628.0-578.0 mm
model 120.94.22.91 id 120.79 .22.76 in)
Non-turbochamer- I -
539.7 689.7 mm I -
634.6 684.6 mm
mods1 I -
121.26 23.22 in1 I -
121.06 23.02 in)

Condition:
Y At vehicle center

Curb weight & normal
tire pressure on
level ground

[91 : N m (kg-m, ft-lb)
: Grease-up points
: Bumper assembly
mounting boltsand nuts
SBF472D

BF-11
BODY END AND DOOR
Back Door and Fuel Filler Lid Opener

Opener cable: Do not attempt to bend cable using excessive force.
0 After installation, make sure that back door and fuel filler lid open smoothly.

Fuel filler lid opener

Back door lock H

Back door lock

Approx.

SBF699D

BF-12
BODYENDANDDOOR
Front Door

0 After adjusting door or door lock, check door lock operation.
When adjusting or removing/installing door or removinglinstalling door lock system or door switch,
check theft warning system operation.

b l l crank adjustment

Window stoppr diu*ment @
, Inside handle installetion

ow stopper adjustment @

Stopper lglass side1
Window guid. nil adjustment @
Window wide rail

( . .3.8,22 - 271
30

-
0.5 1.5 bm
10.020~0.059in1

lm
I
Striker adjustment

: Grease-up paints
: N m Ikg-m.ft-ibl

SBF834D
BODY END AND DOOR
Front Door (Cont'd)

POWER WlNDOW/WlRlNG DIAGRAM
BODY END AND DOOR
Front Door (Cont'd)

POWER DOOR LOCKMllRlNG DIAGRAM

f
1_

Y %
88
3 P

BF-15
INSTRUMENT

These parts are made of plastic, so do not use excessive force and be careful not to damage them.
When you remove instrument assembly, you should remove radio, meter and defroster grille.

Remove griller by raising Remove griller by raising
pawls using flatbladed pawls using flatbladed
screwdriver. screwdriver.

I I
Removal: Instrument combinstion w i t c h Instrument combination
(When removing combination mmer
first mmwe comb

: Instrument assembly
Instrument combination
mounting screw
w i t c h basement
F i r s remove nut securing instrument combination witch basement. then remove instrument
combination witch. (Instrument combination witches are secured at hooks and basements.)
SBF478D

BF-I 6
SEAT
When removing or installing the seat trim, carefully handle it to keep dirt out and avoid damage.

Front Manual Driver Seat

Remow after mtback trim is
rolled back.

(91 1 3 - 1 6
(1.3 .1.6,9 - 12)

(4.4.5.6,32.41)
(91 2 1 . 2 6
(2.1 .2.7,

(4.4.5.6,32.411

(91 43 . 5 5 (4.4.5.6.32 - 41)

(91 N.m (kgm.ft-lb)
a:
Greareup points
(Do not apply too much grease as
it will drip.)

(91 43 - 5514.4 - 6.6.32 - 41
-
(2.1 2.7, 15 - 20) SBF527C

BF-17
SEAT
Front Semi Power Driver Seat

(4.4-5.8.32-41)

14.4-5.6.32-41)

\LD 21 - 2 6
(2.1 .2.7, 15.201

BF-18
SEAT
Front Semi Power Driver Seat (Cont'd)

Remove aftw seat back trim
is rolled back
0

11.3 .1.6.9 - 121
Lumbar support switch

14.4.5.8,
32-41)

I
(91 : N.m Ikgm. ft-lbl
: Grearevp points
(Donot apply too much grease as it will drip.)
@ : Sealant points SBF706D

BF-19
SEAT
Front Semi Power Driver Seat (Cont'd)
AIR DIAGRAM

.. ....

BF-20
SEAT
Front Semi Power Driver Seat (Cont'd)

WIRING DIAGRAM

SBF537D

BF-21
SEAT
Front Full Power Driver Seat

. ..

BF-22
SEAT
Front Full Power Driver Seat (Cont'd)

SBF835D

BF-23
SEAT
Front Full Power Driver Seat (Cont'd)

AIR DIAGRAM

. B wre air hoses are not crushd.
.
If how connection ia dirconnoctd. apply Iulant t o
how mnnection t o prevent air l u b e .(0 portion only)
0 Be w n air pump b free from dust, foreign ruktanm, ate.
lnmll ptny v d n in i t s p ~ o p dirmction.
r
Air pump op.r.ta only w h m each w i t c h is turned ON.
e M.la-fHnala typ COnwMrs h O-rings.
n
B. extremely careful that O-rings S not droppad, damaged
.
I
or roiled.

Hose connection

: Hose connection
[Male-Female connector type)

@ . Sealant portion

[Seatback ridel

Lumbar support w i t c h

Thigh support w i t c h Thigh

ridel

SBF53lC

BF-24
SEAT
Front Full Power Driver Seat (Cont'd)

WIRING DIAGRAM

BF-25
Front Passenger Seat

0 Basically, this seat is the same as manual type front driver seat. 2 + 2 seater model differs from manual
type front seat in the walk-in mechanism has been added to it. Refer to the description on manual type
driver seat except for walk-in mechanism.

WALK-IN MECHANISM

Release lever
7
Seatback frame

l Release wire assembly

Release wire assembly

WaIk.in wira .d]u$tmMt
When auembling, make sum
them is no play left. SBF528C

BF-26
SEAT
Rear Seat

: N m (kgm,ft-lbl

I Mom striker all theway UP and tighten. I

SBF836D

BF-27
SEAT BELT

Refer to MA section for installation of seat belts.
GLL model has been equipped with seat belts with tension reducer. This unit reduces the force required
to pull out seat belt while in use, and lessens pressure on the shoulder and hips for greater comfort,

TENSION REDUCER WIRING DIAGRAM
r 7

urmnml
III I I I IA1I
z u FUSE BLOCK
@

I SEAT BELT SWITCH
TENSION REDUCER IParsengerl (Main (Pauengsrl
l l n l a e retractor) harness)

TENSION REDUCER (Driver)
( I n t a e retractor1
(Power
SEAT BELT
harness) erl

To time control unit
(Seat belt warning I m p 1

BODY
GROUND
1R.H. side1

BODYGROUNO
1L.H. side1 (Rear panel1
SBF791D

TENSION REDUCE OPERATION

Fully Seat belt stroke Fully
retracted pulled out
SEW406

BF-28
INTERIOR AND EXTERIOR
When removing clip or fastener, refer t o CLIP & FASTENER.
When handling trim or molding, do not use excessive force and take care not to damage them.

Inside Trim

SIDE, LUGGAGE AND FLOOR TRIM

12 seater model

loor mat

I Luggage

BF-29
INTERIOR AND EXTERIOR
Inside Trim (Cont'd)

ROOF TRIM
Front portion Rear portion

Roof trim

-Welt 1

S8F591C

BF-30
INTERIOR AND EXTERIOR
Exterior

0 Apply sealing compound where necessary while installing parts.
0 When applying sealing compound, be careful that the sealing compound does not protrude from parts.

SBF482D

@ Front side spoiler
0 Front side spoiler is affixed to body panel with
double-faced adhesive tape, clip and fastener.
Remove it only if it is necessary to do so.
Removal:
1. Heat molding portion to 25 to 35

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo