Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Murano 2003-2007.2009 Approved Nissan Murano 2006 ma

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download ma documenatation <<

Text preview - extract from the document

MAINTENANCE

L MAINTENANCE

SECTION
MAINTENANCE
MA B

E
CONTENTS
PREPARATION .......................................................... 3
. INSTALLATION .................................................. 19 . F
Special Service Tools .............................................. 3
. Checking EVAP Vapor Lines ................................. 19 .
Commercial Service Tools ....................................... 3 . CHASSIS AND BODY MAINTENANCE .................. 20 .
GENERAL MAINTENANCE ...................................... 4 . Checking Exhaust System ..................................... 20 . G
Explanation of General Maintenance ...................... 4 . Checking CVT Fluid ............................................... 20 .
PERIODIC MAINTENANCE ...................................... 6 . FLUID LEVEL CHECK ....................................... 20 .
Introduction of Periodic Maintenance ...................... 6 . FLUID CONDITION CHECK .............................. 21 .
H
Schedule 1 .............................................................. 7
. Changing CVT Fluid .............................................. 21 .
EMISSION CONTROL SYSTEM MAINTE- Checking Transfer Oil ............................................ 21 .
NANCE ................................................................. 7
. Changing Transfer Oil ........................................... 22 .
CHASSIS AND BODY MAINTENANCE .............. 8 . Checking Propeller Shaft ....................................... 22 . I
Schedule 2 .............................................................. 8
. Checking Differential Gear Oil ............................... 22 .
EMISSION CONTROL SYSTEM MAINTE- Changing Differential Gear Oil ............................... 23 .
NANCE ................................................................. 8
. Balancing Wheels (Bonding Weight Type) ............ 23 . J
CHASSIS AND BODY MAINTENANCE .............. 9 . REMOVAL .......................................................... 23.
RECOMMENDED FLUIDS AND LUBRICANTS ..... 10 . WHEEL BALANCE ADJUSTMENT .................... 23 .
Fluids and Lubricants ............................................ 10
. Tire Rotation .......................................................... 24
.
K
SAE Viscosity Number ...........................................11 . Checking Brake Fluid Level and Leaks ................. 25 .
GASOLINE ENGINE OIL ....................................11 . Checking Brake Lines and Cables ........................ 25 .
Anti-Freeze Coolant Mixture Ratio .........................11 . Changing Brake Fluid ............................................ 25 .
ENGINE MAINTENANCE ........................................ 12 . Checking Disc Brake ............................................. 25 . MA
Checking Drive Belts ............................................. 12
. ROTOR ............................................................... 25
.
Tension Adjustment ............................................... 12
. CALIPER ............................................................ 26
.
ALTERNATOR AND A/C COMPRESSOR BELT 13 ... PAD .................................................................... 26
. M
POWER STEERING OIL PUMP BELT .............. 13 . Checking Steering Gear and Linkage .................... 26 .
Changing Engine Coolant ..................................... 13 . STEERING GEAR .............................................. 26 .
DRAINING ENGINE COOLANT ........................ 14 . STEERING LINKAGE ........................................ 26 .
REFILLING ENGINE COOLANT ....................... 14 . Checking Power Steering Fluid and Lines ............. 26 .
FLUSHING COOLING SYSTEM ........................ 15 . Axle and Suspension Parts ................................... 27 .
Checking Fuel Lines .............................................. 16
. Drive Shaft ............................................................. 27
.
Changing Air Cleaner Filter ................................... 16 . Lubricating Locks, Hinges and Hood Latch ........... 28 .
VISCOUS PAPER TYPE .................................... 16 . Checking Seat Belt, Buckles, Retractors, Anchors
Changing Engine Oil ............................................. 17. and Adjusters ......................................................... 28
.
Changing Oil Filter ................................................ 17
. SERVICE DATA AND SPECIFICATIONS (SDS) ..... 30 .
REMOVAL .......................................................... 17
. Standard and Limit ................................................. 30.
INSTALLATION .................................................. 18. BELT DEFLECTION AND TENSION ................. 30 .
INSPECTION AFTER INSTALLATION .............. 18 . ENGINE COOLANT CAPACITY (APPROXI-
Changing Spark Plugs (Platinum-Tipped Type) .... 18 . MATE) ................................................................. 30
.
REMOVAL .......................................................... 18
. RADIATOR ......................................................... 30.
INSPECTION AFTER REMOVAL ...................... 19 . ENGINE OIL CAPACITY (APPROXIMATE) ....... 30 .

Revision: 2005 September MA-1 2006 Murano
SPARK PLUG (PLATINUM-TIPPED TYPE) ....... 30
. WHEEL BALANCE .............................................31 .
Tightening Torque ..................................................31
.

Revision: 2005 September MA-2 2006 Murano
PREPARATION

PREPARATION PFP:00002
A
Special Service Tools NLS0004G

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number B
(Kent-Moore No.) Description
Tool name

KV10115801 Removing and installing oil filter
C
(J38956) a: 64.3 mm (2.531 in)
Oil filter wrench

S-NT375

E
Commercial Service Tools NLS0004H

(Kent-Moore No.)
Description
Tool name F
( -- ) Loosening nuts and bolts
Power tool
G

H
PBIC0190E

( -- ) Removing and installing spark plug
Spark plug wrench I

S-NT047

(BT3373-F) Checking drive belt tension K
Belt tension gauge

AMA126
M

Revision: 2005 September MA-3 2006 Murano
GENERAL MAINTENANCE

GENERAL MAINTENANCE PFP:00000

Explanation of General Maintenance NLS0004I

General maintenance includes those items which should be checked during the normal day-to-day operation
of the vehicle. They are essential if the vehicle is to continue operating properly. The owners can perform
checks and inspections themselves or have their NISSAN dealers do them.
OUTSIDE THE VEHICLE
The maintenance items listed here should be performed from time to time, unless otherwise specified.
Item Reference page
Tires Check the pressure with a gauge, including the spare, at least once a month
and always prior to a long distance trips. Adjust to the specified pressure if nec- --
essary. Check carefully for damage, cuts or excessive wear.
Wheel nuts When checking the tires, make sure no nuts are missing, and check for any
--
loose nuts. Tighten if necessary.
Clean the windshield on a regular basis. Check the windshield at least every six
Windshield --
months for cracks or other damage. Repair as necessary.
Tire rotation Tires should be rotated every 12,000 km (7,500 miles). MA-24
Wheel alignment and If the vehicle pulls to either side while driving on a straight and level road, or if
balance you detect uneven or abnormal tire wear, there may be a need for wheel align-
MA-23, FSU-5
ment. If the steering wheel or seat vibrates at normal highway speeds, wheel
balancing may be needed.
Windshield wiper
Check for cracks or wear if they do not wipe properly. --
blades
Doors and engine Check that all doors and the engine hood operate smoothly as well as the trunk
hood lid and back hatch. Also make sure that all latches lock securely. Lubricate if
necessary. Make sure that the secondary latch keeps the hood from opening
MA-28
when the primary latch is released.
When driving in areas using road salt or other corrosive materials, check lubri-
cation frequently.
Lamps Make sure that the headlamps, stop lamps, tail lamps, turn signal lamps, and
other lamps are all operating properly and installed securely. Also check head- --
lamp aim. Clean the headlamps on a regular basis.

INSIDE THE VEHICLE
The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the
vehicle, etc.
Item Reference page
Warning lamps and
Make sure that all warning lamps and chimes are operating properly. --
chimes
Windshield wiper and Check that the wipers and washer operate properly and that the wipers do not
--
washer streak.
Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient
--
quantity when operating the heater or air conditioner.
Steering wheel Check that it has the specified play. Be sure to check for changes in the steering
condition, such as excessive play, hard steering or strange noises. --
Free play: Less than 35 mm (1.37 in)
Seats Check seat position controls such as seat adjusters, seatback recliner, etc. to
make sure they operate smoothly and that all latches lock securely in every
position. Check that the head restrains move up and down smoothly and that --
the locks (if equipped) hold securely in all latched positions. Check that the
latches lock securely for folding-down rear seatbacks.
Seat belts Check that all parts of the seat belt system (e.g. buckles, anchors, adjusters and
retractors) operate properly and smoothly, and are installed securely. Check the MA-28
belt webbing for cuts, fraying, wear or damage.
Accelerator pedal Check the pedal for smooth operation and make sure the pedal does not catch
--
or require uneven effort. Keep the floor mats away from the pedal.
Brakes Check that the brake does not pull the vehicle to one side when applied. --

Revision: 2005 September MA-4 2006 Murano
GENERAL MAINTENANCE

Item Reference page
A
Brake pedal and Check the pedal for smooth operation and make sure it has the proper distance
booster under it when depressed fully. Check the brake booster function. Be sure to BR-6, BR-20
keep the floor mats away from the pedal.
Parking brake Check that the pedal has the proper travel and make sure that the vehicle is B
PB-2
held securely on a fairly steep hill when only the parking brake is applied.
CVT P (Park) position On a fairly steep hill check that the vehicle is held securely with the selector
--
mechanism lever in the P (Park) position without applying any brakes. C
UNDER THE HOOD AND VEHICLE
The maintenance items listed here should be checked periodically (e.g. each time you check the engine oil or refuel).
Item Reference page D
Windshield washer
Check that there is adequate fluid in the tank. --
fluid
E
Engine coolant level Check the coolant level when the engine is cold. MA-13
Radiator and hoses Check the front of the radiator and clean off any dirt, insects, leaves, etc., that
may have accumulated. Make sure the hoses have no cracks, deformation, --
deterioration or loose connections. F
Brake fluid level Make sure that the brake fluid level is between the "MAX" and "MIN" lines on the
MA-25
reservoir.
Battery Check the fluid level in each cell. It should be between the "MAX" and "MIN" G
lines. Vehicles operated in high temperatures or under severe conditions require --
frequent checks of the battery fluid level.
Engine drive belts Make sure that no belt is frayed, worn, cracked or oily. MA-12 H
Engine oil level Check the level on the oil level gauge after parking the vehicle on a level spot
MA-17
and turning off the engine.
Power steering fluid Check the level on the dipstick with the engine off. Check the lines for improper I
MA-26
level and lines attachment, leaks, cracks, etc.
Exhaust system Make sure there are no loose supports, cracks or holes. If the sound of the
exhaust seems unusual or there is a smell of exhaust fumes, immediately locate MA-20 J
the trouble and correct it.
Underbody The underbody is frequently exposed to corrosive substances such as those
used on icy roads or to control dust. It is very important to remove these sub-
K
stances, otherwise rust will form on the floor pan, frame, fuel lines and around
--
the exhaust system. At the end of winter, the underbody should be thoroughly
flushed with plain water, being careful to clean those areas where mud and dirt
can easily accumulate. MA
Fluid leaks Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle
has been parked for a while. Water dripping from the air conditioner after use is
--
normal. If you should notice any leaks or gasoline fumes are evident, check for
M
the cause and correct it immediately.

Revision: 2005 September MA-5 2006 Murano
PERIODIC MAINTENANCE

PERIODIC MAINTENANCE PFP:00026

Introduction of Periodic Maintenance NLS0004J

Two different maintenance schedules are provided, and should be used, depending upon the conditions in
which the vehicle is mainly operated. After 60,000 miles (96,000 km) or 48 months, continue the periodic
maintenance at the same mileage/time intervals.
Follow Periodic Maintenance Schedule 1 if the driving habits frequently include Emission Control Sys-
one or more of the following driving conditions: tem Maintenance
q Repeated short trips of less than 5 miles (8 km).
MA-7
q Repeated short trips of less than 10 miles (16 km) with outside temperatures
remaining below freezing.
Schedule 1 q Operating in hot weather in stop-and-go "rush hour" traffic.
q Extensive idling and/or low speed driving for long distances, such as police, Chassis and Body
taxi or door-to-door delivery use. Maintenance
q Driving in dusty conditions. MA-8
q Driving on rough, muddy, or salt spread roads.
q Towing a trailer, using a camper or a car-top carrier.
Follow Periodic Maintenance Schedule 2 if none of driving conditions shown in Emission Control Sys-
MA-8
Schedule 1 apply to the driving habits. tem Maintenance
Schedule 2
Chassis and Body
MA-9
Maintenance

Revision: 2005 September MA-6 2006 Murano
PERIODIC MAINTENANCE

Schedule 1 NLS0004K

EMISSION CONTROL SYSTEM MAINTENANCE A
Abbreviations: R = Replace. I = Inspect. Correct or replace if necessary. [ ]: At the mileage intervals only
MAINTENANCE OPERATION MAINTENANCE INTERVAL Reference
Perform at number of miles, Miles x 1,000 3.75 7.50 11.25 15 18.75 22.5 26.25 30 Section - B
kilometers or months, which- (km x 1,000) (6) (12) (18) (24) (30) (36) (42) (48) Page or -
ever comes first. Months 3 6 9 12 15 18 21 24 Content Title

Drive belts NOTE (1) MA-12 C
Air cleaner filter NOTE (2) [R] MA-16
EVAP vapor lines I* MA-19
D
Fuel lines I* MA-16
Fuel filter NOTE (3) -
Engine coolant NOTE (4) MA-13 E
Engine oil R R R R R R R R MA-17
Engine oil filter (Use part No.
15208 31U00 or 15208 R R R R R R R R MA-17 F
65F00 or equivalent.)
Spark plugs (PLATINUM-
Replace every 105,000 miles (169,000 km). MA-18
TIPPED type) G
EM-88,
Intake & exhaust valve clear-
NOTE (5) "Valve Clear-
ance*
ance"
H
MAINTENANCE OPERATION MAINTENANCE INTERVAL Reference
Perform at number of miles, Miles x 1,000 33.75 37.5 41.25 45 48.75 52.5 56.25 60 Section -
kilometers or months, which- (km x 1,000) (54) (60) (66) (72) (78) (84) (90) (96) Page or - I
ever comes first. Months 27 30 33 36 39 42 45 48 Content Title

Drive belts NOTE (1) I* MA-12
J
Air cleaner filter NOTE (2) [R] MA-16
EVAP vapor lines I* MA-19
Fuel lines I* MA-16 K
Fuel filter NOTE (3) -
Engine coolant NOTE (4) R* MA-13
Engine oil R R R R R R R R MA-17 MA
Engine oil filter (Use part No.
15208 31U00 or 15208 65F00 R R R R R R R R MA-17
or equivalent.) M
Spark plugs (PLATINUM-
Replace every 105,000 miles (169,000 km). MA-18
TIPPED type)
EM-88,
Intake & exhaust valve clear-
NOTE (5) "Valve Clear-
ance*
ance"
NOTE:
(1) After 60,000 miles (96,000 km) or 48 months, inspect every 15,000 miles (24,000 km) or 12 months. Replace the drive belts if found
damaged.
(2) If operating mainly in dusty conditions, more frequent maintenance may be required.
(3) Maintenance-free item. For service procedures, refer to FL section.
(4) After 60,000 miles (96,000 km) or 48 months, replace every 30,000 miles (48,000 km) or 24 months.
(5) If valve noise increases, inspect valve clearance.
* Maintenance items and intervals with "*" are recommended by NISSAN for reliable vehicle operation. The owner need not perform
such maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are
required.

Revision: 2005 September MA-7 2006 Murano
PERIODIC MAINTENANCE

CHASSIS AND BODY MAINTENANCE
Abbreviations: R = Replace. I = Inspect. Correct or replace if necessary.
MAINTENANCE OPERATION MAINTENANCE INTERVAL Reference
Perform at number of miles, Miles x 1,000 3.75 7.50 11.25 15 18.75 22.5 26.25 30 Section - Page
kilometers or months, (km x 1,000) (6) (12) (18) (24) (30) (36) (42) (48) or - Content
whichever comes first. Months 3 6 9 12 15 18 21 24 Title

MAINTENANCE OPERATION MAINTENANCE INTERVAL Reference
Perform at number of miles, Miles x 1,000 33.75 37.5 41.25 45 48.75 52.5 56.25 60 Section - Page
kilometers or months, (km x 1,000) (54) (60) (66) (72) (78) (84) (90) (96) or - Content
whichever comes first. Months 27 30 33 36 39 42 45 48 Title

Brake lines & cables I I MA-25
Brake pads & rotors I I I I MA-25
CVT fluid NOTE (1) I I MA-20, MA-21
Transfer oil & differential
NOTE (2) I I MA-21, MA-22
gear oil
Steering gear & linkage,
I I I I MA-26, MA-27
axle & suspension parts
Tire rotation NOTE (3) MA-4, MA-24
Drive shaft boots and pro-
I I I I MA-27, MA-22
peller shaft (AWD models)
Exhaust system I I I I MA-20
In-cabin microfilter R R ATC-118
NOTE:
(1) If towing a trailer, using a camper or a car-top carrier, or driving on rough or muddy roads, inspect CVT fluid deterioration with CON-
SULT-II every 60,000 miles (96,000 km), then change CVT fluid NS-2 if necessary. (Refer to CVT-66, "Check CVT Fluid Deterioration
Date" .) And if CONSULT-II is not available, change (not just inspect) CVT fluid NS-2 every 60,000 miles (96,000 km). Using transmis-
sion fluid other than Genuine Nissan CVT Fluid NS-2 will damage the CVT, which is not covered by the NISSAN new vehicle
limited warranty.
(2) If towing a trailer, using a camper or a car-top carrier, or driving on rough or muddy roads, change (not just inspect) oil at every
30,000 miles (48,000) or 24 months.
(3) Refer to "Tire rotation" under the "GENERAL MAINTENANCE" heading earlier in this section.

Schedule 2 NLS0004L

EMISSION CONTROL SYSTEM MAINTENANCE
Abbreviations: R = Replace. I = Inspect. Correct or replace if necessary. [ ]: At the mileage intervals only
MAINTENANCE OPERATION MAINTENANCE INTERVAL
Reference Sec-
Perform at number of miles, Miles x 1,000 7.5 15 22.5 30 37.5 45 52.5 60 tion - Page or -
kilometers or months, whichever (km x 1,000) (12) (24) (36) (48) (60) (72) (84) (96) Content Title
comes first. Months 6 12 18 24 30 36 42 48
Drive belts NOTE (1) I* MA-12
Air cleaner filter [R] [R] MA-16

Revision: 2005 September MA-8 2006 Murano
PERIODIC MAINTENANCE

MAINTENANCE OPERATION MAINTENANCE INTERVAL
Reference Sec- A
Perform at number of miles, Miles x 1,000 7.5 15 22.5 30 37.5 45 52.5 60 tion - Page or -
kilometers or months, whichever (km x 1,000) (12) (24) (36) (48) (60) (72) (84) (96) Content Title
comes first. Months 6 12 18 24 30 36 42 48
EVAP vapor lines I* I* MA-19 B
Fuel lines I* I* MA-16
Fuel filter NOTE (2) -
C
Engine coolant NOTE (3) R* MA-13
Engine oil R R R R R R R R MA-17
Engine oil filter (Use part No. D
15208 31U00 or 15208 65F00 R R R R R R R R MA-17
or equivalent.)
Spark plugs (PLATINUM- E
Replace every 105,000 miles (169,000 km). MA-18
TIPPED type)
Intake & exhaust valve clear- EM-88, "Valve
NOTE (4)
ance* Clearance"
F
NOTE:
(1) After 60,000 miles (96,000 km) or 48 months, inspect every 15,000 miles (24,000 km) or 12 months. Replace the drive belts if found
damaged.
(2) Maintenance-free item. For service procedures, refer to FL section. G
(3) After 60,000 miles (96,000 km) or 48 months, replace every 30,000 miles (48,000 km) or 24 months.
(4) If valve noise increases, inspect valve clearance.
* Maintenance items and intervals with "*" are recommended by NISSAN for reliable vehicle operation. The owner need not perform H
such maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are
required

CHASSIS AND BODY MAINTENANCE I
Abbreviations: R = Replace. I = Inspect. Correct or replace if necessary.
MAINTENANCE OPERATION MAINTENANCE INTERVAL
Reference Sec-
Perform at number of miles, kilo- Miles x 1,000 7.5 15 22.5 30 37.5 45 52.5 60 tion - Page or - J
meters or months, whichever (km x 1,000) (12) (24) (36) (48) (60) (72) (84) (96) Content Title
comes first. Months 6 12 18 24 30 36 42 48
Brake lines & cables I I I I MA-25 K
Brake pads & rotors I I I I MA-25
CVT fluid NOTE (1) I I I I MA-20
Transfer oil & differential gear oil I I I I MA-21, MA-22 MA
Steering gear & linkage, axle &
I I MA-26, MA-27
suspension parts
Tire rotation NOTE (2) MA-4, MA-24
M

Drive shaft boots and propeller
I I I I MA-27, MA-22
shaft (AWD models)
Exhaust system I I MA-20
In-cabin microfilter R R R R ATC-118
NOTE:
(1) Using transmission fluid other than Genuine Nissan CVT Fluid NS-2 will damage the CVT, which is not covered by the NIS-
SAN new vehicle limited warranty.
(2) Refer to "Tire rotation" under the "GENERAL MAINTENANCE" heading earlier in this section.

Revision: 2005 September MA-9 2006 Murano
RECOMMENDED FLUIDS AND LUBRICANTS

RECOMMENDED FLUIDS AND LUBRICANTS PFP:00000

Fluids and Lubricants NLS0004M

Capacity (Approximate)
Recommended Fluids/Lubricants
US measure Imp measure Liter
With oil filter
4-1/4 qt 3-1/2 qt 4.0 q API Certification Mark*1
Engine oil change
Drain and refill q API grade SG/SH, Energy Conserving I & II or
Without oil fil-
3-7/8 qt 3-1/4 qt 3.7 API grade SJ or SL, Energy Conserving*1
ter change
q ILSAC grade GF-I, GF-II & GF-III *1
Dry engine (Overhaul) 5-1/4 qt 4-3/8 qt 5.0
With reservoir
Cooling sys- 10-1/8 qt 8-1/2 qt 9.6 Genuine NISSAN Long Life Antifreeze/Coolant
tank
tem or equivalent
Reservoir tank 7/8 qt 3/4 qt 0.8
CVT fluid 10-6/8 qt 9 qt 10.2 Genuine NISSAN CVT Fluid NS-2 *2
Differential gear oil 1-1/8 pt 1 pt 0.55 API GL-5, Viscosity SAE 80 W-90 *3
Transfer oil 5/8 pt 1/2 pt 0.31 API GL-5, Viscosity SAE 80 W-90
Power steering fluid (PSF) 1-1/8 qt 7/8 qt 1.0 Genuine NISSAN PSF or equivalent*4
Genuine NISSAN Super Heavy Duty Brake
Brake fluid -- -- -- Fluid*5 or equivalent
DOT 3 (US FMVSS No. 116)
Multi-purpose grease -- -- -- NLGI No. 2 (Lithium soap base)
Genuine NISSAN Windshield Washer Concen-
Windshield washer fluid -- -- --
trate Cleaner & Antifreeze or equivalent
Refer toGI-6, "Precautions for Fuel (Unleaded
Fuel recommendation -- -- --
Premium Gasoline Recommended)"
*1: For further details, see "SAE Viscosity Number".
*2: Using transmission fluid other than Genuine NISSAN CVT Fluid NS-2 will damage the CVT, which is not covered by the NIS-
SAN new vehicle limited warranty.
*3: For hot climates, viscosity SAE 90 is suitable for ambient temperatures above 0

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo