Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Micra 2003-2006 Approved 05k12e EI
<< Back |
HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download
Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing.
If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download EI documenatation <<Text preview - extract from the documentEXTERIOR & INTERIOR
I BODY
A
EXTERIOR & INTERIOR
SECTION EI B
C
D
E
CONTENTS
PRECAUTIONS ......................................................... 3
. REMOVAL .......................................................... 18
. F
Precautions for Supplemental Restraint System INSTALLATION .................................................. 18
.
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Removal and Installation (C+C) ............................. 19 .
SIONER" ................................................................. 3
. REMOVAL .......................................................... 19
. G
PrecautionsforProcedureswithoutCowlTopCover 3 ..... INSTALLATION .................................................. 19
.
Precautions ............................................................. 3
. DOOR FINISHER ..................................................... 20
.
CLIP AND FASTENER .............................................. 4 . Removal and Installation ....................................... 20.
H
Clip and Fastener .................................................... 4
. REMOVAL .......................................................... 20
.
FRONT BUMPER ...................................................... 5. INSTALLATION .................................................. 21
.
Removal and Installation ......................................... 5. BACK DOOR TRIM .................................................. 22.
REMOVAL ............................................................ 7
. Removal and Installation ....................................... 22. EI
INSTALLATION .................................................... 7
. REMOVAL .......................................................... 22
.
REAR BUMPER ........................................................ 8
. INSTALLATION .................................................. 22
.
Removal and Installation ......................................... 8. TRUNK LID TRIM .................................................... 23
. J
REMOVAL ............................................................ 9
. Removal and Installation ....................................... 23.
INSTALLATION .................................................. 10. REMOVAL .......................................................... 23
.
FRONT GRILLE ........................................................11
. INSTALLATION .................................................. 23
.
K
Removal and Installation ........................................11 . TRUNK LID FINISHER ............................................ 24 .
REMOVAL ...........................................................11
. Removal and Installation ....................................... 24.
INSTALLATION ...................................................11. REMOVAL .......................................................... 24
.
FRONT DEFLECTOR .............................................. 12 . INSTALLATION .................................................. 24
. L
Removal and Installation ....................................... 12 . BODY SIDE TRIM .................................................... 25
.
REMOVAL .......................................................... 12
. Removal and Installation (5-Door) ......................... 25 .
INSTALLATION .................................................. 12. REMOVAL .......................................................... 25
. M
COWL TOP .............................................................. 13
. INSTALLATION .................................................. 26
.
Removal and Installation ....................................... 13 . Removal and Installation (3-Door) ......................... 26 .
REMOVAL .......................................................... 13
. REMOVAL .......................................................... 26
.
INSTALLATION .................................................. 13. INSTALLATION .................................................. 27
.
FENDER PROTECTOR ........................................... 14 . Removal and Installation (C+C) ............................. 28 .
Removal and Installation ....................................... 14 . REMOVAL .......................................................... 28
.
ROOF SIDE MOLDING ........................................... 15 . INSTALLATION .................................................. 29
.
Removal and Installation ....................................... 15 . FLOOR TRIM ........................................................... 30
.
REMOVAL .......................................................... 15
. Removal and Installation ....................................... 30.
INSTALLATION .................................................. 15. REMOVAL .......................................................... 31
.
WINDSHIELD MOLDING ........................................ 16 . INSTALLATION .................................................. 32
.
Removal and Installation ....................................... 16 . HEADLINER ............................................................. 33
.
REMOVAL .......................................................... 16
. Removal and Installation ....................................... 33.
INSTALLATION .................................................. 17. REMOVAL .......................................................... 33
.
DOOR OUTSIDE MOLDING ................................... 18 . INSTALLATION .................................................. 34
.
Removal and Installation (3 Door and 5 Door) ...... 18 .
EI-1
WINDSHIELD FINISHER ......................................... 36 . BACK SIDE TRIM ....................................................39
.
Removal and Installation ....................................... 36
. Removal and Installation ...................................... ..39
.
REMOVAL .......................................................... 36
. REMOVAL ...........................................................39
.
INSTALLATION ................................................... 36
. INSTALLATION ...................................................39
.
ROOF FINISHER ...................................................... 37
. LUGGAGE FLOOR TRIM ........................................40 .
Removal and Installation ....................................... 37
. Removal and Installation ...................................... ..40
.
REMOVAL .......................................................... 37
. REMOVAL ...........................................................40
.
INSTALLATION ................................................... 37
. INSTALLATION ...................................................41
.
REAR PARCEL SHELF ........................................... 38 . TRUNK ROOM TRIM ...............................................42 .
Removal and Installation ....................................... 38
. Removal and Installation ...................................... ..42
.
REMOVAL .......................................................... 38
. REMOVAL ...........................................................42
.
INSTALLATION ................................................... 38
. INSTALLATION ...................................................42
.
EI-2
PRECAUTIONS
PRECAUTIONS PFP:00001
A
Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EIS004PB
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along B
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual. C
WARNING:
q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer. D
q Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section. E
q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors. F
Precautions for Procedures without Cowl Top Cover EIS00DXT
When performing the procedure after removing cowl top cover, cover G
the lower end of windshield with urethane, etc.
H
EI
PIIB3706J J
Precautions EIS004PC
q When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which K
may get in the way with cloth.
q When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.
q Keep removed parts protected with cloth. L
q If a clip is deformed or damaged, replace it.
q If an unreusable part is removed, replace it with a new one.
q Tighten bolts and nuts firmly to the specified torque. M
q After re-assembly has been completed, make sure each part functions correctly.
q Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
q Do not use any organic solvent, such as thinner or benzine.
EI-3
CLIP AND FASTENER
CLIP AND FASTENER PFP:76906
Clip and Fastener EIS004PD
SIIA0315E
EI-4
FRONT BUMPER
FRONT BUMPER PFP:F2022
A
Removal and Installation EIS004NZ
q Bumper fascia is made of plastic. Do not use excessive force and be sure to protect it from exposure to
oil. B
C
D
E
F
G
H
EI
J
K
L
M
EI-5
FRONT BUMPER
MIIB9228E
1. Bumper fascia 2. Bumper reinforcement 3. Bumper side bracket (upper)
4. Bumper side bracket (lower) 5. Bumper stay 6. Bumper energy absorber
EI-6
FRONT BUMPER
REMOVAL
1. Remove front grille. Refer to EI-11, "FRONT GRILLE" . A
2. Remove bumper fascia installation clip.
3. Remove fender protector lower fixing bolts. Remove fender protectors (right, left). Refer to EI-14,
"FENDER PROTECTOR" . B
4. Remove the bolts holding bumper fascia to front fender.
5. Disconnect front fog lamp harness connector (if equipped). Disconnect headlamp washer tube (if
equipped). C
6. Pull the bumper fascia horizontal from front fender mounting surface, disengage the clip, and remove.
7. Remove front bumper energy absorber. Remove front bumper protector.
D
8. Remove the bumper side brackets (upper and lower) from the bumper fascia.
9. Remove bolts and nuts and then remove bumper reinforcement.
10. Remove bolts and bumper stay. E
INSTALLATION
Install in the reverse order of removal.
F
G
H
EI
J
K
L
M
EI-7
REAR BUMPER
REAR BUMPER PFP:H5022
Removal and Installation EIS004O0
Bumper fascia is made of plastic. Do not use excessive force and be sure to protect it from exposure to oil.
MIIB9229E
1. Bumper side bracket 2. Bumper energy shock absorber 3. Rear panel (lower)
4. Bumper fascia 5. Bumper stay
EI-8
REAR BUMPER
A
B
C
D
E
F
G
H
EI
J
K
L
M
MIIB9209E
1. Bumper side bracket 2. Bumper energy shock absorber 3. Rear panel (lower)
4. Bumper fascia 5. Bumper stay
REMOVAL
1. Remove rear combination lamps (LH/RH). Refer to LT-208, "Removal and Installation (Hatchback)" .
2. Remove bumper fascia lower bottom installation clip
3. Remove bumper fascia screws.
EI-9
REAR BUMPER
4. Remove bumper fascia side engaged hooks in the direction
shown by the arrows in the figure.
MIIB0054E
5. Remove license plate lamp, and then pull bumper fascia straight out toward back of vehicle to remove it.
Refer to LT-199, "Removal and Installation of Parking Lamp, Tail Lamp and License Plate Lamp" .
6. Remove bumper energy shock absorber.
7. Remove the engaged rear panel (lower) mounting clips and
hooks, and remove rear panel.
MIIB0055E
8. Remove bolts and bumper stay.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
q Make sure the bumper fascia bottom edge is inserted in the
rear panel (lower) insertion area.
q Rattle will be caused by fitting damaged parts. Following
disassembly, the clipping area under back door should be
checked for damage.
MIIB0056E
EI-10
FRONT GRILLE
FRONT GRILLE PFP:62310
A
Removal and Installation EIS004O1
B
C
D
E
F
G
MIIB0057E
1. Front grille
REMOVAL H
1. Remove mounting clips from top of front grille.
2. Insert your hand between the front grille and radiator core support (upper), and remove the front grille
back hooks in order from the vehicle's center side to its outside. EI
3. After all hooks have been disengaged, pull front grille vehicle center side forward and remove the front
turn signal lamp back insertion area and panel connector to remove the front grille vehicle center side.
J
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION: K
Before engaging the front grille back hooks, make sure the front turn signal lamp back insertion area
is correctly inserted in the inside of the bumper fascia.
L
M
EI-11
FRONT DEFLECTOR
FRONT DEFLECTOR PFP:96015
Removal and Installation EIS004O2
MIIB0058E
1. Front deflector
REMOVAL
1. Remove front bumper. Refer to EI-5, "FRONT BUMPER" in EI section.
2. Remove bolts from front bumper inner side, and then remove front deflector.
INSTALLATION
Install in the reverse order of removal.
EI-12
COWL TOP
COWL TOP PFP:66100
A
Removal and Installation EIS004O3
B
C
D
MIIB0059E
1. Cowl top cover 2. Cowl top seal rubber E
REMOVAL
1. Remove front wiper arms (left and right). Refer to WW-6, "FRONT WIPER AND WASHER SYSTEM" ,
WW-51, "FRONT WIPER AND WASHER SYSTEM (WITH RAIN SENSOR)" in WW section. F
2. Remove mounting screws, and the remove slat covers (LH/RH).
3. Remove cowl top seal rubber.
G
4. Pull cowl top over forward to remove it.
INSTALLATION
Install in the reverse order of removal. H
EI
J
K
L
M
EI-13
FENDER PROTECTOR
FENDER PROTECTOR PFP:63840
Removal and Installation EIS004O4
MIIB9230E
1. Fender protector 2. Fender insulator (if equipped)
EI-14
ROOF SIDE MOLDING
ROOF SIDE MOLDING PFP:73854
A
Removal and Installation EIS004O5
B
C
D
E
F
G
H
EI
MIIB9072E
1. Roof side molding J
REMOVAL
1. Use a plastic knife, etc., and lift up the end of roof side molding (back end), remove clip, and peel off dou-
ble-sided tape to remove it. K
2. Remove the double-sided tape remaining on roof side molding back and vehicle body.
NOTE:
L
Double-sided tape can be easily removed using double-sided tape removal agent.
INSTALLATION
NOTE: M
When only installing roof side molding, conduct the following procedure from Step 3.
1. Clean the roof side molding clip attachment surface (body side).
2. Bond roof side molding clip (body side) to vehicle body and let sit for 40 min.
3. Apply primer (Sumitomo3M N200 or comparable product) to roof side molding back double-sided tape
application area.
4. Apply double-sided tape to roof side molding back (position in figure).
5. After butting roof side molding front end against window seal molding, push in molding from front to back
end, and then affix to body using clips and double-sided tape.
EI-15
WINDSHIELD MOLDING
WINDSHIELD MOLDING PFP:72750
Removal and Installation EIS004O6
MIIB9210E
CAUTION:
Be careful when handling adhesive and primer.
REMOVAL
1. Remove roof finisher (C+C). Refer to EI-37, "Removal and Installation" .
2. Remove cowl top cover. Refer to EI-13, "COWL TOP" .
3. Peel off double-sided tape and remove front fender covers (LH/
RH) from front fenders (LH/RH).
MIIB9073E
4. Apply protective tape along the contour of windshield molding
and cut molding lip with cutter knife.
5. Tear off excess molding from end of molding to glass.
6. With pliers, draw out all the remaining molding left in flanged
area of body to remove it completely from adhering surface on
glass.
MIIB0064E
EI-16
WINDSHIELD MOLDING
INSTALLATION
1. Apply primer between glass and panel then apply enough adhe- A
sive to allow molding adhesion.
NOTE:
q The essential function of primers is to strengthen adhesion B
between glass and painted surface.
q There are 2 types of primer. Never confuse the application meth-
ods. C
Primer M
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo