Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Xterra 2005-2007.2009 Approved Nissan Xterra 2005 SB

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download SB documenatation <<

Text preview - extract from the document

H RESTRAINTS

B
SECTION
SEAT BELTS C

E
CONTENTS
PRECAUTIONS ......................................................... 2
. REMOVAL OF SEAT BELT RETRACTOR - CEN- F
Precautions for Supplemental Restraint System TER ...................................................................... 7
.
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- INSTALLATION OF SEAT BELT RETRACTOR -
SIONER" ................................................................. 2
. CENTER ............................................................... 7
. G
Precautions for Seat Belt Service ........................... 2 . REMOVAL OF SEAT BELT BUCKLE ................... 7 .
AFTER A COLLISION .......................................... 2 . INSTALLATION OF SEAT BELT BUCKLE ........... 7 .
SEAT BELTS ............................................................. 3
. Seat Belt Inspection ................................................. 8
.
SB
Removal and Installation of Front Seat Belt ............ 3 . AFTER A COLLISION .......................................... 8 .
REMOVAL OF SEAT BELT RETRACTOR ........... 4 . PRELIMINARY CHECKS ..................................... 8 .
INSTALLATION OF SEAT BELT RETRACTOR..... 4 SEAT BELT RETRACTOR ON-VEHICLE
REMOVAL OF SEAT BELT BUCKLE ................... 4 . CHECK ................................................................. 9
. I
INSTALLATION OF SEAT BELT BUCKLE ........... 4 . SEAT BELT RETRACTOR OFF-VEHICLE
Removal and Installation of Rear Seat Belt ............ 5 . CHECK ................................................................. 9
.
COMPONENTS ................................................... 5 . LATCH (LOWER ANCHORS AND TETHER FOR J
REMOVAL OF SEAT BELT RETRACTOR - OUT- CHILDREN) SYSTEM .............................................. 11 .
BOARD ................................................................ 7
. Removal and Installation ....................................... 11 .
INSTALLATION OF SEAT BELT RETRACTOR - TOP TETHER STRAP CHILD RESTRAINT ............ 12 .
K
OUTBOARD ......................................................... 7
. Removal and Installation ....................................... 12 .

Revision: February 2006 SB-1 2005 Xterra
PRECAUTIONS

PRECAUTIONS PFP:00001

Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EHS001DH

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
G To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
G Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
G Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Seat Belt Service EHS001DI

CAUTION:
G Before removing the seat belt pre-tensioner assembly, turn the ignition switch OFF, disconnect
both battery cables and wait at least 3 minutes.
G After replacing or reinstalling seat belt pre-tensioner assembly, or reconnecting seat belt pre-ten-
sioner assembly connector, ensure entire SRS operates properly. Refer to SRS-20, "SRS Opera-
tion Check" .
G Do not disassemble buckle or seat belt assembly.
G Do not reuse seat belt anchor bolts after removal. Replace with new ones.
G Replace anchor bolts if they are deformed or worn out.
G Never oil tongue and buckle.
G If any component of seat belt assembly is questionable, do not repair. Replace the whole seat belt
assembly.
G If webbing is cut, frayed, or damaged, replace seat belt assembly.
G When replacing seat belt assembly, use a genuine NISSAN seat belt assembly.
AFTER A COLLISION
WARNING:
G Inspect all seat belt assemblies including retractors and attaching hardware after any collision.
G NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the
collision was minor and the belts show no damage and continue to operate properly. Failure to do
so could result in serious personal injury in an accident. Seat belt assemblies not in use during a
collision should also be replaced if either damage or improper operation is noted. Seat belt pre-
tensioner should be replaced even if the seat belts are not in use during a frontal collision in which
the air bags are deployed.
Replace any seat belt assembly (including anchor bolts) if:
G The seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and
buckles show no damage and continue to operate properly).
G The seat belt was damaged in an accident. (i.e., torn webbing, bent retractor or guide, etc.)
G The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage
or distortion and repair as necessary before installing a new seat belt assembly.
G Anchor bolts are deformed or worn out.
G The seat belt pre-tensioner should be replaced even if the seat belts are not in use during the collision in
which the air bags are deployed.

Revision: February 2006 SB-2 2005 Xterra
SEAT BELTS

SEAT BELTS PFP:86884
A
Removal and Installation of Front Seat Belt EHS001DJ

LHIA0081E

1. Seat belt height adjuster 2. Center pillar 3. Seat belt retractor and belt assembly LH
4. Seat belt pre-tensioner connector 5. Center pillar lower finisher 6. Anchor cover
7. Seat belt buckle 8. D-ring anchor bolt cover 9. D-ring anchor
10. Center pillar upper finisher

Revision: February 2006 SB-3 2005 Xterra
SEAT BELTS

REMOVAL OF SEAT BELT RETRACTOR
CAUTION:
G Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
1. Remove the center pillar upper/lower finishers. Refer to EI-27, "BODY SIDE TRIM" .
2. Remove the seat belt retractor anchor bolts and assembly.
G On RH side, disconnect the seat belt tension sensor.

3. Disconnect the seat belt pre-tensioner electrical connector.
CAUTION:
G For installing/removing seat belt pre-tensioner connector,
insert a thin screwdriver wrapped in tape into the notch, lift
the lock and remove the connector.
G Install the connector with the lock raised, and push the lock
into the connector.

PHIA0341E

INSTALLATION OF SEAT BELT RETRACTOR
Installation is in the reverse order of removal.
G Install the seat belt retractor upper bolt first.
G Ensure that seat belt height adjuster is locked in the lowest position during installation.
REMOVAL OF SEAT BELT BUCKLE
1. Remove the front seat. Refer to SE-10, "Removal and Installation" .
2. Remove screw and seat cushion inner finisher.
3. Remove the anchor bolt and buckle.
4. Disconnect the buckle switch connector from the seat connector.

WHIA0128E

INSTALLATION OF SEAT BELT BUCKLE
Installation is in the reverse order of removal.

Revision: February 2006 SB-4 2005 Xterra
SEAT BELTS

Removal and Installation of Rear Seat Belt EHS001DK

COMPONENTS A
Outboard Seat
B

LHIA0101E

1. Seat belt height adjuster 2. Seat belt retractor and belt assembly 3. Seat belt lower anchor
4. Seat belt buckle 5. D-ring anchor bolt cover 6. D-ring anchor

Revision: February 2006 SB-5 2005 Xterra
SEAT BELTS

Center Seat

LHIA0102E

1. Seat belt retractor and belt assem- 2. Seat belt buckle 3. Finisher
bly
4. Guide plate

Revision: February 2006 SB-6 2005 Xterra
SEAT BELTS

REMOVAL OF SEAT BELT RETRACTOR - OUTBOARD
1. Remove seat belt lower anchor cover and bolt. A
2. Remove the D-ring anchor bolt cover and D-ring anchor bolt.
3. Remove the upper and lower luggage area trim. Refer to EI-27, "BODY SIDE TRIM" .
B
4. Remove seat belt retractor anchor bolt and the seat belt assembly.
5. Remove the seat belt height adjuster assembly.
INSTALLATION OF SEAT BELT RETRACTOR - OUTBOARD C
Installation is in the reverse order of removal.
G Ensure that seat belt height adjuster is locked in the lowest position during installation.
D
REMOVAL OF SEAT BELT RETRACTOR - CENTER
1. Remove headlining. Refer to EI-31, "HEADLINING" .
2. Remove seat belt guide plate bolts.
E
3. Remove seat belt retractor and belt assembly bolt and nut.
4. Remove seat belt retractor cover.
5. Remove bolt and remove seat belt retractor and seat belt assembly. F
INSTALLATION OF SEAT BELT RETRACTOR - CENTER
Installation is in the reverse order of removal.
G
REMOVAL OF SEAT BELT BUCKLE
1. Remove the rear seat cushion. Refer to SE-16, "REAR SEAT" .
2. Remove the anchor bolt and buckle. SB
INSTALLATION OF SEAT BELT BUCKLE
Installation is in the reverse order of removal.
I

Revision: February 2006 SB-7 2005 Xterra
SEAT BELTS

Seat Belt Inspection EHS001DM

AFTER A COLLISION
WARNING:
Inspect all seat belt assemblies including retractors and attaching hardware after any collision.
NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the col-
lision was minor and the belts show no damage and continue to operate properly. Failure to do so
could result in serious personal injury in an accident. Seat belt assemblies not in use during a colli-
sion should also be replaced if either damage or improper operation is noted. Seat belt pre-tensioners
should be replaced even if the seat belts are not in use during a frontal collision in which the air bags
are deployed.
Replace any seat belt assembly (including anchor bolts) if:
G The seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and
buckles show no damage and continue to operate properly).
G The seat belt was damaged in an accident. (i.e. torn webbing, bent retractor or guide).
G The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage
or distortion and repair as necessary before installing a new seat belt assembly.
G Anchor bolts are deformed or worn out.
G The seat belt pre-tensioner should be replaced even if the seat belts are not in use during the collision in
which the air bags are deployed.

PRELIMINARY CHECKS
1. Check the seat belt warning lamp/chime for proper operation as follows:
a. Switch ignition ON. The seat belt warning lamp should illuminate. Also, the seat belt warning chime should
sound for about seven seconds.
b. Fasten driver's seat belt. The seat belt warning lamp should go out and the chime (if sounding) should
stop.
2. If the air bag warning lamp is blinking, conduct self-diagnosis using CONSULT-II, and air bag warning
lamp. Refer to SRS-18, "CONSULT-II Function (AIR BAG)" .
3. Check that the seat belt retractor, seat belt anchor and buckle bolts are securely attached.
4. Check the shoulder seat belt guide and shoulder belt height adjuster for front seats. Ensure guide swivels
freely and that belt lays flat and does not bind in guide. Ensure height adjuster operates properly and
holds securely.
5. Check retractor operation:
a. Fully extend the seat belt webbing and check for twists, tears or other damage.
b. Allow the seat belt to retract. Ensure that belt returns smoothly and completely into the retractor. If the
seat belt does not return smoothly, wipe the inside of the loops with a clean paper cloth, because dirt built
up in the loops of the upper anchors can cause the seat belts to retract slowly.
c. Fasten the seat belt. Check the seat belt returns smoothly and completely to the retractor. If the belt does
not return smoothly, the cause may be an accumulation of dust or dirt. Use the "SEAT BELT TAPE SET"
and perform the following steps.
Inspect the front seat belt through-anchor:
1. Pull the seat belt out to a length of 500 mm (19.69 in) or more.
2. Use a clip or other device to hold the seat belt at the center pillar belt opening.
3. Pass a thin wire through the through-anchor belt opening. Hold both ends of the wire and pull taut while
moving it up and down several times along the belt opening surface to remove dirt.
4. Any dirt that cannot be removed with the wire can be removed by cleaning the opening with a clean
cloth.
5. Apply tape at the point where the belt contacts the through-anchor belt opening.
NOTE:
Apply the tape so that there is no looseness or wrinkling.
6. Remove the clip holding the seat belt and check that the belt returns smoothly.
7. Repeat steps above as necessary to check the other seat belts.

Revision: February 2006 SB-8 2005 Xterra
SEAT BELTS

SEAT BELT RETRACTOR ON-VEHICLE CHECK
Emergency Locking Retractors (ELR) and Automatic Locking Retractors (ALR) A
NOTE:
All seat belt retractors are of the Emergency Locking Retractors (ELR) type. In an emergency (sudden stop)
the retractor will lock and prevent the belt from extending any further. All 3-point type seat belt retractors B
except the driver's seat belt also have an Automatic Locking Retractors (ALR) mode. The ALR mode (also
called child restraint mode) is used when installing child seats. The ALR mode is activated when the seat belt
is fully extended. When the belt is then retracted partially, the ALR mode automatically locks the seat belt in a C
specific position so the belt cannot be extended any further. To cancel the ALR mode, allow the seat belt to
fully wind back into the retractor.
Check the seat belt retractors using the following test(s) to determine if a retractor assembly is operating prop-
erly. D

ELR Function Stationary Check
Grasp the shoulder belt and pull forward quickly. The retractor should lock and prevent the belt from extending E
further.
ALR Function Stationary Check
1. Pull out entire length of seat belt from retractor until a click is heard. F
2. Retract the belt partially. A clicking noise should be heard as the belt retracts indicating that the retractor is
in the Automatic Locking Retractor (ALR) mode.
3. Grasp the seat belt and try to pull out the retractor. The belt must lock and not extend any further. If neces- G
sary replace the retractor assembly.
4. Allow the entire length of the belt to retract to cancel the automatic locking mode.
SB
ELR Function Moving Check
WARNING:
Perform the following test in a safe, open area clear of other vehicles and obstructions (for example, a I
large, empty parking lot). Road surface must be paved and dry. DO NOT perform the following test on
wet or gravel roads or on public streets and highways. This could result in an accident and serious
personal injury. The driver and passenger must be prepared to brace themselves in the event the J
retractor does not lock.
1. Fasten drivers seat belt. Buckle a passenger into the seat for the belt that is to be tested.
2. Proceed to the designated safe area. K
3. Drive the vehicle at approximately 16 km/h (10 MPH). Notify any passengers of a pending sudden stop.
The driver and passenger must be prepared to brace themselves in the event the retractor does not lock.
Apply brakes firmly and make a very hard stop.
L
During stop, seat belts should lock and not be extended. If the seat belt retractor assembly does not lock, per-
form the retractor off-vehicle check.
M
SEAT BELT RETRACTOR OFF-VEHICLE CHECK
1. Remove the seat belt retractor assembly.
2. Slowly pull out belt while tilting the retractor assembly forward from the mounted position without twisting
the retractor assembly as shown in the illustration.
15 degrees or less tilt : Belt can be pulled out.
35 degrees or more tilt : Belt locks and cannot be pulled out.

Revision: February 2006 SB-9 2005 Xterra
SEAT BELTS

LHIA0104E

A Front seat belt (mounted position) B Rear seat belt (mounted position) C Center seat belt (mounted position)
1. 15 degrees or less tilt 2. 35 degrees or more tilt

If the retractor does not operate within specifications, replace the retractor assembly.

Revision: February 2006 SB-10 2005 Xterra
LATCH (LOWER ANCHORS AND TETHER FOR CHILDREN) SYSTEM

LATCH (LOWER ANCHORS AND TETHER FOR CHILDREN) SYSTEM PFP:75466
A
Removal and Installation EHS001DN

NOTE:
The LATCH (Lower Anchors and Tether for Children) system is not serviceable. B

Revision: February 2006 SB-11 2005 Xterra
TOP TETHER STRAP CHILD RESTRAINT

TOP TETHER STRAP CHILD RESTRAINT PFP:88000

Removal and Installation EHS001DO

NOTE:
The Top Tether Strap Child Restraint system is not serviceable.

Revision: February 2006 SB-12 2005 Xterra

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo