Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Xterra 2005-2007.2009 Approved Nissan Xterra 2006 acc
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download acc documenatation <<
Text preview - extract from the document
B ENGINE
A
ACCELERATOR CONTROL SYSTEM
SECTION ACC ACC
C
D
E
CONTENTS
PRECAUTIONS ......................................................... 2
. Components ............................................................ 3
. F
Precautions for Supplemental Restraint System Removal and Installation ......................................... 3
.
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- REMOVAL ............................................................ 3
.
SIONER" ................................................................. 2
. INSTALLATION .................................................... 3
. G
ACCELERATOR CONTROL SYSTEM ..................... 3 . INSPECTION AFTER INSTALLATION ................. 4 .
SERVICE DATA AND SPECIFICATIONS (SDS) ....... 5 .
Accelerator Control .................................................. 5
.
H
ACCELERATOR PEDAL ...................................... 5 .
I
J
K
L
M
Revision: September 2005 ACC-1 2006 Xterra
PRECAUTIONS
PRECAUTIONS PFP:00001
Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EBS00T2P
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
G To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
G Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
G Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Revision: September 2005 ACC-2 2006 Xterra
ACCELERATOR CONTROL SYSTEM
ACCELERATOR CONTROL SYSTEM PFP:18005
A
Components EBS00O3T
ACC
C
D
E
F
G
H
I
WBIA0594E
1. Non-adjustable accelerator pedal assembly J
CAUTION:
G Do not disassemble the accelerator pedal assembly.
G Do not remove the accelerator pedal position sensor from the accelerator pedal bracket. K
G Avoid damage from dropping the accelerator pedal assembly during handling.
G Keep the accelerator pedal assembly away from water.
L
Removal and Installation EBS00O3U
REMOVAL
1. Disconnect the negative battery terminal. M
2. Disconnect the accelerator position sensor electrical connector.
a. Pull the connector lock back to unlock the connector from the
accelerator pedal position sensor as shown.
b. Pull up on the connector to disconnect it from the accelerator
pedal position sensor as shown.
3. Remove the two upper and one lower accelerator pedal nuts.
4. Remove the accelerator pedal assembly.
CAUTION:
G Do not disassemble the accelerator pedal assembly.
G Do not remove the accelerator pedal position sensor LBIA0333E
from the accelerator pedal bracket.
G Avoid damage from dropping the accelerator pedal assembly during handling.
G Keep the accelerator pedal assembly away from water.
INSTALLATION
Installation is in the reverse order of removal.
Revision: September 2005 ACC-3 2006 Xterra
ACCELERATOR CONTROL SYSTEM
INSPECTION AFTER INSTALLATION
G Check that the accelerator pedal moves smoothly within the
specified range.
Accelerator pedal - total pedal : 48 mm (1.89 in)
applied stroke "A"
G Check that the accelerator pedal smoothly returns to the original
position.
G Perform an electrical inspection of the accelerator pedal position
sensor. Refer to EC-611, "DTC P2138 APP SENSOR" .
CAUTION:
When the harness connector of the accelerator pedal posi- LBIA0434E
tion sensor is disconnected, perform Accelerator Pedal
Released Position Learning. Refer to EC-78, "Accelerator Pedal Released Position Learning" .
Revision: September 2005 ACC-4 2006 Xterra
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS) PFP:00030
A
Accelerator Control EBS00O3V
ACCELERATOR PEDAL
Unit: mm (in)
ACC
C
D
E
LBIA0434E
Accelerator pedal - total pedal applied stroke "A" 48 (1.89)
F
G
H
I
J
K
L
M
Revision: September 2005 ACC-5 2006 Xterra
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: September 2005 ACC-6 2006 Xterra
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo