Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Xterra 2000-2004 Approved Nissan Xterra 2003 WW

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download WW documenatation <<

Text preview - extract from the document

K ELECTRICAL

B
SECTION
WIPER, WASHER & HORN C

E
CONTENTS
PRECAUTIONS ......................................................... 2
. REAR WIPER AND WASHER ................................... 9 . F
Precautions for Supplemental Restraint System System Description .................................................. 9 .
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- POWER SUPPLY AND GROUND ....................... 9 .
SIONER" ................................................................. 2
. WIPER OPERATION ............................................ 9 . G
Wiring Diagrams and Trouble Diagnosis ................. 2 . WASHER OPERATION ........................................ 9 .
FRONT WIPER AND WASHER ................................. 3 . AUTO STOP OPERATION ................................... 9 .
System Description ................................................. 3
. Wiring Diagram -- WIP/R -- ................................. 10 .
H
WIPER OPERATION ........................................... 3 . Removal and Installation ....................................... 11 .
WASHER OPERATION ........................................ 4 . WIPER ARM ....................................................... 12 .
Wiring Diagram -- WIPER -- ................................. 5 . Washer Nozzle Adjustment ................................... 12 .
MODELS WITHOUT INTERMITTENT WIPERS 5 ..... Washer Tube Layout ............................................. 13 . I
MODELS WITH INTERMITTENT WIPERS ......... 6 . Check Valve ........................................................... 13
.
Removal and Installation ......................................... 7. CIGARETTE LIGHTER ............................................ 14 .
WIPER ARMS ...................................................... 7
. Wiring Diagram -- CIGAR -- ................................ 14 . J
WIPER MOTOR AND LINKAGE .......................... 7 . HORN ....................................................................... 15
.
Washer Nozzle Adjustment ..................................... 8 . Wiring Diagram -- HORN -- ................................. 15 .
Washer Tube Layout ............................................... 8. WW

WW-1
PRECAUTIONS

PRECAUTIONS PFP:00001

Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EKS0035H

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
q Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harness connec-
tors.
Wiring Diagrams and Trouble Diagnosis EKS0035I

When you read wiring diagrams, refer to the following:
q GI-13, "How to Read Wiring Diagrams"
q PG-8, "POWER SUPPLY ROUTING"
When you perform trouble diagnosis, refer to the following:
q GI-9, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES"
q GI-25, "How to Perform Efficient Diagnosis for an Electrical Incident"
Check for any Service bulletins before servicing the vehicle.

WW-2
FRONT WIPER AND WASHER

FRONT WIPER AND WASHER PFP:28810
A
System Description EKS0035K

WIPER OPERATION
Models Without Intermittent Wipers B
The front wiper switch is controlled by a lever built into the combination switch.
There are two front wiper switch positions:
q LO speed C
q HI speed
With the ignition switch in the ON or START position, power is supplied
q through 20A fuse [No. 6, located in the fuse block (J/B)] D
q to front wiper motor terminal B.
Low and High Speed Wiper Operation
Ground is supplied to front wiper switch terminal 17 through body grounds E12 and E54. E
With the front wiper switch in the LO position, ground is supplied
q to front wiper motor terminal L
q through front wiper switch terminal 14. F
With power and ground supplied, the front wiper motor operates at low speed.
With the front wiper switch in the HI position, ground is supplied
q to front wiper motor terminal H G
q through front wiper switch terminal 16.
With power and ground supplied, the front wiper motor operates at high speed.
Auto Stop Operation H
When the front wiper switch is turned OFF, the front wiper motor will continue to operate at low speed until
wiper blades reach windshield base.
When wiper blades are not located at base of windshield with front wiper switch OFF, ground is supplied I
q to front wiper motor terminal L
q through front wiper switch terminal 14
q through front wiper switch terminal 13 J
q through front wiper motor terminal P
q through front wiper motor terminal E
WW
q through body grounds E12 and E54.
Models With Intermittent Wipers
The front wiper switch is controlled by a lever built into the combination switch. L
There are three front wiper switch positions:
q LO speed
q HI speed M
q INT (Intermittent)
With the ignition switch in the ON or START position, power is supplied
q through 20A fuse [No. 6, located in the fuse block (J/B)]
q to front wiper motor terminal B and
q to front wiper switch terminal 19.
Low and High Speed Wiper Operation
Ground is supplied to front wiper switch terminal 17 through body grounds E12 and E54
With the front wiper switch in the LO position, ground is supplied
q to front wiper motor terminal L
q through front wiper switch terminal 14.
With power and ground supplied, the front wiper motor operates at low speed.
With the front wiper switch in the HI position, ground is supplied
q to front wiper motor terminal H
q through front wiper switch terminal 16.
With power and ground supplied, the front wiper motor operates at high speed.
WW-3
FRONT WIPER AND WASHER

Auto Stop Operation
When the front wiper switch is turned OFF, the front wiper motor will continue to operate at low speed until
wiper blades reach windshield base.
When wiper blades are not located at base of windshield with front wiper switch OFF, ground is supplied
q to front wiper motor terminal L
q through front wiper switch terminal 14
q through front wiper switch terminal 13
q through front wiper motor terminal P
q through front wiper motor terminal E
q through body grounds E12 and E54.
When wiper blades reach base of windshield, front wiper motor terminals B and P are connected instead of
terminals P and E.
Battery power is then supplied
q through front wiper motor terminal P
q to front wiper switch terminal 13.
With battery voltage supplied to front wiper switch terminal 13, the front wiper switch will stop the front wiper
motor with the wiper blades at the PARK position.
Intermittent Operation
The wiper blades perform a single wiping operation, followed by a delay interval which is adjustable from
approximately 3 to 13 seconds, after which the cycle repeats. This feature is controlled by the front wiper
switch.
When the front wiper switch is placed in the INT position, ground is supplied intermittently
q to front wiper motor terminal L
q through front wiper switch terminal 14
q through front wiper switch terminal 17
q through body grounds E12 and E54.
The delay interval time is controlled by the wiper switch.
The wiper motor operates at low speed at the desired delay interval.
WASHER OPERATION
With the ignition switch in the ON or START position, power is supplied
q through 20A fuse [No. 6, located in the fuse block (J/B)]
q to front washer motor terminal +.
When the lever is pulled to the WASH position, ground is supplied
q to front washer motor terminal

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo