Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Forester 1999-2004 Approved Subaru Forester 1999-2000 MECHANICAL COMPONENTS SECTION Wheels and Axles MSA5T0125A27769

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.




Image preview - the first page of the document
MSA5T0125A27769


>> Download MSA5T0125A27769 documenatation <<

Text preview - extract from the document
                                    SERVICE PROCEDURE                                        [W5B0] 4-2
                                                                   5. Replacement of Rear DOJ and BJ Boots


5. Replacement of Rear DOJ                               8) Remove DOJ and BJ boots from drive shaft.
                                                         
and BJ Boots
A: REMOVAL                                               B: INSTALLATION
1) Disconnect ground cable from battery.                 1) Install DOJ and BJ boots to drive shaft.
2) Lift-up vehicle, and remove rear wheel cap and        
wheels.                                                  2) Using ST, install DOJ into differential.
                                                         ST 28099PA090 SIDE OIL SEAL PROTEC-
NOTE:                                                                         TOR
Axle nut need not be removed.
3) Remove ABS sensor clamps and parking brake
cable bracket.
4) Disconnect stabilizer link from lateral link.
5) Remove bolts which secure lateral link assem-
bly to rear housing.
6) Remove bolts which secure trailing link assem-
bly to rear housing.
7) Remove DOJ from rear differential using ST.
ST 28099PA100 DRIVE SHAFT REMOVER
                                                                                                 B4M0549A
NOTE:
The side spline shaft circlip comes out together         3) Insert DOJ spline end into bore of side oil seal,
with the shaft.                                          and remove ST.
                                                         CAUTION:
                                                         Do not allow DOJ splines to damage side oil
                                                         seal.
                                                         ST   28099PA090     SIDE OIL SEAL PROTEC-
                                                                             TOR




                                      S4M0372A

     (1)   Bolt
     (2)   DOJ

CAUTION:
Be careful not to damage side bearing retainer.                                                  B4M0550A
Always use bolt as shown in figure, as support-
ing point for ST during removal.                         4) Align DOJ and differential splines.
                                                         5) Push housing to insert DOJ into differential.
ST     28099PA100        DRIVE SHAFT REMOVER
                                                         NOTE:
                                                         Make sure DOJ is inserted properly.




                                      S4M0373A

     (1)   Side bearing retainer                                                                  G3M0050



                                                    31
4-2   [W6A0]                        SERVICE PROCEDURE
6. Steel Wheel and Tire


CAUTION:                                                 6. Steel Wheel and Tire
Discard old self-locking nut. Replace with a
new one.                                                 A: INSPECTION
6) Connect rear housing assembly to trailing link        1) Deformation or damage on the rim can cause
assembly, and tighten self-locking nut.                  air leakage. Check the rim flange for deformation,
7) Connect rear housing assembly to lateral link         crack, or damage, and repair or replace as neces-
assembly, and tighten self-locking nut.                  sary.
8) Connect stabilizer link to lateral link.              2) Take stone, glass, nail etc. off the tread groove.
9) Install ABS sensor clamps and parking brake           3) Replace tire:
cable bracket.
                                                         CAUTION:
                                                         



◦ Jabse Service Manual Search 2020 ◦ Jabse Pravopis ◦ Other service manual resources online : FixyaeServiceinfo