Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Forester 1999-2004 Approved Subaru Forester 1999-2000 GENERAL INFORMATION SECTION Pre-Delivery Inspection MSA5T0120A27433

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download MSA5T0120A27433 documenatation <<

Text preview - extract from the document

G8040BE1SGML

1-4 [G2A0] PRE-DELIVERY INSPECTION
2. Pre-road Test Inspection

2. Pre-road Test Inspection 2) Release the lock by pushing the lock lever
while pushing the hood down with slight pres-
A: FUSES sure.
CHECK POINTS Hold the hood open with the stay.
1. Fuse installation Check the way the safety lock mechanism is re-
2. Spare fuse leased and that the hood opens and closes
without any abnormal noise and does not con-
Fuse as shown in figure is disconnected to tact the body.
avoid discharging the battery.
Insert fuse (15A) in the main fuse box inside the
engine compartment.
Use fuse indicated by arrow in figure.

S1H0057A

3) Remove the stay and lower the hood until it
approaches about 10 cm (3.9 in.) from the
S1H0055A closed position and let it drop. After closing the
hood, be sure the hood is securely locked.
4) Confirm by repeating the above steps be-
B: HOOD OPERATION ginning with the first one, two or three times.
CHECK POINTS 2. CHECK THE INSTALLATION OF HOOD
1. Operation of hood release and lock
2. Condition of lock After having closed the hood, ensure the hood
3. Fitting of hood fits properly.

1. CHECK THE OPENING, CLOSING AND
LOCKING OF HOOD
1) Pull the hood lock release knob in the pas-
senger compartment. (The hood will lift a step.)
Check if the cable moves easily and lightly with-
out dragging.

S1H0058

NOTE:
D The clearance between the hood and front
fender is uniform.
D The hood's front end is parallel with the front
fender.
S1H0056

4
G8040BE1SGML

PRE-DELIVERY INSPECTION [G2C2] 1-4
2. Pre-road Test Inspection

D The slope of hood is the same as the parts of 2. CHECK THE OPERATION OF DOOR
body surrounding it. LOCKS
D The hood and weatherstrip stick fast to each 1) Close the door completely, lock it with the
other. key plate and pull the outside door handle to en-
sure the door does not open.
C: DOOR, DOOR LOCK AND POWER
WINDOW OPERATION NOTE:
D Do not pull the outside door handle with
CHECK POINTS greater force than necessary.
1. Door "Open-close" operation D While inspecting the door and lock, check the
2. Operation of door release and lock lock in the rear part of the door and the door
3. Loose or damaged parts striker attached to the pillar.
4. Position of door window glass
5. Operation of power window switches
6. Power door locking operation
7. Operation of child safety locks

1. CHECK THE OPENING AND CLOSING OF
DOORS AND REAR GATE
1) First open the door completely by operating
inside door handle and then close it fully by op-
erating the door trim handle from the driver's
seat.
2) Repeat the preceding step two or three
times to see how the door opens and closes. S1H0060A
Pay attention to the operating effort, any abnor-
mal noise and positive operation. 2) Again operate the key plate to ensure the
3) Operate the outside door handle from the door unlocks.
outside and check how the door opens and NOTE:
closes. Also, check that there is a uniform clear- Replace the lock cylinder if it malfunctions.
ance between the door and car body without When the door lock seems to be operating
any grade difference. slowly, lubricate the moving parts with grease or
NOTE: oil.
D To examine the closed state and sinking of 3) Sit in the driver seat, close the door com-
the door, observe from the front right-hand door. pletely, and move the lock lever to the lock posi-
D If the striker drags during opening when the tion. Then, pull the inside door handle to ensure
outside door handle is pulled, adjust by relocat- the door will not open.
ing the striker.

S1H0061A
S1H0059

5
G8040BE1SGML

1-4 [G2C3] PRE-DELIVERY INSPECTION
2. Pre-road Test Inspection

3. CHECK THE LOOSENESS OF DOORS
1) Open and close the door two or three times
with a somewhat strong force.
2) Check the bolts or screws securing the door
hinge, lock and striker for looseness. Retighten
loose ones to the specified tightening torque.
4. CHECK THE OPERATION OF POWER
WINDOW
1) Depress the power window switches to fully
open the windows.
2) Pull up the power window switches to fully S1H0062A
close the windows.
3) Repeat the above steps begginning with the
first one, two or three times to see how the win- D: REAR GATE AND FUEL LID OP-
dows open and close. ERATION
5. CHECK THE OPERATION OF POWER CHECK POINTS
DOOR LOCK 1. Rear gate and fuel lid "open-close"
operation
1) Close the door completely.
2. Operation of rear gate (release and
2) Operate the power door locking switches on
lock)
the front both side doors to lock and check that
3. Fitting of rear gate and fuel lid
all the doors are locked.
3) Operate the power door locking switches on
the front both side doors to unlock and check E: SEAT ADJUSTER AND SEAT
that all the doors are unlocked. BELTS
4) Repeat the above steps two or three times. CHECK POINTS
6. CHECK THE OPERATION OF CHILD 1. Front and rear seats, and their facing
SAFETY LOCKS materials
2. Front seat operation
1) Set the child safety lock on both rear doors 3. Rear seat folding operation
to the lock positions. 4. Seat belts and their fit
2) Close the rear doors completely. 5. Installing procedure for child anchor
3) Check that the lock levers of the rear doors
are in the unlock positions. Then, pull the inside 1. MANUAL THREE-POINT TYPE
door handles of the rear doors to ensure that the
doors will not open. The seat belt warning light on the instrument
4) Next, pull the outside door handles of the panel comes on for approximately six seconds
rear doors to ensure that the doors will open. with the ignition switch "ON".
5) Repeat the above steps two or three times. And the warning chime sounds if the driver's
seat belt is not fastened.
Make sure that the warning system works nor-
mally.

6
G8040BE1SGML

PRE-DELIVERY INSPECTION [G2G1] 1-4
2. Pre-road Test Inspection

2. INSTALLING PROCEDURE FOR CHILD
ANCHOR
CAUTION:
D Be sure to install the upper anchor bracket
assembly in the correct direction.
D Always use the genuine upper anchor
bracket assembly.
When upper anchor bracket assembly is used
for rear seat:
1) For Canada models, the anchor set is inside
the glove box. Take it out and check that its S1H0064A
components are assembled as shown in figure.

F: JACK INSTALLATION
CHECK POINT
1. Installed condition of jack

B1H0089A

2) The anchor installation points are covered
with caps. Remove the cap at the desired an-
chor installation points.
S1H0065A

G: WHEEL NUTS FOR LOOSENESS
AND TIRE INFLATION PRESSURE
CHECK POINTS
1. Wheel nut tightening torque
2. Tire inflation pressure and tire specifi-
cation
3. Damage to tire and rim

S1H0063A
1. CHECK THE WHEEL NUT TIGHTENING
TORQUE
3) Install the anchor at the installation point. Tightening torque:
Tighten the bolt so that the anchor is completely 88

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo