Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Forester 1999-2004 Approved Subaru Forester 2004 2 - Engine Section (H4SO) Engine (Diagnostics) Malfunction Indicator Light
<< Back |
HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download
Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing.
If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download Malfunction Indicator Light documenatation <<Text preview - extract from the document MALFUNCTION INDICATOR LIGHT
ENGINE (DIAGNOSTICS)
16.Malfunction Indicator Light
A: PROCEDURE
1. Activation of malfunction indicator light.
2. Malfunction indicator light does not come on.
3. Malfunction indicator light does not go off.
4. Malfunction indicator light does not blink at a cycle of 3 Hz.
5. Malfunction indicator light remains blinking at a cycle of 3 Hz.
EN(H4SO)-52
MALFUNCTION INDICATOR LIGHT
ENGINE (DIAGNOSTICS)
B: ACTIVATION OF MALFUNCTION 3) If the diagnosis system senses a misfire which
INDICATOR LIGHT could damage the catalyzer, the malfunction indi-
cator light will blink at a cycle of 1 Hz.
1) When the ignition switch is turned to ON (engine
off), the malfunction indicator light (1) in the combi-
nation meter illuminates. (1)
NOTE: (2)
If the malfunction indicator light does not illuminate,
(3)
perform diagnostics of the malfunction indicator
light circuit or the combination meter circuit.
EN-00197
(1) ON
(2) OFF
(3) Ignition switch ON
(4) Engine start
(5) Misfire start
(6) 1 second
4) When the ignition switch is turned to ON (engine
(1) EN-00157 off) or to "START" with test mode connector con-
nected, the malfunction indicator light blinks at a
2) After starting the engine, the malfunction indica-
cycle of 3 Hz.
tor light goes out. If it does not, either the engine or
the emission control system is malfunctioning.
(1)
(1)
(3)
(2)
(4)
(4)
(2)
(3) (3)
(4)
(5)
EN-00198
(6)
EN-00196
(1) ON
(1) No trouble (2) OFF
(2) Trouble occurs (3) Ignition switch ON
(3) ON (4) 1 second
(4) OFF
(5) Ignition switch ON
(6) Engine start
EN(H4SO)-53
MALFUNCTION INDICATOR LIGHT
ENGINE (DIAGNOSTICS)
C: MALFUNCTION INDICATOR LIGHT DOES NOT COME ON.
DIAGNOSIS:
The malfunction indicator light circuit is open or shorted.
TROUBLE SYMPTOM:
When the ignition switch is turned ON (engine OFF), malfunction indicator light does not come on.
WIRING DIAGRAM:
IGNITION
B72 BATTERY
SWITCH
No.14 SBF-4 SBF-1
4 1
B36
5
i1
B9
A1
i3
COMBINATION
17
METER B38
A: i12
28
C: i10
B134 ECM
B72 B134 B38
1 2 3 4 5 6 7 8
1 2 1 2 3 4 5 6 7 8 9
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
3 4 10 11 12 13 14 15 16 17 18 19 20 21
24 25 26 27 28 29 30 31 32 33 34 35
22 23 24 25 26 27 28 29 30 31 32
i10 B36 i12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12 13 14 15 16 17 18 19 20 21 22 23 24 7 8 9 10 11 12 13 14
EN-02055
EN(H4SO)-54
MALFUNCTION INDICATOR LIGHT
ENGINE (DIAGNOSTICS)
Step Check Yes No
1 CHECK OUTPUT SIGNAL FROM ECM. Is the voltage less than 1 V? Go to step 4. Go to step 2.
1) Turn the ignition switch to ON.
2) Measure the voltage between ECM con-
nector and chassis ground.
Connector & terminal
(B134) No. 28 (+) -- Chassis ground (-):
2 CHECK POOR CONTACT. Does the malfunction indicator Repair poor con- Go to step 3.
Check poor contact by shaking or pulling ECM light illuminate? tact in ECM con-
connector and harness. nector.
3 CHECK ECM CONNECTOR. Is the ECM connector correctly Replace the ECM. Repair connection
Check the ECM connector connection. connected?
4 CHECK HARNESS BETWEEN COMBINA- Is the resistance less than 1 Go to step 5. Repair harness
TION METER AND ECM CONNECTOR. ? and connector.
1) Turn the ignition switch to OFF. NOTE:
2) Remove the combination meter. the following:
3) Disconnect the connector from ECM and
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo