Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Legacy 2000-2003 Approved Subaru Legacy 2000 2000 Service Manual BODY SECTION Seats, Seat Belts and Interior MSA5TCD00L16002
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download MSA5TCD00L16002 documenatation <<
Text preview - extract from the document
SERVICE PROCEDURE [W5A2] 5-3
5. Inner Trim Panel
5. Inner Trim Panel 2. REAR SECTION (SEDAN BODY)
1) Removal order of trim panel is as follows:
A: REMOVAL AND INSTALLATION (1) Remove rear mole (K).
1. FRONT SECTION (SEDAN BODY) (2) Remove rear shelf trim.
(1) Remove front mole (H). (3) Remove side sill rear upper cover (F).
(3) Remove front pillar lower trim (C). (4) Remove rear pillar lower trim (J).
(4) Remove side sill front lower cover (D). (5) Remove rear pillar upper trim (I).
(5) Remove rear seat cushion , then remove side sill rear upper
cover (F).
(6) Remove side sill rear lower cover (G).
(7) Remove center pillar lower trim (E).
(8) Detach front seat belt shoulder anchor
, then remove center pil-
lar upper trim (B).
B5M0806A
2) Installation is in the reverse order of removal.
CAUTION:
Be sure to securely hook pawls of inner trim
panel on body flange.
NOTE:
When installing rear quarter upper trim, be sure to
B5M0655A set rear mole as shown in figure.
2) Installation is in the reverse order of removal.
CAUTION:
Be sure to securely hook pawls of inner trim
panel on body flange.
NOTE:
When installing center pillar upper trim and front
pillar upper trim, be sure to set front mole as shown
in figure.
B5M0673A
B5M0673A
21
5-3 [W5A3] SERVICE PROCEDURE
5. Inner Trim Panel
3. FLOOR SECTION (SEDAN BODY) 4. ROOF TRIM (SEDAN BODY)
1) Removal order of floor mat is as follows: 1) Remove sunvisor while disconnecting connec-
(1) Remove front seats. tor and assist rail.
(2) Remove rear seat cushion. 2) Remove front pillar upper trim, center pillar
(3) Remove console box, depending on the upper trim and rear pillar upper trim.
specifications. 3) Remove sunroof garnish. (with sunroof vehicle)
(4) Remove front pillar lower trim panel. 4) Using ST, remove clips (A).
(5) Remove center pillar lower trim panel. ST 925580000 PULLER
(6) Remove side sill rear upper cover.
(7) Remove clips from floor mat.
NOTE:
When pulling out edge, do not pull mat alone; pull
mat together with edge. Pry off two steel clips on
side sill front cover and one on side sill rear cover
using screwdriver.
(8) Remove mat hook.
(9) Remove mat from toe board area.
(10) Remove mat from rear heater duct.
B5M0807A
(11) Roll mat, then take it out of opened rear
door. 5) Installation is in the reverse order of removal.
CAUTION:
When removing clip, use great care to prevent
damaging the roof trim.
5. TRUNK TRIM (SEDAN BODY)
1) Remove clips, then detach trunk rear trim (A).
2) Remove luggage hook (B) and clips, then
detach trunk side trim (C).
S5M0240
(12) Installation is in the reverse order of
removal.
NOTE:
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo