Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Legacy 2000-2003 Approved Subaru Legacy 2000 2000 Service Manual WIRING DIAGRAM Wiring Diagram MSA5TCD00L16081

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download MSA5TCD00L16081 documenatation <<

Text preview - extract from the document

6-3 [D2B4] WIRING DIAGRAM
3. Working Precautions

4. HOW TO DETERMINE A SHORT 3. Working Precautions
CIRCUIT
1) Test lamp method:
A: PRECAUTIONS WHEN WORKING
Connect a test lamp (rated at approximately 3 WITH THE PARTS MOUNTED ON
watts) in place of the blown fuse and allow current THE VEHICLE
to flow through the circuit. Disconnect one connec-
tor at a time from the circuit, starting with the one 1) When working under a vehicle which is jacked-
located farthest from the power supply. If the test up, always be sure to use safety stands.
lamp goes out when a connector is disconnected, 2) The parking brake must always be applied dur-
the wiring between that connection and the next ing working. Also, in automatic transmission
connector (farther from the power supply) is vehicles, keep the select lever set to the P (Park-
shorted. ing) range.
3) Be sure the workshop is properly ventilated
when running the engine. Further, be careful not to
touch the belt or fan while the engine is operating.
4) Be careful not to touch hot metal parts, espe-
cially the radiator and exhaust system immediately
after the engine has been shut off.

B: PRECAUTIONS IN TROUBLE
DIAGNOSIS AND REPAIR OF
ELECTRIC PARTS
G6M0210
1) The battery cable must be disconnected from
2) Ohmmeter method: the battery's (-) terminal, and the ignition switch
Disconnect all affected connectors, and check con- must be set to the OFF position, unless otherwise
tinuity between each connector and ground. When required by the diagnostics.
ohmmeter indicates continuity between a particular 2) Securely fasten the wiring harness with clamps
connector and ground, that connector is shorted. and slips so that the harness does not interfere
with the body end parts or edges and bolts or
screws.
3) When installing parts, be careful not to catch
them on the wiring harness.
4) When disconnecting a connector, do not pull
the wires, but pull while holding the connector
body.

G6M0211

G6M0212

8
WIRING DIAGRAM [D3B0] 6-3
3. Working Precautions

5) Some connectors are provided with a lock. One 6) When checking continuity between connector
type of such a connector is disconnected by push- terminals, or measuring voltage across the termi-
ing the lock, and the other, by moving the lock up. nal and ground, always contact tester probe(s) on
In either type the lock shape must be identified terminals from the wiring connection side. If the
before attempting to disconnect the connector. probe is too thick to gain access to the terminal,
To connect, insert the connector until it snaps and use "mini" test leads.
confirm that it is tightly connected. To check water-proof connectors (which are not
accessible from the wiring side), contact test
probes on the terminal side being careful not to
bend or damage the terminals.

G6M0214

7) Sensors, relays, electrical unit, etc., are sensi-
tive to strong impacts.
Handle them with care so that they are not dropped
or mishandled.

G6M0213

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo