Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Land Cruiser 1986.1998-2007 Approved 98-07 Brake

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document
Brake

>> Download Brake documenatation <<

Text preview - extract from the document

BR-4
BRAKE - BRAKE FLUID

BRAKE FLUID BR12E-07

BLEEDING
HINT:
z If any work is done on the brake system or if air in the
brake lines is suspected, bleed the air from the system.
z When bleeding, keep the amount of the fluid within the
line of reservoir between Min. and Max.
NOTICE:
z Do not let brake fluid remain on painted surfaces.
Wash it off immediately.
z With the reservoir cap removed, when depressing the
brake pedal, the fluid will spray.
1. FILL RESERVOIR WITH BRAKE FLUID
Fluid: SAE J1703 or FMVSS NO. 116 DOT3
2. In case of using TOYOTA hand-held tester:
BLEED HYDRAULIC BRAKE BOOSTER
HINT:
If the hydraulic brake booster has been disassembled, discon-
nect the brake line from the hydraulic brake booster or if the res-
ervoir becomes empty, bleed the hydraulic brake booster.
(a) Turn the ignition switch OFF, depress the brake pedal
more than 40 times.
HINT:
When a pressure in power supply system is released, reaction
force becomes light and stroke becomes longer.
(b) Turn the ignition switch ON, check that the pump stops af-
ter approx. 30 to 40 sec.
NOTICE:
When the pump does not stop, repeat step (a) and (b) again.
(c) With the ignition switch remained ON, depress the brake
pedal more than 20 times.
(d) Observe the procedure in step 4 and bleed the right and
left front brake caliper.
(e) Holding the brake pedal depressed, bleed the right and
left rear brake caliper.
HINT:
It is not necessary to depress the pedal continuously, as brake
fluid flows out by first depressing.

TOYOTA (f) Connect TOYOTA hand-held tester.
Hand-held (1) Turn the ignition switch OFF, connect the TOYOTA
Tester hand-held tester to DLC3.
(2) Turn the ignition switch ON and select "AIR BLEED-
ING" on the TOYOTA hand-held tester.
HINT:
Please refer to the TOYOTA hand-held tester operator's manu-
al for further details.
DLC3
F06425

2004 LAND CRUISER (RM1071U)

Author : Date : 2140
BR-5
BRAKE - BRAKE FLUID

(g) Bleed right front brake line.
(1) Select "FR LINE" on the TOYOTA hand-held tester.
(2) With "FR LINE" turned ON with the TOYOTA hand-
held tester, depress the brake pedal and hold it to
bleed the right front brake caliper.
(3) Repeat step (2) until there are no more air bubbles
in the fluid.
(h) Bleed left front brake line.
(1) Select "FL LINE" on the TOYOTA hand-held tester.
(2) With "FL LINE" turned ON with the TOYOTA hand-
held tester, depress the brake pedal and hold it to
bleed the left front brake caliper.
(3) Repeat step (2) until there are no more air bubbles
in the fluid.
(i) w/ ABS & TRAC & VSC only:
Bleed rear brake line.
(1) Select "RR LINE" on the TOYOTA hand-held tester.
(2) With "RR LINE" turned ON with the TOYOTA hand-
held tester, bleed the left and right rear brake cali-
per.
(j) Disconnect the TOYOTA hand-held tester from DLC3.
(k) Clear the DTC (See page DI-505 ).
3. In case of using ABS actuator checker (SST):
BLEED HYDRAULIC BRAKE BOOSTER
HINT:
If the hydraulic brake booster has been disassembled, discon-
nect the brake line from the hydraulic brake booster or if the res-
ervoir becomes empty, bleed the hydraulic brake booster.

w/ ABS Only: (a) Disconnect the 2 connectors from the hydraulic brake
booster.

w/ ABS & BA & TRAC & VSC Only:

F04459
F09169
F09632

2004 LAND CRUISER (RM1071U)

Author : Date : 2141
BR-6
BRAKE - BRAKE FLUID

(b) Connect the actuator checker (SST) to the hydraulic
brake booster side wire harness via the sub-wire harness
(SST), as shown in the chart below.
SST 09990-00150, 09990-00480
HINT:
Connect the connector with the label of "AIR BLEED" attached
to the connector of actuator checker.
(c) Connect the red cable of the checker to the battery posi-
tive (+) terminal and the black cable to the negative (-) ter-
minal.

Sub-wire Harness S (SST)

AIR BLEED

FRONT

Hydraulic Brake
Booster
REAR

F02821

(d) Turn the ignition switch OFF, depress the brake pedal
more than 40 times.
HINT:
When a pressure in power supply system is released, reaction
force becomes light and stroke becomes longer.
(e) Turn the ignition switch ON, check that the pump stops af-
ter 30 to 40 sec.
NOTICE:
When the pump does not stop, repeat step (d) and (e) again.
(f) With the ignition switch remained ON, depress the brake
pedal more than 20 times.
(g) Observe the procedure in step 4 and bleed the right and
left front wheel caliper.
(h) Holding the brake pedal depressed, bleed the right and
left rear brake caliper.
HINT:
It is not necessary to depress the pedal continuously, as brake
fluid flows out by first depressing.

2004 LAND CRUISER (RM1071U)

Author : Date : 2142
BR-7
BRAKE - BRAKE FLUID

(i) Bleed right front brake line.
(1) Turn the selector switch of the actuator checker to
the "FRONT RH" position.
(2) Push and hold in MAIN push switch, depress the
brake pedal and hold it to bleed the right front brake
caliper.
NOTICE:
Do not keep the MAIN switch pushed in for more than 10
F02823 sec. When operating it continuously, set the interval of
more than 20 sec.
(3) Repeat step (2) until there are no more air bubbles
in the fluid.

(j) Bleed left front brake line.
(1) Turn the selector switch of the actuator checker to
the "FRONT LH" position.
(2) Push and hold in the MAIN push switch, depress the
brake pedal and hold it to bleed the left front brake
caliper.
NOTICE:
Do not keep the MAIN switch pushed in for more than 10
F02824 sec. When operating it continuously, set the interval of
more than 20 sec.
(3) Repeat step (2) until there are no more air bubbles
in the fluid.

(k) w/ ABS & TRAC & VSC only:
Bleed right rear brake line.
(1) Push and hold in the "SUB LH" and "SUB RH"
switches, bleed the right rear brake caliper.
NOTICE:
Do not keep the MAIN switch pushed in for more than 10
sec. When operating it continuously, set the interval of
more than 20 sec.
F02825 (2) Repeat step (1) until there are no more air bubbles
in the fluid.
2004 LAND CRUISER (RM1071U)

Author : Date : 2143
BR-8
BRAKE - BRAKE FLUID

(l) Observe the procedure in step (k) and bleed left rear
brake line.
(m) Disconnect the actuator checker (SST) and sub-wire har-
ness (SST) from the actuator.
SST 09990-00150, 09990-00480
(n) Connect the 2 connectors to the hydraulic brake booster.
(o) Clear the DTC (See page DI-505 ).

4. BLEED BRAKE LINE
(a) Connect the vinyl tube to the brake caliper.
(b) Depress the brake pedal several times, then loosen the
bleeder plug with the pedal held down.
(c) At the point when fluid stops coming out, tighten the
bleeder plug, then release the brake pedal.
(d) Repeat (b) and (c) until all the air in the fluid has been bled
out.
F04458 (e) Repeat the above procedure to bleed the brake line for
each wheel.
Torque: 11 N

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo