Service Manuals, User Guides, Schematic Diagrams or docs for : Akai DV DV-P4990KDSM DV-P4990KDSM
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download DV-P4990KDSM documenatation <<
Text preview - extract from the document
DVD PLAYER
Model:
DVP4990KDSM
SERVICE MANUAL
www.akai.ru
1. General Section
1.1 Cautions/Warnings
1.1.1 Product Safety Notice
Parts marked with the symbol in the schematic diagram have critical char-
acteristics.
Use ONLY replacement pares recommended by the manufacturer.
It is recommended that the unit be operated from a suitable DC supply or batter-
ies during initial check out procedures.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING HIGH VOLTAGE INSIDE TO PREVENT
ELECTRICAL SHOCK DO NOT REMOVE ANY CO-
VER OR SCREW. REFER ALL SERVICING TO QU-
ALIFIED SERVICE PERSONNEL. DO NOT ALLOW
THIS PRODUCTION BE EXPOSED TO RAIN OR
MOISTURE. DISCONNECT THIS MAINS PLUG
FROM THE SUPPLY SOCKET WHEN NOT IN
USE.
1.1.2 Leakage Current Check/Resistance Check
Before returning the unit to the customer, make sure you make either (1) a
leakage current check or (2) a line to insulated resistance check.
If the leakage current exceeds 0.5 milliamps , or if the resistance from chas-
sis to either side of the power cord is less than 240 K ohms, the unit is defec-
tive.
WARNING: DO NOT return the unit to the customer until the problem or loca-
ted and corrected.
1.2. Safe Warnings
1.2.1. Protection of Eyes from Laser Beam
To protect eyes from invisible laser beam during servicing
DO NOT LOOK AT THE LASER BEAM
Page 2
1.2.2 Laser Caution
CAUTION
Adjusting the knobs, switches, and controls , ect. Or taking actions not
specified herein may result in a harmful emission of laser beams.
This CD Changer must be adjusted and repaired only by qualified serv ice
personnel.
CAUTION- INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS
DEFEATED AVOID EXPOSURE TO BEAM.
VORSICHTI- UNSICHTBARE LASERSTRAHLUNG TRITT AUS. WENN DECKEL
GEOFFNET UND WENN SICHERHEITSVERRIEGELUNG
uBERBRuCKT IST. NICHT DEM STRAHL AUSSETZENI
VARNING- OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD OCH
SPARR AR URKOPPLAD STRALEN AR FARLIG.
ADVARSEL-USYNLIG LASERSTRALING VED ABNING NAR
SIKKERHEADSAFBRYDERE ER UDE AF FUNKTION. UNDGA
UDSAETTELSE FOR STRALING.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
THIS IS COMPACT DISC PLAYER IS CLASSIFIED AS A CLASS LASER
PRODUCT.
THE LASS 1 LASER PRODUCT LABEL IS LOCATED ON THE REAR EX-
TERIOR.
1.3. Precautions
1.3.1. ESD Precautions in Repairing
1.3.1.1 Do not apply excessive pressure on the mechanical parts (movi-
ng pares), including the Pickup Block, as extremely high mechanical pre-
cision or required in these parts.
1.3.1.2 When soldering the microprocessor and signal processing IC s,
use a ceramic soldering iron or a soldering iron whose metal part is grou-
nded since they are not resistant to static electricity.
1.3.1.3 When removing the solder or soldering the laser shorting lands
for the Pickup Block, use a ceramic soldering iron or a soldering iron wh-
ose metal part is grounded since the laser diode or not resistant to static
electricity.
Page 3
1.3.2. DVD Loading Unit Precautions When handing the
Mechanism Block
1.3.2.1 Do not loosen any screws in the Pickup Block.
1.3.2.2 Do not adjust any screws in the Mechanism Block except for
Tilt Adjust Screws , as they are adjusted precisely at the factory.
1.3.2.3 Replacement of the Pickup Block is impossible. Always repl-
ace the Traverse Ass s when the Pickup Block needed to be replace .
Do not touch the lens or lens holder of the Pickup Block.
1.3.2.4 The Guide Rails of the Pickup Block are greased. Take care wh-
en handing.
1.3.2.5 When you try to slide the Pickup Block, do not press or pull it
directly, Always turn the dive gears with your fingers.
1.3.2.6 Be sure that the anti-slipping rubber on the turnable or clean.
If there is dust or it is greasy,clean the part with the liquid that contains
50% each of alcohol and water.
1.3.2.7 When removing the Mechanism P.C.B. Ass s, you need to sho-
rt-circuit the laser diode shorting lands beforehand.
1.4. Software Upgrade
You can upgrade DVD player using the software we provide as following step:
The CD-R update is below lists:
First, burn CDR for upgrade. Dummy files are needed minimum 20Mbytes.
The burning software is Nero burning soft:
1. Volume name: MTK
2. Files name and type: MEDIATEK .BIN ( This file must locate Root directory)
3. CD-R burn type(formate): ISO9660
Model 1
ISO1 (level 1)
don t choice Jolient
don t choice loosen ISO strict
Notice: MTK and MEDIATEK .BIN are upper case.
The CD upgrade process:
After the servo read the CD-R data ,Show Message on TV :
UPGRADE FILE DETECTED
UPGRADE ?
PRS CHOOSE (1-8Bit 2-16Bit)
Page 4
Press 1 key , Show Message on TV
UPGRADE FILE DETECTED
UPGRADE ?
File Copy
The tray is automatic to open, take disc away.
UPGRADE FILE DETECTED
UPGRADE ?
Upgrading
At this time, please wait a few minutes, DVD is downloading code to flash, After
Logo will be show on TV again, the update process finish.
Notice: During upgrading , don s turn off power.
Displaying the software Version Number
After opening the tray, press the following keys on the remote control ,
DISPLAY (Up) (Down) (Left) (Right)
then the software version number appears.
Page 5
MPEG Circuit Diagram and Component Layout
Page 6
MPEG Circuit Diagram and Component Layout
Page 7
MPEG Circuit Diagram and Component Layout
Page 8
MPEG Circuit Diagram and Component Layout
Page 9
MPEG Circuit Diagram and Component Layout
Page 10
POWER Circuit Diagram
POWER Circuit Top silk
POWER Circuit Bottom silk
Page 11
SCART PCB Diagram
Karaoke Circuit PCB Diagram
Page 12
3.2. Read Disc Trouble Service Flow Chart
Read disc problem in a DVD player is a very complicated issue that may involve
complex issues. This problem is not only relation to the electronic circuit, but
also very much relation to the operation environment.
DVD loading unit is a very complicate part that contains big number of ESD com-
ponents , which require specific equipment, tools and technique to repair; In ge-
neral, service technician is not suggested to disassemble the DVD loading unit.
It is suggest proving the trouble and replacing the complete DVD loading unit, in-
stead of repairing the DVD loading unit in local workshop.
It is suggested to prove the faulty of a DVD loading unit by replacement by a good
DVD loading unit.
Before checking the NO DISC Trouble, ensure excluding the following possi-
bilities:
The test disc is damage.
AC power supply voltage dropped below the minimum required level.
DVD disc region code and color system is not matching to the DVD player or
system setting.
Moisture condensed inside the unit. (Power on the unit, without disc loaded,
for 1 / 2 to 2 hours).
Service Flow Chart
Read DISC Trouble
Check DVD LOADER NG
Replace Connector
Connector Condition
OK
Replace DVD Loading Unit
NG
Check the MPEG ATAPI Check the other Parts by
I/F Interface Circuit Replacement Method
Page13
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo