Service Manuals, User Guides, Schematic Diagrams or docs for : EmbeddedArtists LPCXpresso_Base_Board_revB1
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download LPCXpresso_Base_Board_revB1 documenatation <<
Text preview - extract from the document
Page 2
LPCXpresso connector and Reset
Page 3
Expansion connectors
Page 4
Optional LPC1xxx and JTAG connectors
Page 5
USB, CAN, ETH, RS422/485 interfaces
Page 6
Direct digital I/O peripherals
Page 7
Analog peripherals
Rev B1
Page 8 Changed to generic pin naming since many different
LPCXpresso target boards exist.
I2C peripherals
Rev B
Added J60/J61/R216/R217 (page 5) for USB Host i/f.
Page 9 Added J62 (page 6) to support LPC17xx bootload.
Added J58 (page 10) to support spi i/f to OLED or mbed.
SPI peripherals
Rev A
First rev
Page 10
Shared SPI/I2C peripherals
UL = UnLoaded = normally not mounted component.
Page 11
Default jumper settings are indicated in the schematic.
USB-to-UART bridge, RF-module, power supply
However, always check jumper positions on actual boards
since there is no guarantee that all jumpers are in default place.
+3V3
Reset generation C1
100nF
U1
CAT811S
GND
VCC 4
1 3 3 MR# RESET# 2
2 4 1
LPCXpresso and mbed connector GND
+3V3
+3V3
SHIELD SW1
PUSHBUTTON
Battery Holder (pin naming follow LPCXpresso module) GND
470R
GND GND
10K
Note: battery not included!
R1
R2
+3V3
Note: battery will quickly drain
+3V3
U2G$1
LED1
D1
RED
since complete board is powered via D2. LOCAL_3V3 74LVC1G125GW
1
5
PMEG2010AEH (or PMEG1020EA) R3
VCC
Battery powering only included 2 4 GPIO_0-RESET
for demonstration purpose.
Current measurement U2G$2 270R
GND
GND
J1 2 2
+
3
CR2032H 1 Default for J2 1 Default for J3
J2 J3
-
D2 GND
GND 4448
mbed module LPCXpresso LPCXpresso
LPC1768 LPC1343/1114
Dual row holes (2x27), 100 mil spacing LPCXpresso
LPC1343/1114
LPCXpresso
LPC1768
mbed module
GND GND GND GND J4-1 J4-28 VOUT (+3.3V out) if self powered, VOUT (+3.3V out) if self VOUT (3.3V out)
else +3.3V input powered, else +3.3V input
VIN (4.5-5.5V) VIN (4.5-5.5V) VIN (4.5-5.5V) VIN J4-2 J4-29 not used not used VU (5.0V USB out)
VB (battery supply) VB (battery supply) not used VBAT J4-3 J4-30 not used not used IF+
nR (reset) RESET_N Reset / PIO0_0 GPIO_0-RESET J4-4 J4-31 not used not used IF-
SPI1-MOSI P0.9 MOSI1 PIO0_9 / MOSI / CT16B0_MAT1 / SWO GPIO_1-MOSI J4-5 ETH_RXN J4-32 not used RD- RD- (Ethernet)
SPI1-MISO P0.8 MISO1 PIO0_8 / MISO/CT16B_MAT0 GPIO_2-MISO J4-6 ETH_RXP J4-33 not used RD+ RD+ (Ethernet)
SPI1-SCK P0.7 SCK1 PIO2_11 / SCK GPIO_3-SCK J4-7 ETH_TXN J4-34 not used TD- TD- (Ethernet)
GPIO P0.6 SSEL1 PIO0_2 / SSEL / CT16B0_CAP0 GPIO_4 J4-8 ETH_TXP J4-35 not used TD+ TD+ (Ethernet)
UART1-TX / I2C1-SDA P0.0 TXD3/SDA1 PIO1_7 / TXD / CT32B0_MAT1 GPIO_5-TXD J4-9 USB_DM J4-36 USB_DM PIO2_4 USB-D- D- (USB)
for LPC1114
UART1-RX / I2C1-SCL P0.1 RXD3/SCL1 PIO1_6 / RXD / CT32B0_MAT0 GPIO_6-RXD J4-10 USB_DP J4-37 USB_DP PIO2_5 USB-D+ D+ (USB)
for LPC1114
SPI2-MOSI P0.18 MOSI0 PIO0_7 / CTS GPIO_7 J4-11 GPIO_24-BL_EN J4-38 PIO0_1 / CLKOUT / P0.4 CAN_RX2 CAN-RD
CT32B0_MAT2 / USB_FTOGGLE
SPI2-MISO P0.17 MISO0 PIO2_0 / DTR GPIO_8 J4-12 GPIO_25-VBUS J4-39 PIO0_3 / USB_VBUS P0.5 CAN_TX2 CAN-TD
SPI2-SCL / UART2-TX P0.15 TXD1/SCK0 PIO2_1 / DSR GPIO_9 J4-13 GPIO_26-SDA J4-40 PIO0_5 / SDA P0.10 TXD2/SDA2 UART3-TX / I2C2-SDA
UART2-RX P0.16 RXD1/SSEL0 PIO2_2 / DCD GPIO_10 J4-14 GPIO_27-SCL J4-41 PIO0_4 / SCL P0.11 RXD2/SCL2 UART3-RX / I2C2-SCL
AIN0 P0.23 AD0.0 TDI / PIO0_11 / AD0 / CT32B0_MAT3 GPIO_11 J4-15 GPIO_28 J4-42 PIO1_9 / CT16B1_MAT0 P2.0 PWM1.1 PWMOUT0
AIN1 P0.24 AD0.1 TMS / PIO1_0 / AD1 / CT32B1_CAP0 GPIO_12 J4-16 GPIO_29 J4-43 PIO1_10 / AD6 / CT16B1_MAT1 P2.1 PWM1.2 PWMOUT1
AIN2 P0.25 AD0.2 TDO / PIO1_1 / AD2 / CT32B1_MAT0 GPIO_13 J4-17 GPIO_30 J4-44 PIO1_11 / AD7 P2.2 PWM1.3 PWMOUT2
AIN3 / AOUT P0.26 AD0.3/AOUT TRST / PIO1_2 / AD3 / CT32B1_MAT1 GPIO_14 J4-18 GPIO_31 J4-45 PIO2_3 / RI P2.3 PWM1.4 PWMOUT3
AIN4 P1.30 AD0.4 SWDIO / PIO1_3 / AD4 / CT32B1_MAT2 GPIO_15 J4-19 GPIO_32 J4-46 PIO2_4 PIO3_4 P2.4 PWM1.5 PWMOUT4
for LPC1114
AIN5 P1.31 AD0.5 PIO1_4 / AD5 / CT32B1_MAT3 / WAKEUP GPIO_16-WAKEUP J4-20 GPIO_33 J4-47 PIO2_5 PIO3_5 P2.5 PWM1.6 PWMOUT5
for LPC1114
P0.2 PIO1_5 / RTS / CT32B0_CAP0 GPIO_17 J4-21 GPIO_34 J4-48 PIO2_6 P2.6
P0.3 PIO1_8 / CT16B1_CAP0 GPIO_18 J4-22 GPIO_35 J4-49 PIO2_7 P2.7
P0.21 PIO0_6 / USB_CONNECT / SCK GPIO_19-USB_CONNJ4-23 GPIO_36 J4-50 PIO2_8 P2.8
P0.22 SWCLK / PIO0_10 / SCK / CT16B0_MAT2 GPIO_20 J4-24 GPIO_37 J4-51 PIO2_9 P2.10
P0.27 PIO3_0 GPIO_21 J4-25 GPIO_38 J4-52 PIO2_10 P2.11
P0.28 PIO3_1 GPIO_22 J4-26 GPIO_39 J4-53 PIO3_3 P2.12
P2.13 PIO3_2 GPIO_23 J4-27 GND J4-54 GND GND
Note: Pins between rows are not connected (for example on LPC176x and LPC1227).
Note: See User's Manual for information about pinning for all different LPCXpresso target boards!
Expansion Connector
+3V3
1 2
3 4
GPIO_0-RESET R4 270R 5 6 R5 270R GPIO_24-BL_EN
GPIO_4 R6 270R 7 8 R7 270R GPIO_25-VBUS
GPIO_27-SCL R8 270R 9 10 R9 270R GPIO_26-SDA
GPIO_19-USB_CONN R10 270R 11 12 R11 270R GPIO_7
GPIO_2-MISO R12 270R 13 14 R13 270R GPIO_1-MOSI
GPIO_20 R14 270R 15 16 R15 270R GPIO_11
GPIO_12 R16 270R 17 18 R17 270R GPIO_13
GPIO_14 R18 270R 19 20 R19 270R GPIO_15
GPIO_16-WAKEUP R20 270R 21 22 R21 270R GPIO_17
GPIO_6-RXD R22 270R 23 24 R23 270R GPIO_5-TXD
GPIO_18 R24 270R 25 26 R25 270R GPIO_28
GPIO_29 R26 270R 27 28 R27 270R GPIO_30
GPIO_8 R28 270R 29 30 R29 270R GPIO_9
GPIO_10 R30 270R 31 32 R31 270R GPIO_31
GPIO_32 R32 270R 33 34 R33 270R GPIO_33
GPIO_34 R34 270R 35 36 R35 270R GPIO_35
GPIO_36 R36 270R 37 38 R37 270R GPIO_37
GPIO_38 R38 270R 39 40 R39 270R GPIO_3-SCK
GPIO_21 R40 270R 41 42 R41 270R GPIO_22
GPIO_23 R42 270R 43 44 R43 270R GPIO_39
45 46
47 48
VIN 49 50 VBAT
J5
GND
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
35 36
37 38
39 40
41 42
43 44
45 46
47 48
49 50
J6
GND
Expansion Connector for Breadboard
Optional LPC1114/LPC1343 for standalone boards
(placed inbetween LPCXpresso/mbed connector)
U3
LPC1113/LPC1343
3 GPIO_0-RESET
JTAG connectors
RESET/PIO0_0
PIO0_1/CLKOUT/CT32B0_MAT2/USB_FTOGGLE 4 GPIO_24-BL_EN
PIO0_2/SSEL/CT16B0_CAP0 10 GPIO_4
+3V3
PIO0_3/USB_VBUS 14 GPIO_25-VBUS
15 GPIO_27-SCL
6
PIO0_4/SCL
PIO0_5/SDA 16
22
GPIO_26-SDA
GPIO_19-USB_CONN
LED
XTALIN PIO0_6/USB_CONNECT/SCK
Y1 7 XTALOUT PIO0_7/CTS 23 GPIO_7
12MHz PIO0_8/MISO/CT16B0_MAT0 27 GPIO_2-MISO
R44
R45
R46
R47
R48
10K
10K
10K
10K
28
0R
PIO0_9/MOSI/CT16B0_MAT1/SWO GPIO_1-MOSI
29 GPIO_20 J8
SWCLK/PIO0_10/SCK/CT16B0_MAT2
R49
C2 C3 32 GPIO_11 1 2
2K
TDI/PIO0_11/AD0/CT32B0_MAT3
18pF 18pF JTAG_TRST 3 4
TMS/PIO1_0/AD1/CT32B1_CAP0 33 GPIO_12 JTAG_TDI 5 6
34 GPIO_13 JTAG_TMS_SWDIO 7 8
LED2
TDO/PIO1_1/AD2/CT32B1_MAT0
RED
GND GND TRST/PIO1_2/AD3/CT32B1_MAT1 35 GPIO_14 JTAG_TCLK_SWCLK 9 10
SWDIO/PIO1_3/AD4/CT32B1_MAT2 39 GPIO_15 11 12
PIO1_4/AD5/CT32B1_MAT3/WAKEUP 40 GPIO_16-WAKEUP JTAG_TDO_SWO 13 14
R50 19 45 15 16
USB_DM PIO1_5/RTS/CT32B0_CAP0 GPIO_17 JTAG_RESET
USB_DM 33R PIO1_6/RXD/CT32B0_MAT0 46 GPIO_6-RXD GND 17 18
USB_DP PIO1_7/TXD/CT32B0_MAT1 47 GPIO_5-TXD 19 20
R51 20 9
USB_DP PIO1_8/CT16B1_CAP0 GPIO_18
33R PIO1_9/CT16B1_MAT0 17 GPIO_28
30 R52
PIO1_10/AD6/CT16B1_MAT1 GPIO_29 GPIO_14 JTAG_TRST
R53
R54
R55
R56
10K
10K
10K
10K
PIO1_11/AD7 42 GPIO_30 50
+3V3
45 ohm impedance routing, 90 ohm differential R57
No tracks within 10 times trace width 8 VDDIO PIO2_0/DTR 2 GPIO_8 GPIO_11 JTAG_TDI
No via's and no sharp angles PIO2_1/DSR 13 GPIO_9 50
C4 C5 PIO2_2/DCD 26 GPIO_10 R58
PIO2_3/RI 38 GPIO_31 GPIO_20 JTAG_TCLK_SWCLK GND
100nF 10nF PIO2_4 18 GPIO_32 50
PIO2_5 21 GPIO_33
1 R59
GND GND PIO2_6 GPIO_34 GPIO_0-RESET JTAG_RESET
+3V3
11 GPIO_35 J10
44
PIO2_7
12
50 FTSH-105-01-F-D-K
VDDCORE PIO2_8 GPIO_36 Default for J9
PIO2_9 24 GPIO_37 JTAG_TMS_SWDIO 2 1
C6 C7 PIO2_10 25 GPIO_38 JTAG_TCLK_SWCLK 4 3
PIO2_11/SCK 31 GPIO_3-SCK GPIO_12 1 SEL-LINK J9 JTAG_TDO_SWO 6 5
100nF 10nF 2 R60 8 7
JTAG_TMS_SWDIO JTAG_TDI
PIO3_0 36 GPIO_21 GPIO_15 3 50 JTAG_RESET 10 9
GND GND PIO3_1 37 GPIO_22
5 VSSIO PIO3_2 43 GPIO_23
41 VSS PIO3_3 48 GPIO_39 GPIO_1-MOSI 1 SEL-LINK J11 R61 GND
2 JTAG_TDO_SWO
GPIO_13 3 50
GND
Default for J11
Default: not inserted
mbed/LPC17xx module interfaces (Ethernet and CAN), common USB interface and RS422/485 interface
J61 R217
6 5 15K Default for J12, J13
4 3 R203
2 1 R216
VIN 5K
2X03
15K R62
VBUS_SENSE 1 SEL-LINK J12
2
GND
GPIO_25-VBUS
CAN transceiver
GND 1K 3
L1
VBUS-1
BL_EN 1 SEL-LINK J13
CAN interface
MI0805K400R-10 2 GPIO_24-BL_EN
C8 3 CAN-H 8 J15-8 CAN-H
U4
100nF TJA1040 R63 7 CAN-L
USB VCC 1 TD 1 TXD CANH 7 60R
J15-7
LINE1
LINE2
3 RD 4 5 6 GND
Host USB+
USB- 2
GND
R64 270R 8
RXD SPLIT
CANL 6 C9
J15-6
+3V3
STB R65
4
Interface GND
GND Default for J14
VIN 3
2
VCC 60R 1nF GND
J60G$3 GND C10 C11 GND
+
J60G$2 GND
J60G$4
GND U5
R66
R67
24K
10K
GND 22uF/10V 100nF GND CAN-L PESD1CAN
J60G$5 1
Q1 R68 J14 SEL-LINK GPIO_19-USB_CONN
BC857B 2 GND GND GND
3K 3 GND
GND
R69
1K5
USB 1
2 USB_DM
USB_DP
Device 3
4
LINE1
LINE2
VCC
Interface 5
45 ohm impedance routing, 90 ohm differential
No tracks within 10 times trace width
GND
No via's and no sharp angles
C12 D3
RS422/RS485 transceiver
R70
1M
PRTR5V0U2X VIN
10n/500V
C13 C14
+
GND
22uF/10V 100nF
GND RS422for RS485.or RS485
R71
Insert jumpers
1K
GND GND
RXD
TXD Default for J16
RJ45 Ethernet Connector
+3V3
Default for J17 U6 J16
R72
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo