Service Manuals, User Guides, Schematic Diagrams or docs for : KONKA LCD KL37CS31 Konka_26CS66_KL32CS66_KL37CS66_42CS66_KL32CS31_KL37CS31_KL42CS31_LCD_TV_Service_Manual

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.



Image preview - the first page of the document



>> Download Konka_26CS66_KL32CS66_KL37CS66_42CS66_KL32CS31_KL37CS31_KL42CS31_LCD_TV_Service_Manual documenatation <<

Text preview - extract from the document

LCD    TV SERVICE                 MANUAL



              Modle list

KL26CS66,KL32CS66,KL37CS66
KL42CS66,KL32CS31,KL37CS31
        KL42CS31




      KONKA GROUP CO,LTD.
        Digital Flat Display Division
                     IMPORTANT SERVICE SAFETY INFORMATION
       Operating the receiver outside of its cabinet or with its back removed involves a shock hazard. Work on these
models should only be performed by those who are thoroughly familiar with precautions necessary when working on
high voltage equipment.
       Exercise care when servicing this chassis with power applied. if carelessly contacted, can cause serious shock or
result in damage to the chassis. Maintain interconnecting ground lead connections between chassis, escutcheon, picture
tube dag and tuner when operating chassis.
       When it is necessary to make measurements or tests with AC power applied to the receiver chassis, an Isolation
Transformer must be used as a safety precaution and to prevent possible damage to transistors. The Isolation
Transformer should be connected between the TV line cord plug and the AC power outlet.
       It is important to maintain specified values of all components and anywhere else in the received that could cause
a rise in operating supply voltages. No changes should be made to the original design of the receiver.
       Components shown in the shaded areas on the schematic diagram and/or identified by in the replacement parts
list should be replaced only with exact factory recommended replacement parts. The use of unauthorized substitute
parts man creates may create shock, fire, or other hazards.
       Before returning the receiver to the user, perform the following safety checks:
1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis
   and other metal parts in the receiver.
2. Replace all protective devices such as non-metallic control knobs, insulating fish papers, cabinet backs, adjustment
   and compartment covers of shields, isolation resistor-capacitor networks, mechanical insulators etc.
3. To be sure that not shock hazard exists, a check for the presence of leakage current should be made at each exposed
   metal part having a return path to the chassis (antenna, cabinet metal, screw heads knobs and/or shafts, escutcheon,
   etc.) in the following manner.
       Plug the AC line cord directly into a 110V/220V/240V, AC receptacle. (Do not use an Isolation Transformer
during these checks.) All checks must be repeated with the AC line cord plug connection reversed. (If necessary, a
non-polarized adapter plug must be used only for the purpose of completing these checks.)



PLEASE READ BEFORE ATTEMPTING SERVICE
1. Use an Isolation Transformer when performing any service on this chassis.
2. Never disconnect any leads while receiver is in operation.
3. Disconnect all power before attempting any repairs.
4. Do not short any position of the circuit while the power is on.
5. For safety reasons, replace components any with identical replacement parts (SEE PARTS LIST).
6. Before alignment, warm up the TV for at least 30 minutes.
7. When removing a PCB or related component, after unfastening or changing a wire, be sure to put the
   wire back in its original position.
8. Inferior silicon grease can damage IC's and transistors. When replacing IC's and transistors, use only
   specified silicon grease. Remove all old silicon when applying new silicon.
9. Before removing the anode cap, discharge eletricity because it contains high voltage.
                                          A. SPECIFICATION

System :       PAL:I , B/G , D/K;     SECAM: D/K , B/G

Audio Output Power :
     Size            26                    32             37                40                42
  Power(W)         4W*2                  5 W*2           5W*2             5 W*2             5 W*2

Antenna Impedance            :   75

Power Consumption : 340WMax
     Size           26      32                              37               42
    Power
                   160     180                             200               270
Consumption(W)

Power Supply             :       ~110240V,   50/60Hz


     Item    Port List
      1      RF    Cable
      2      Headphone Audio Output
      3      S-Video Input
      4      AV Input
      5      AV Output
      6      YPbPr
      7      Component Audio Input
      9      VGA/RGB
     10      VGA Audio Input
     11      HDMI Input




                                       B. ADJUSTMENT MANUAL
 TEST NOTE
1. Please follow the pointed test steps and choose the right test equipment to conduct adjustment,
     otherwise good effect of Unit could not be obtained. The unit should be warmed up for 30 minutes
     before adjustment and every parameter should be adjusted repeatedly till the optimum value
     obtained, the pointed voltage value should be ensured during test to get satisfied test result.

2.    Test environment
     1) Temperature       : 15

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo