Service Manuals, User Guides, Schematic Diagrams or docs for : Keithley 70xx 7011Cpinout

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download 7011Cpinout documenatation <<

Text preview - extract from the document

The following pages are extracts from the manual for the 7011-S and 7011-C switch
cards. The complete manual is available by download from the document center.
3.3.4 Multi-pin (mass termination) connec- connector card to test instrumentation and DUT (de-
tor card vices under test). In general, these accessories, which
are summarized in Table 3-2, utilize a round cable as-
sembly for connections.
Since comections to external circuiq are made at the
96-pin male DIN bulkhead connector, there is no need
to separate the connector card from the relay card. If Table 3-2
the connector card is separated from the relay card, Mass termination accessories
carefully mate them together and install tlw supplied
440 mounting screw. Make sure to handle the cards by Model Description
the edges and shields to avoid contamination.
7011-m-R 96pin female DIN connector and
housing for round cable.
Terminal identification for the DIN connedor of the 7011~ME-2 Two-meter round cable assembly
multi-pin connector card is provided by Figure 3-8. terminated with a 96-pin female
This connector will mate to a 96-pin female DIN con- DIN comwctor on each end.
nector.
7011~MTR 96-pin male DIN bulkhead con-

Keithley has a variety of cable and connector accesso-
ries available to accommodate connections from the
1 nector.

3-6
Card Connections & hstahtion

Pins of the Model 7011-C mass termination connector can be identiiied in one of three ways:
1. Mux terminal, consisting of banks A-D and inputs l-10.
2. Connector description. consisting of rows a-c and columns l-32.
3. Schematic and component layout designation (l-96).
The following pinout diagrams show the correspondence between these arrangements:

3231302928273~*25*423~221*0191~1716151413121110 9 8 7 6 5 4 3 2 1
l . . . . . . ..*.....*....*...........
View from pin side
of connector

3-7
Card Connections & /nm//arion

Typical connection techniques Round cable assemblies -Figure 3-9 shows typical
round cable connection techniques using accessories
All external circuitry, such as instrumentation and available from Keithley.
DLJTs,that you wish to connect to the multiplexer card
must be terminated with a single 9&pin female DIN
coMecror. The following coxlnection techniques pro- In Figure 3-9A, connections are accomplished using a
vide some guidelines and suggestions for wiring your Model 7011 h4TC-2 cable and a Model 7011~MTR bulk-
circui&y. head connector. The two-meter round cable is termi-
nated with a 96-pin female DIN connector at each end.
This cable mates directly to the multi-pin connector
WARNING card and to the bulkhead connector. The bulkhead con-
nector has solder cups to allow direct connection ia in-
Before beginning any wiring proce- strumentation and DUT. Figure 3-10 provider rhe
dures, make sure all power is off and
pinout for the bulkhead connector.
any stored energy in external circuit-
ry is discharged.
In Figure 3-9B, connections are accomplished using a
Model 7011 MTC-2 cable assembly that is cut in half.
NOTE
The 96-pin female DIN connector on one end of the ca-
External circuitry should be connected ble mates directly to the multi-pin connector card. The
(I ,7ed id only wirh the 7001's pow- unterminated end of the cable is wired directly to in-
e1 after the Model 7011 assembly is strumentation and DUT. The other half of the cable as-
in:;slled in the Model 7001 main- sembly could be used for a second switching card.
frame. Installation is covered in para-
graph 3.5.
In Figure 3-9C, connections are accomplished using a
custom-built cable assembly that consists of a Model
Output relays- The multi-pin connector card uses a 7011~KlT-R connector and a suitable round cable. Hita-
relay for each of the four output banks. These output chi cable part number N28!?`-P/D-50TAB is a 5O-con-
relays are normally open to prevent any hazardous ductor cable. Two of these cz~les can be used to supply
voltages (via the mainframe backplane) from appear- 100 conductors.The connector has solder cups to ac-
ing cm the pins of the rw.le DIN connector. The output commodate the individual wires of the unterminated
relays will only close when the Model 7011~MTC-2 ca- cable. Figure 3-11 provides an exploded view of the
ble assembly is connected to card. If building you own connector assembly and shows how the cable is con-
cable assembly, you must make sure that it shorts pins nected. The connector end of the resultant cable assem-
la to lb of the card ccmnector (Figure 3-8) when it is bly mates directly to the multi-pin connector card. The
mated to the card. Shorting pins la to lb allows the unterminated end of the cable assembly is wired di-
output relays to close. rl?crly to inshumen tation and DIJT.

3-8
Figure 3-9
Typical round cable connection techniques

3-9
View from solder
0 cup side of
connector

Note : See Figure 3-6 for terminal
identification.

Figure 3- 10
Model 7011 -MTR connector pinout

Figure 3- 11
Model 707 I-KIT-R (with/cable) assembly

3-10

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo