Service Manuals, User Guides, Schematic Diagrams or docs for : panasonic LCD TX-55CX700 firmware MQM0129DG010915REV2_Auto_Setup_Problem
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download MQM0129DG010915REV2_Auto_Setup_Problem documenatation <<
Text preview - extract from the document
Confidential
For Authorised Service Agents Only Ref No: MQM0129DG010915REV2
TECHNICAL INFORMATION
A P BG P CY P E P FL P I P LT P MD P NL P S P TR P Date
AL P BIH P CZ P EST P GB P IRL P LV P MK P P P SK P UA P 03.09.2015
AND P BY P D P F P GR P IS P M P MNE P PL P SLO P Country Reported
B P CH P DK P FIN P H P L P MC P N P RO P SRB P Europe
Product Category: LCD TV / LCD IDTV
Subject: The On-Screen Display disappears the first time the TV is set up
Model(s) Affected: Please see below
Symptom / Cause: The On-Screen Display disappears the first time the TV is set up.
Remedy / Method: This applies to all units prior to serial number: N*-5420001
Upgrade the set software to version 3.208
Preparation
Prepare a USB memory device with a capacity around 2Gb to 4Gb
Obtain a copy of the compressed software from your ususal service source
Upgrade Procedure
1. Uncompress the software and copy to the root directory of the USB memory device
2. With the set disconnected from mains power, insert the USB memory device into USB1 socket on the TV
3. Whilst pressing and holding the volume down/minus ("-") button, connect mains power
- The red LED will illuminate steadily
- After a short while, the red LED will then start to blink slowly
4. When the red LED starts blinking slowly, release the volume down/minus ("-") button
- The red LED will continue to blink slowly whilst the set software is upgrading
5. When the red LED stops blinking, remove the USB memory device
6. Disconnect the mains power, then re-connect mains power
- For a short while nothing will appear to happen
- Then the red LED will blink once, then the green LED will start blinking
7. Once the set starts the auto setup process, self check the set to confirm the software version
Models Affected:
TX-55/65CR730B TX-43/49/55/60CX740E TX-49/55CXN758
TX-55/65CR852B TX-43/49/55/60CX750E TX-40/50/55CXR680
TX-40/50/55CX680B TX-40/50/55/65CX800E TX-40/50/55CXR700
TX-40/50/55/65CX700B TX-55/65CRW734 TX-50CXR705
TX-40/50/55/65CX802B TX-55/65CRW854 TX-40/50/55/65CXR800
TX-55/65CR730E TX-40/50/55/65CXC725 TX-49/55CXT756
TX-55/65CR850E TX-40/50/55CXE720 TX-40/50/55CXW674
TX-40/50/55CX670E TX-49/55CXF757 TX-40/50/55CXW684
TX-40/50/55CX680E TX-40/50/55CXM710 TX-40/50/55/65CXW704
TX-40/50/55/65CX700E TX-40/50/55CXM715 TX-43/49/55/60CXW754
TX-40/50/55/65CXW804 TX-49/55CXX759 TX-55CXX759
Warranty Claims - Please use the following IRIS and Activity codes
Activity Codes: Guarantee Code Activity Location Stock Indicator
(UK Only) A U F D
Symptom Section Defect
Condition Repair
IRIS Codes: Area Type Code Area Code Area Code
C 1 1 11A 1 SYS 1 1 i
Note: Failure to use the correct IRIS and Activity codes may result in the claim being rejected
Document No: MQM_TI
Panasonic 1 of 1 Rev: 12.00 DG110612
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo