Service Manuals, User Guides, Schematic Diagrams or docs for : teac TV CTM6828V2

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.



Image preview - the first page of the document



>> Download CTM6828V2 documenatation <<

Text preview - extract from the document

                      SERVICE MANUAL


                        Version 2- 68 cm CTV




Effective: MAY 2000                CTM6828V2SERV
                                         TECHNICAL BULLETIN                                            26-Jun-00


MODEL:               CT-M5930S, CT-M6828S, CT-F683
PROBLEM:             RF Interference

File: CTM5830 6828 683 rf interf tb.doc


Some units of the first production lot for the models of reference have been supplied with a low quality RF lead
from the RF connector in the back panel to the tuner input. Those units may display diagonal interference lines
on the picture mainly in VHF bands.




Note that the braid of the good quality cable is very tight and totally covers the internal wire.



Instructions

    Replaced the faulty RF cable assembly using the part number 40252200111.




Regards,


Alcides Berta
TEAC Australia Pty Ltd.




                                                 Page 1 of 1
                                    TECHNICAL BULLETIN                                        12-July-2000


MODEL:             CT-F683, CT-M6828S, CT-M5930
PROBLEM:           I2C Mitsubishi chassis. Service Mode adjustments

File: CT-F683 CT-M6828 5930 RC tb.doc

The following information applies to all Great Wall models using I2C Mitsubishi technology. A
special type of remote control is necessary to access Service Mode adjustments, please refer to
the figure.


Accessing Service Mode

    1- Press first button on the left of the FACTORY ON row (Button 1). The
       word Key is visible on the screen.
    2- Press FACTORY button (Button 2). The first page of factory
       adjustments will be displayed.
    3- Navigate between parameters and different pages using UP and DOWN
       buttons. Direct access to frequently used parameters is available from
       dedicated buttons, for example EW WIDTH, V AMPL, etc.
    4- Adjust parameter values using VALUE+ and VALUE -.



Leaving Service Mode


    1- Press first button on the left of the FACTORY ON row (Button 1). The
       work Key is visible on the screen.
    2- Press STANDBY button.
    3- Turn POWER off from the front panel switch for at least 15 seconds.


Note:

The final version of remote control may be slightly different from the one used
to prepare this bulletin.


Regards,

Alcides Berta
TEAC Australia Pty Ltd.




                                             Page 1 of 1
                                  TECHNICAL BULLETIN                                      21-Jul-2000


MODEL:             CT-M6828S CT-F683 CT-M5930S
PROBLEM:           Audio noise


File: CT M6828S M5930S F683 noise tb.doc

A humming noise is audible at low volume from the speakers and particularly from the headphone
output (when available). The source of this noise is the vertical deflection circuit.


Instructions

    1- Delete the jumper W286 on the main PCB next to CN111 in the fly-back transformer area.
    2- Add a cable between the IF shielding can and the heat sink for the audio output IC.




Regards,


Alcides Berta
TEAC Australia Pty Ltd.




                                           Page 1 of 1
                                        TECHNICAL BULLETIN                                    11-August-2000


MODEL:             CT-M6828S, CT-M5930 and CT-F683
PROBLEM:           Incorrect resistor type

File: CT-M6828S m oxide.doc

An incorrect resistor type has been fitted in position R504 of the neck board in some units. A
carbon film resistor having a light brown color body and mounted on the surface of the PCB can
eventually ignite and burn the board.




Instructions


Replace the carbon film resistor in location R504 with a metal oxide type. Separate the new
resistor from the surface of the PCB by approximately 10 mm.




                    Wrong type                                            Correct type
                 Carbon film resistor                                   Metal oxide resistor
                 PN: 11347020512                                        PN: 11347020575
                   47 Ohm, 

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo