Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Infiniti G35 2003-2005 Coupe Sedan Approved Infiniti G35 Sedan 2004 First Edition ex
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download ex documenatation <<
Text preview - extract from the document
EXHAUST SYSTEM
B ENGINE
A
EX
SECTION
EXHAUST SYSTEM C
D
E
CONTENTS
PREPARATION .......................................................... 2
. Checking Exhaust System ....................................... 3. F
Commercial Service Tools ....................................... 2
. Removal and Installation ......................................... 3
.
EXHAUST SYSTEM .................................................. 3
. REMOVAL ............................................................ 4
.
INSTALLATION .................................................... 4
. G
INSPECTION AFTER INSTALLATION ................. 4 .
SERVICE DATA AND SPECIFICATIONS (SDS) ....... 5 .
Tightening Torque .................................................... 5
.
H
I
J
K
L
M
EX-1
PREPARATION
PREPARATION PFP:00002
Commercial Service Tools ABS00021
Tool name Description
Power tool Loosening nuts and bolts
PBIC0190E
EX-2
EXHAUST SYSTEM
EXHAUST SYSTEM PFP:20100
A
Checking Exhaust System ABS0002X
Check exhaust pipes, muffler and mounting for improper attachment,
leaks, cracks, damage or deterioration. EX
q If anything is found, repair or replace damaged parts.
C
D
SMA211A
E
Removal and Installation ABS0002Y
CAUTION:
q Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat F
resistance, corrosion resistance, and shape.
q Perform the operation with the exhaust system fully cooled down because the system will be hot
just after the engine stops.
G
q Be careful not to cut your hand on the heated insulator edge.
H
I
J
K
L
M
PBIC2668E
1. Finisher 2. Mounting bracket 3. Mounting rubber
4. Main muffler 5. Collar 6. Mounting rubber
7. Ring gasket 8. Ground cable 9. Center muffler
10. Mounting bracket 11. Collar 12. Grommet
EX-3
EXHAUST SYSTEM
13. Exhaust mounting bracket 14. Grommet 15. Gasket
16. Exhaust front tube
REMOVAL
Disconnect each joint and mounting using power tool.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
q Always replace exhaust gaskets with new ones when reassembling.
q If heated insulator is badly deformed, repair or replace it. If deposits such as mud pile up on the
insulator, remove them.
q When installing heated insulator avoid large gaps or interference between heated insulator and
each exhaust pipe.
q Remove deposits from the sealing surface of each connection. Connect them securely to avoid
gases leakage.
q Temporarily tighten mounting nuts. Check each part for unusual interference, and then tighten
them to the specified torque.
q When installing each mounting rubber, avoid twisting or unusual extension in up/down and right/
left directions.
INSPECTION AFTER INSTALLATION
q With the engine running, check exhaust tube joints for gas leakage and unusual noises.
q Check to ensure that mounting brackets and mounting rubbers are installed properly and free from undue
stress. Improper installation could result in excessive noise and vibration.
q Make sure that clearance between finisher and rear bumper is even.
EX-4
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS) PFP:00030
A
Tightening Torque ABS00032
Unit: N◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo