Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Infiniti QX56 JA60 2004-2005 Approved 2004_QX56 sb
<< Back |
HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download
Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing.
If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download sb documenatation <<Text preview - extract from the documentH RESTRAINTS
A
SECTION SB
SEAT BELTS
B
C
D
E
CONTENTS
PRECAUTIONS ......................................................... 2
. INSTALLATION OF SEAT BELT RETRACTOR - F
Precautions for Supplemental Restraint System BENCH SEAT ....................................................... 7
.
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Third Row ................................................................ 8
.
SIONER" ................................................................. 2
. REMOVAL AND INSTALLATION ......................... 8 . G
Precautions for Seat Belt Service ........................... 2 . Third Row Center .................................................... 9
.
AFTER A COLLISION .......................................... 2 . REMOVAL AND INSTALLATION ......................... 9 .
SEAT BELTS ............................................................. 3
. Seat Belt Inspection ............................................... 10
.
SB
Removal and Installation of Front Seat Belt ............ 3 . AFTER A COLLISION ........................................ 10 .
REMOVAL OF SEAT BELT RETRACTOR ........... 4 . PRELIMINARY CHECKS ................................... 10 .
INSTALLATION OF SEAT BELT RETRACTOR..... 4 SEAT BELT RETRACTOR ON-VEHICLE
REMOVAL OF SEAT BELT BUCKLE ................... 5 . CHECK ............................................................... 11
. I
INSTALLATION OF SEAT BELT BUCKLE ........... 5 . SEAT BELT RETRACTOR OFF-VEHICLE
Removal and Installation of Rear Seat Belt ............ 6 . CHECK ............................................................... 11
.
REMOVAL ............................................................ 6
. LATCH (LOWER ANCHORS AND TETHER FOR J
INSTALLATION .................................................... 7
. CHILDREN) SYSTEM .............................................. 13 .
REMOVAL OF SEAT BELT BUCKLE ................... 7 . Removal and Installation ....................................... 13 .
INSTALLATION OF SEAT BELT BUCKLE ........... 7 . TOP TETHER STRAP CHILD RESTRAINT ............ 14 .
K
REMOVAL OF SEAT BELT RETRACTOR - Removal and Installation ....................................... 14 .
BENCH SEAT ...................................................... 7
.
L
M
Revision: August 2007 SB-1 2004 QX56
PRECAUTIONS
PRECAUTIONS PFP:00001
Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EHS000VP
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
G To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
G Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
G Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Seat Belt Service EHS000VQ
CAUTION:
G Before removing the seat belt pre-tensioner assembly, turn the ignition switch OFF, disconnect
both battery cables and wait at least 3 minutes.
G After replacing or reinstalling seat belt pre-tensioner assembly, or reconnecting seat belt pre-ten-
sioner assembly connector, ensure entire SRS operates properly. Refer to SRS-20, "SRS Opera-
tion Check" .
G Do not disassemble buckle or seat belt assembly.
G Do not reuse seat belt anchor bolts after removal. Replace with new ones.
G Replace anchor bolts if they are deformed or worn out.
G Never oil tongue and buckle.
G If any component of seat belt assembly is questionable, do not repair. Replace the whole seat belt
assembly.
G If webbing is cut, frayed, or damaged, replace seat belt assembly.
G When replacing seat belt assembly, use a genuine NISSAN seat belt assembly.
AFTER A COLLISION
WARNING:
G Inspect all seat belt assemblies including retractors and attaching hardware after any collision.
G NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the
collision was minor and the belts show no damage and continue to operate properly. Failure to do
so could result in serious personal injury in an accident. Seat belt assemblies not in use during a
collision should also be replaced if either damage or improper operation is noted. Seat belt pre-
tensioner should be replaced even if the seat belts are not in use during a frontal collision in which
the air bags are deployed.
Replace any seat belt assembly (including anchor bolts) if:
G The seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and
buckles show no damage and continue to operate properly).
G The seat belt was damaged in an accident. (i.e., torn webbing, bent retractor or guide, etc.)
G The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage
or distortion and repair as necessary before installing a new seat belt assembly.
G Anchor bolts are deformed or worn out.
G The seat belt pre-tensioner should be replaced even if the seat belts are not in use during the collision in
which the air bags are deployed.
Revision: August 2007 SB-2 2004 QX56
SEAT BELTS
SEAT BELTS PFP:86884
A
Removal and Installation of Front Seat Belt EHS000VR
B
C
D
E
F
G
SB
I
J
K
L
M
WHIA0236E
1. Assist handle 2. Assist handle screw cover 3. D-ring anchor bolt cover
4. Seat belt buckle 5. Seat belt retractor and belt assem- 6. Anchor cover
bly LH
7. Seat belt pre-tensioner connector 8. Center pillar lower finisher 9. Seat belt anchor
10. Center pillar 11. Center pillar upper finisher 12. Seat belt height adjuster
13. Seat belt height adjuster finisher
Revision: August 2007 SB-3 2004 QX56
SEAT BELTS
REMOVAL OF SEAT BELT RETRACTOR
CAUTION:
G Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
1. Remove the center pillar upper/lower finishers. Refer to EI-34, "BODY SIDE TRIM" .
2. Remove the seat belt retractor anchor bolts and seat belt retractor and belt assembly.
G On RH side, disconnect the seat belt tension sensor.
WHIA0237E
3. Disconnect the seat belt pre-tensioner electrical connector.
CAUTION:
G For installing/removing seat belt pre-tensioner connector,
insert a thin screwdriver wrapped in tape into the notch, lift
the lock and remove the connector.
G Install the connector with the lock raised, and push the lock
into the connector.
PHIA0341E
INSTALLATION OF SEAT BELT RETRACTOR
Installation is in the reverse order of removal.
G Install the seat belt retractor and belt assembly upper bolt first.
G Ensure that seat belt height adjuster is locked in the lowest position during installation.
Revision: August 2007 SB-4 2004 QX56
SEAT BELTS
REMOVAL OF SEAT BELT BUCKLE
1. Remove the front seat. Refer to SE-96, "Components" . A
2. Remove the seat cushion. Refer to SE-101, "SEAT CUSHION TRIM AND PAD" .
3. Remove screw and seat cushion inner finisher.
B
4. Remove the anchor bolt and buckle.
C
D
E
WHIA0238E
INSTALLATION OF SEAT BELT BUCKLE
Installation is in the reverse order of removal. F
G
SB
I
J
K
L
M
Revision: August 2007 SB-5 2004 QX56
SEAT BELTS
Removal and Installation of Rear Seat Belt EHS000VS
Second Row
WHIA0239E
1. Seat belt height adjuster 2. D-ring anchor bolt cover 3. D-ring anchor
4. Seat belt retractor and belt assem- 5. Seat belt buckle 6. Seat belt retractor cover
bly
7. Push pin 8. Seat belt retractor and belt assem- 9. Seat belt bezel
bly
10. Seat belt buckle 11. Seat cushion finisher 12. Seat belt lower anchor
REMOVAL
1. Remove seat belt lower anchor cover and bolt.
2. Remove the D-ring anchor bolt cover and D-ring anchor bolt.
3. Remove the luggage side finisher and luggage side finisher lower. Refer to EI-39, "LUGGAGE FLOOR
TRIM" .
Revision: August 2007 SB-6 2004 QX56
SEAT BELTS
4. Remove the seat belt guide bolt.
5. Remove seat belt retractor anchor bolt and the seat belt retractor and belt assembly. A
6. Remove the seat belt height adjustor assembly.
INSTALLATION B
Installation is in the reverse order of removal.
G Ensure that seat belt height adjuster is locked in the lowest position during installation.
C
REMOVAL OF SEAT BELT BUCKLE
1. Remove the rear bucket seat. Refer to SE-103, "Removal and
Installation" . D
2. Remove the screw and seat cushion finisher. Refer to SE-103,
"Removal and Installation" .
3. Remove the anchor bolt and buckle. E
F
WHIA0229E
G
4. Remove the rear bench seat. Refer to SE-103, "Removal and Installation" .
5. Remove the seat cushion finisher.
6. Remove the anchor bolt and buckle. SB
INSTALLATION OF SEAT BELT BUCKLE
Installation is in the reverse order of removal. I
REMOVAL OF SEAT BELT RETRACTOR - BENCH SEAT
1. Remove seat belt anchor.
2. Remove seat belt bezel. J
3. Remove seat back upholstery and foam. Refer to SE-103, "Removal and Installation" .
4. Remove seat belt retractor cover.
K
5. Remove bolt and remove seat belt retractor and belt assembly.
INSTALLATION OF SEAT BELT RETRACTOR - BENCH SEAT
Installation is in the reverse order of removal. L
M
Revision: August 2007 SB-7 2004 QX56
SEAT BELTS
Third Row EHS000VT
REMOVAL AND INSTALLATION
Third Row Outboard
WHIA0240E
1. D-ring mounting bracket 2. Seat belt retractor and belt assem- 3. Retractor mounting bracket
bly
4. Seat belt lower anchor 5. Lower anchor bolt cover 6. Seat belt buckles
7. Seat belt buckle anchor bolt 8. D-ring anchor bolt cover 9. D-ring anchor
REMOVAL
1. Remove the D-ring anchor bolt cover and D-ring anchor bolt.
2. Remove the lower anchor bolt cover and lower anchor bolt.
3. Remove the luggage side finisher and luggage side finisher lower. Refer to EI-39, "LUGGAGE FLOOR
TRIM" .
4. Remove the seat belt retractor anchor bolt, LH side, and seat belt retractor and belt assembly.
Revision: August 2007 SB-8 2004 QX56
SEAT BELTS
5. Remove the seat belt retractor anchor nut, RH side, and seat belt retractor and belt assembly.
6. Remove seat belt buckle anchor bolt from seat belt anchor base and remove seat belt buckles. A
INSTALLATION
Installation is in the reverse order of removal. B
G Ensure that seat belt height adjuster is locked in the lowest position during installation.
G Seat belt anchor base should be flat to the floor during installation and not on the anti-rotation bead.
Third Row Center EHS000VU
C
REMOVAL AND INSTALLATION
D
E
F
G
SB
I
J
K
WHIA0230E
L
REMOVAL
1. Remove the rear roof finisher. Refer to EI-37, "HEADLINING" .
2. Lower the rear portion of the headliner.
M
3. Remove the seat belt retractor anchor bolts and seat belt retractor and belt assembly.
INSTALLATION
Installation is in the reverse order of removal.
Revision: August 2007 SB-9 2004 QX56
SEAT BELTS
Seat Belt Inspection EHS000VV
AFTER A COLLISION
WARNING:
Inspect all seat belt assemblies including retractors and attaching hardware after any collision.
NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the col-
lision was minor and the belts show no damage and continue to operate properly. Failure to do so
could result in serious personal injury in an accident. Seat belt assemblies not in use during a colli-
sion should also be replaced if either damage or improper operation is noted. Seat belt pre-tensioners
should be replaced even if the seat belts are not in use during a frontal collision in which the air bags
are deployed.
Replace any seat belt retractor and belt assembly (including anchor bolts) if:
G The seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and
buckles show no damage and continue to operate properly).
G The seat belt was damaged in an accident. (i.e. torn webbing, bent retractor or guide).
G The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage
or distortion and repair as necessary before installing a new seat belt retractor and belt assembly.
G Anchor bolts are deformed or worn out.
G The seat belt pre-tensioner should be replaced even if the seat belts are not in use during the collision in
which the air bags are deployed.
PRELIMINARY CHECKS
1. Check the seat belt warning lamp/chime for proper operation as follows:
a. Switch ignition ON. The seat belt warning lamp should illuminate. Also, the seat belt warning chime should
sound for about seven seconds.
b. Fasten drivers seat belt. The seat belt warning lamp should go out and the chime (if sounding) should
stop.
2. If the air bag warning lamp is blinking, conduct self-diagnosis using CONSULT-II, and air bag warning
lamp. Refer to SRS-20, "SRS Operation Check" .
3. Check that the seat belt retractor and belt assembly, seat belt anchor and buckle bolts are securely
attached.
4. Check the shoulder seat belt guide and shoulder belt height adjuster for front seats. Ensure guide swivels
freely and that belt lays flat and does not bind in guide. Ensure height adjuster operates properly and
holds securely.
5. Check retractor operation:
a. Fully extend the seat belt webbing and check for twists, tears or other damage.
b. Allow the seat belt to retract. Ensure that belt returns smoothly and completely into the retractor. If the
seat belt does not return smoothly, wipe the inside of the loops with a clean paper cloth, because dirt built
up in the loops of the upper anchors can cause the seat belts to retract slowly.
c. Fasten the seat belt. Check the seat belt returns smoothly and completely to the retractor. If the belt does
not return smoothly, the cause may be an accumulation of dust or dirt. Use the "SEAT BELT TAPE SET"
and perform the following steps.
Inspect the front seat belt through-anchor:
1. Pull the seat belt out to a length of 500 mm (19.69 in) or more.
2. Use a clip or other device to hold the seat belt at the center pillar belt opening.
3. Pass a thin wire through the through-anchor belt opening. Hold both ends of the wire and pull taut while
moving it up and down several times along the belt opening surface to remove dirt.
4. Any dirt that cannot be removed with the wire can be removed by cleaning the opening with a clean
cloth.
5. Apply tape at the point where the belt contacts the through-anchor belt opening.
NOTE:
Apply the tape so that there is no looseness or wrinkling.
6. Remove the clip holding the seat belt and check that the belt returns smoothly.
7. Repeat steps above as necessary to check the other seat belts.
Revision: August 2007 SB-10 2004 QX56
SEAT BELTS
SEAT BELT RETRACTOR ON-VEHICLE CHECK
Emergency Locking Retractors (ELR) and Automatic Locking Retractors (ALR) A
NOTE:
All seat belt retractors are of the Emergency Locking Retractors (ELR) type. In an emergency (sudden stop)
the retractor will lock and prevent the belt from extending any further. All 3-point type seat belt retractors B
except the driver's seat belt also have an Automatic Locking Retractors (ALR) mode. The ALR mode (also
called child restraint mode) is used when installing child seats. The ALR mode is activated when the seat belt
is fully extended. When the belt is then retracted partially, the ALR mode automatically locks the seat belt in a C
specific position so the belt cannot be extended any further. To cancel the ALR mode, allow the seat belt to
fully wind back into the retractor.
Check the seat belt retractors using the following test(s) to determine if a seat belt retractor and belt assembly
is operating properly. D
ELR Function Stationary Check
Grasp the shoulder belt and pull forward quickly. The retractor should lock and prevent the belt from extending E
further.
ALR Function Stationary Check
1. Pull out entire length of seat belt from retractor until a click is heard. F
2. Retract the belt partially. A clicking noise should be heard as the belt retracts indicating that the retractor is
in the Automatic Locking Retractor (ALR) mode.
3. Grasp the seat belt and try to pull out the retractor. The belt must lock and not extend any further. If neces- G
sary replace the seat belt retractor and belt assembly.
4. Allow the entire length of the belt to retract to cancel the automatic locking mode.
SB
ELR Function Moving Check
WARNING:
Perform the following test in a safe, open area clear of other vehicles and obstructions (for example, a I
large, empty parking lot). Road surface must be paved and dry. DO NOT perform the following test on
wet or gravel roads or on public streets and highways. This could result in an accident and serious
personal injury. The driver and passenger must be prepared to brace themselves in the event the
J
retractor does not lock.
1. Fasten drivers seat belt. Buckle a passenger into the seat for the belt that is to be tested.
2. Proceed to the designated safe area. K
3. Drive the vehicle at approximately 16 km/h (10 MPH). Notify any passengers of a pending sudden stop.
The driver and passenger must be prepared to brace themselves in the event the retractor does not lock.
Apply brakes firmly and make a very hard stop.
L
During stop, seat belts should lock and not be extended. If the seat belt retractor and belt assembly does not
lock, perform the retractor off-vehicle check.
M
SEAT BELT RETRACTOR OFF-VEHICLE CHECK
1. Remove the seat belt retractor and belt assembly.
2. Slowly pull out belt while tilting the retractor assembly forward from the mounted position without twisting
the retractor assembly as shown in the illustration.
Revision: August 2007 SB-11 2004 QX56
SEAT BELTS
PHIA0257E
15 degrees or less tilt : Belt can be pulled out.
35 degrees or more tilt : Belt locks and cannot be pulled out.
If NG, replace the retractor assembly.
Revision: August 2007 SB-12 2004 QX56
LATCH (LOWER ANCHORS AND TETHER FOR CHILDREN) SYSTEM
LATCH (LOWER ANCHORS AND TETHER FOR CHILDREN) SYSTEM PFP:75466
A
Removal and Installation EHS000VW
NOTE:
The LATCH (Lower Anchors and Tether for Children) system is not serviceable. B
C
D
E
F
G
SB
I
J
K
L
M
Revision: August 2007 SB-13 2004 QX56
TOP TETHER STRAP CHILD RESTRAINT
TOP TETHER STRAP CHILD RESTRAINT PFP:88000
Removal and Installation EHS000VX
1. Remove luggage room rear lower finisher. Refer to EI-39, "LUG-
GAGE FLOOR TRIM" .
2. Remove bolt and remove tether anchor from the luggage box
bracket.
Installation is in the reverse order of removal.
WHIA0234E
Revision: August 2007 SB-14 2004 QX56
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo