Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Jeep Cherokee XJ 1988-1989.1993-1995 Approved 1995 XJ Jeep Cherokee 95XJ_8T
<< Back |
HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download
Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing.
If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download 95XJ_8T documenatation <<Text preview - extract from the documentJ POWER MIRRORS 8T - 1
POWER MIRRORS
CONTENTS
page page
DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SERVICE PROCEDURES ................... 4
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . 1
GENERAL INFORMATION
Power outside rear view mirrors are an available ponent of the mirror unit is faulty or damaged, the
option on XJ (Cherokee) models. Following are gen- entire assembly must be replaced.
eral descriptions of the major components in the
power mirror system. Refer to Group 8W - Wiring Di- POWER MIRROR SWITCH
agrams for complete circuit descriptions and dia- Both the right and left mirror are controlled by a
grams. multi-function switch located on the front of the cen-
ter console storage compartment, directly below the
POWER MIRROR armrest. The selector switch is moved right (right
The power mirrors are connected to battery feed at mirror control), left (left mirror control), or center to
all times. Each mirror head contains two electric mo- turn power mirrors off. Then one of four directional
tors, two drive mechanisms and the mirror glass. control buttons is depressed to control movement of
One motor and drive controls mirror up-and-down the selected mirror up, down, right, or left. The
movement, and the other controls right-and-left
power mirror switch is serviced only as a complete
movement.
unit.
The mirror glass is the only serviced replacement
part for the power mirror assembly. If any other com-
DIAGNOSIS
POWER MIRROR SYSTEM (7) See Power Mirror Switch illustration. Connect
(1) Check fuse 16 in Power Distribution Center a jumper wire from mirror switch connector cavity
(PDC) and fuse 9 in fuseblock module. If OK, go to for pin E to cavity for pin F. Now connect a second
next step. If not OK, replace fuse. jumper from connector cavity for pin G to each of the
(2) Check for battery voltage at fuse 9 in fuseblock following pin cavities: A, B, C, then D. In each case,
module. If OK, go to next step. If not OK, repair cir- the selected mirror head should move. If OK, replace
cuit to fuse 16 in PDC. switch. If not OK, go to next step.
(3) Remove power mirror switch from the center (8) Remove door trim panel and unplug power mir-
console. See Power Mirror Switch Remove/Install. ror connector inside door. Connect one jumper wire to
(4) Disconnect wiring harness connector from a good ground and a second jumper wire to a battery
switch. Check for battery voltage at pink wire. If OK, feed. Connect other ends of jumpers to the mirror
go to next step. If not OK, repair circuit to fuse 9 in side of connector in door (refer to Group 8W - Wiring
fuseblock module. Diagrams for connector cavity identification). Mirror
(5) Check for continuity between black wire in head should move in each of the four directions. If
switch harness connector and a good ground. There
OK, repair wiring between mirror switch and door
should be continuity. If OK, go to next step. If not
connectors. If not OK, replace mirror.
OK, repair circuit to ground.
(6) Check switch continuity as shown in the Mirror
Switch Continuity charts. If OK, go to next step. If
not OK, replace switch.
8T - 2 POWER MIRRORS J
POWER MIRROR SWITCH
J POWER MIRRORS 8T - 3
POWER MIRROR SWITCH CONTINUITY (LEFT POSITION)
POWER MIRROR SWITCH CONTINUITY (RIGHT POSITION)
8T - 4 POWER MIRRORS J
SERVICE PROCEDURES
POWER MIRROR SWITCH REMOVE/INSTALL (2) Disconnect control linkage and wire harness
(1) Disconnect battery negative cable. connector.
(2) Using a wide flat-bladed tool, pry the switch (3) Remove latch release and control panel assem-
housing away from the center console (Fig. 1). bly.
(4) Remove armrest lower retaining screws.
(5) Swing armrest downward to a vertical position.
This is necessary to disconnect the armrest from the
upper retainer clip (Fig. 3).
Fig. 1 Power Mirror Switch Remove/Install
(3) Disconnect switch connector and remove
switch.
(4) Reverse removal procedures to install.
POWER MIRROR REMOVE/INSTALL
(1) Remove interior door latch release assembly
and control panel retaining screws (Fig. 2).
Fig. 3 Armrest Retainer Clip
(6) Pull the armrest straight out from the trim
panel.
(7) Remove the trim panel with a wide flat-bladed
tool (Fig. 4). To aid in removal of the trim panel,
start at the bottom of the panel.
Fig. 2 Door Control Panel Remove/Install
Fig. 4 Trim Panel Remove
J POWER MIRRORS 8T - 5
(8) Remove screw holding mirror trim cover (Fig. (9) Disconnect power mirror wire harness at con-
5). nector in door.
(10) Pull harness up through door.
(11) Remove 3 screws holding mirror to door (Fig.
6).
Fig. 5 Power Mirror Trim Cover
Fig. 6 Power Mirror Remove/Install
(12) Reverse removal procedures to install.
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo