Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Mitsubishi Eclipse & Spyder 2000-2006 Approved Mitsubishi Eclipse & Spyder 2000-2002 31
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download 31 documenatation <<
Text preview - extract from the document
31-1
GROUP 31
WHEEL AND TIRE
CONTENTS
WHEEL AND TIRE DIAGNOSIS . . . . 31-2 WHEEL AND TIRE . . . . . . . . . . . . . . . 31-6
DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . . 31-2 INSTALLATION SERVICE POINT . . . . . . . 31-6
WHEEL BALANCE ACCURACY . . . . . . . . 31-3
SPECIFICATIONS . . . . . . . . . . . . . . . 31-7
ON-VEHICLE SERVICE. . . . . . . . . . . 31-6 FASTENER TIGHTENING
TIRE INFLATION PRESSURE CHECK . . . 31-6 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . 31-7
TIRE WEAR CHECK. . . . . . . . . . . . . . . . . . 31-6 GENERAL SPECIFICATIONS . . . . . . . . . . 31-7
WHEEL RUNOUT CHECK . . . . . . . . . . . . . 31-6 SERVICE SPECIFICATIONS . . . . . . . . . . . 31-7
31-2 WHEEL AND TIRE
WHEEL AND TIRE DIAGNOSIS
.
W H EEL A ND TIRE DIA G N O SIS
DIAGNOSIS
M1311000700028
SYMPTOM PROBABLE CAUSE REMEDY REFERENCE
PAGE
Rapid wear Under-inflation Adjust the tire P.31-6
at shoulders or lack of pressure.
rotation
ACX00923AB
ACX00924 AB
Rapid wear Over-inflation
at center or lack of
rotation
ACX00925 AB
ACX00926AB
Cracked Under-inflation Adjust the tire P.31-6
treads pressure.
ACX00927AB
Wear on one Excessive Check the camber. Refer to GROUP
side camber 33A, On-vehicle
Service - Front
Wheel Alignment
Check and
ACX00928 AB
Adjustment P.33A-
ACX00929 AB 6.
TSB Revision
WHEEL AND TIRE 31-3
WHEEL AND TIRE DIAGNOSIS
SYMPTOM PROBABLE CAUSE REMEDY REFERENCE
PAGE
Feathered Incorrect toe-in Adjust the toe-in.
edge
ACX00930AB
ACX00931 AB
Bald spots Unbalanced Balance the wheels. -
wheel
ACX00932AB
ACX00933 AB
Scalloped Lack of rotation of tires or worn Rotate the tires, Refer to GROUP
wear or out-of-alignment suspension check the front 33A, On-vehicle
suspension Service - Front
alignment. Wheel Alignment
Check and
ACX00934
Adjustment P.33A-
6.
WHEEL BALANCE ACCURACY
M1311001700010
PURPOSE PROCEDURE
This section contains tips and procedures for 1. Confirm that the balancer's cone and the wheel
achieving accurate wheel balance. Steering wheel mounting cone are undamaged and free of dirt
vibration and/or body shake can result if any of these and rust.
procedures are not carefully observed. 2. On this vehicle, the wheel's center hole on the
1. Wheels and tires must be properly mounted on a hub side has a chamfered edge. Use a back-
balancer in order to achieve correct balance. mounting cone on your wheel balancer to center
Centering the wheel on the shaft of the balancer is the wheel on the balancer shaft.
essential for proper mounting. 3. Install a wheel mounting cone. The appropriate
2. Off-the-car wheel balancers must be calibrated size cone for this vehicle is 67.0 mm (2.64
periodically to ensure good balancing results. An inches).
inaccurately calibrated balancer could cause 4. Before balancing the wheel, remove any wheel
unnecessary replacement of tires, shocks, weights from both sides. Also check both sides for
suspension components, or steering components. any damage.
Check your balancer's calibration approximately
5. When installing wheel weights, hammer them at a
every 100 balances. Your wheel balancer's
straight (not diagonal) angle.
instruction manual should include calibration
procedures. If the calibration procedures specifically
for your balancer are missing, use the generic steps
in this section for zero calibration, static balance, and
dynamic balance checks. The wheel balancer
calibration checks are also described in the
flowchart. (Refer to P.31-5.)
TSB Revision
31-4 WHEEL AND TIRE
WHEEL AND TIRE DIAGNOSIS
HUB/SHAFT CLAMPING CUP
ASSEMBLY
WING NUT
SPRING PLATE
WHEEL AC000041AB
MOUNTING STANDARD PASSENGER
CONE CAR WHEEL
2. Turn the wheel again 180 degree angle against
1. After balancing the wheel, loosen the wing nut the balancer's hub. If the wheel becomes out-of-
and turn the wheel 180 degree angle against the balance each time it is turned against the
balancer's hub. Then re-tighten the wing nut and balancer's hub, the wheel balancer may require
check the balance again. Repeat wheel balance if calibration.
necessary.
4. <>
1. Mount an undamaged original-equipment alloy Attach a 5-g (0.18-ounce) weight to the outer rim.
rim and tire assembly (wheel) onto your off-the- Recheck the balancer. The balancer should
car wheel balancer. Balance the wheel. detect 5 ◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo