Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan 350Z 2003-2007 Approved Nissan 350Z 2005 co
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download co documenatation <<
Text preview - extract from the document
ENGINE COOLING SYSTEM
B ENGINE
A
ENGINE COOLING SYSTEM
SECTION CO CO
C
D
E
CONTENTS
PRECAUTIONS ......................................................... 2. COOLING FAN ......................................................... 21
. F
Precautions for Supplemental Restraint System Removal and Installation ....................................... 21 .
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- REMOVAL .......................................................... 21
.
SIONER" ................................................................. 2
. INSTALLATION .................................................. 21 . G
Precautions for Battery Service ............................... 2 . Disassembly and Assembly ................................... 22 .
Precautions for Liquid Gasket ................................. 2 . DISASSEMBLY .................................................. 22 .
REMOVAL OF LIQUID GASKET SEALING ......... 2 . INSPECTION AFTER DISASSEMBLY ............... 22 .
H
LIQUID GASKET APPLICATION PROCEDURE 2 ..... ASSEMBLY ........................................................ 22.
PREPARATION .......................................................... 4
. WATER PUMP ......................................................... 23.
Special Service Tools .............................................. 4. Removal and Installation ....................................... 23 .
Commercial Service Tools ....................................... 5 . REMOVAL .......................................................... 23
. I
OVERHEATING CAUSE ANALYSIS ......................... 6 . INSPECTION AFTER REMOVAL ...................... 25 .
Troubleshooting Chart ............................................. 6 . INSTALLATION .................................................. 25 .
COOLING SYSTEM ................................................... 8 . INSPECTION AFTER INSTALLATION ............... 27 . J
Cooling Circuit ......................................................... 8
. WATER INLET AND THERMOSTAT ASSEMBLY ... 28
System Chart .......................................................... 9
. Removal and Installation ....................................... 28 .
ENGINE COOLANT ................................................. 10 . REMOVAL .......................................................... 28
.
K
Inspection .............................................................. 10
. INSPECTION AFTER REMOVAL ...................... 28 .
LEVEL CHECK .................................................. 10 . INSTALLATION .................................................. 29 .
LEAK CHECK .................................................... 10 . INSPECTION AFTER INSTALLATION ............... 29 .
Changing Engine Coolant ..................................... 10 . WATER OUTLET AND WATER PIPING .................. 30 . L
DRAINING ENGINE COOLANT ........................ 10 . Removal and Installation ....................................... 30 .
REFILLING ENGINE COOLANT ........................11 . REMOVAL .......................................................... 30
.
FLUSHING COOLING SYSTEM ........................ 12 . INSTALLATION .................................................. 31 . M
RADIATOR ............................................................... 13
. INSPECTION AFTER INSTALLATION ............... 31 .
Removal and Installation ....................................... 13 . SERVICE DATA AND SPECIFICATIONS (SDS) ..... 32 .
REMOVAL .......................................................... 13
. Standard and Limit ................................................. 32
.
INSTALLATION .................................................. 15 . ENGINE COOLANT CAPACITY (APPROXI-
INSPECTION AFTER INSTALLATION .............. 15 . MATE) ................................................................. 32
.
Checking Radiator Cap ......................................... 15 . RADIATOR ......................................................... 32
.
Checking Radiator ................................................. 15. THERMOSTAT ................................................... 32 .
RADIATOR (ALUMINUM TYPE) ............................. 17 . Tightening Torque .................................................. 32
.
Disassembly and Assembly .................................. 17 .
PREPARATION .................................................. 17 .
DISASSEMBLY .................................................. 17 .
ASSEMBLY ........................................................ 18.
INSPECTION ..................................................... 20 .
Revision: 2005 August CO-1 2005 350Z
PRECAUTIONS
PRECAUTIONS PFP:00001
Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" ABS00A3A
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
q Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Battery Service ABS00B4P
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Precautions for Liquid Gasket ABS009ZM
REMOVAL OF LIQUID GASKET SEALING
q After removing mounting bolts and nuts, separate the mating
surface using seal cutter [SST] and remove old liquid gasket
sealing.
CAUTION:
Be careful not to damage the mating surfaces.
q Tap seal cutter to insert it, and then slide it by tapping on the
side as shown in the figure.
q In areas where seal cutter [SST] is difficult to use, use plastic
hammer to lightly tap the parts, to remove it.
CAUTION: PBIC0002E
If for some unavoidable reason tool such as screwdriver is
used, be careful not to damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1. Using scraper, remove old liquid gasket adhering to the liquid
gasket application surface and the mating surface.
q Remove liquid gasket completely from the groove of the liquid
gasket application surface, mounting bolts, and bolt holes.
2. Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.
PBIC0003E
Revision: 2005 August CO-2 2005 350Z
PRECAUTIONS
3. Attach liquid gasket tube to tube presser [SST: WS39930000
( -- )]. A
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS" .
CO
4. Apply liquid gasket without breaks to the specified location with
the specified dimensions.
q If there is a groove for the liquid gasket application, apply liq-
C
uid gasket to the groove.
EMA0622D
D
q As for the bolt holes, normally apply liquid gasket inside the
holes. Occasionally, it should be applied outside the holes.
Make sure to read the text of service manual.
E
q Within five minutes of liquid gasket application, install the mat-
ing component.
q If liquid gasket protrudes, wipe it off immediately.
F
q Do not retighten mounting bolts or nuts after the installation.
q After 30 minutes or more have passed from the installation, fill
engine oil and engine coolant. G
CAUTION: SEM159F
If there are specific instructions in this manual, observe them.
H
I
J
K
L
M
Revision: 2005 August CO-3 2005 350Z
PREPARATION
PREPARATION PFP:00002
Special Service Tools ABS009ZN
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.) Description
Tool name
EG17650301 Adapting radiator cap tester to radiator cap
(J33984-A) and radiator filler neck
Radiator cap tester adapter a: 28 (1.10) dia.
b: 31.4 (1.236) dia.
c: 41.3 (1.626) dia.
Unit: mm (in)
S-NT564
KV99103510 Installing radiator upper and lower tanks
( -- )
Radiator plate pliers A
S-NT224
KV99103520 Removing radiator upper and lower tanks
( -- )
Radiator plate pliers B
S-NT225
KV10111100 Removing chain tensioner cover and water
(J37228) pump cover
Seal cutter
NT046
WS39930000 Pressing the tube of liquid gasket
( -- )
Tube presser
S-NT052
Revision: 2005 August CO-4 2005 350Z
PREPARATION
Commercial Service Tools ABS009ZO
A
Tool name Description
Radiator cap tester Checking radiator and radiator cap
CO
C
PBIC1982E
Power tool Loosening nuts and bolts D
E
PBIC0190E
F
G
H
I
J
K
L
M
Revision: 2005 August CO-5 2005 350Z
OVERHEATING CAUSE ANALYSIS
OVERHEATING CAUSE ANALYSIS PFP:00012
Troubleshooting Chart ABS009ZP
Symptom Check items
Water pump malfunction Worn or loose drive belt
Thermostat stuck closed --
Dust contamination or
Poor heat transfer Damaged fins paper clogging --
Physical damage
Clogged radiator cooling Excess foreign material
tube (rust, dirt, sand, etc.)
Cooling fan does not oper-
ate
Reduced air flow High resistance to fan rota- Fan assembly --
tion
Damaged fan blades
Damaged radiator shroud -- -- --
Improper engine coolant
Cooling sys- -- -- --
mixture ratio
tem parts
malfunction Poor engine coolant quality -- Engine coolant viscosity --
Loose clamp
Cooling hose
Cracked hose
Water pump Poor sealing
Loose
Radiator cap
Poor sealing
Engine coolant leaks
O-ring for damage, deterio-
Insufficient engine coolant ration or improper fitting
Radiator
Cracked radiator tank
Cracked radiator core
Reservoir tank Cracked reservoir tank
Cylinder head deterioration
Exhaust gas leaks into
Overflowing reservoir tank Cylinder head gasket dete-
cooling system
rioration
Revision: 2005 August CO-6 2005 350Z
OVERHEATING CAUSE ANALYSIS
Symptom Check items
A
High engine rpm under no
load
Driving in low gear for
Abusive driving CO
extended time
Driving at extremely high
speed
-- Overload on engine C
Powertrain system mal-
function
Installed improper size
Except cool- --
wheels and tires D
ing system
parts mal- Dragging brakes
function
Improper ignition timing
E
Blocked bumper --
Installed car brassiere
Blocked radiator grille Mud contamination or F
Blocked or restricted air paper clogging --
flow
Blocked radiator --
Blocked condenser G
Blocked air flow
Installed large fog lamp
H
I
J
K
L
M
Revision: 2005 August CO-7 2005 350Z
COOLING SYSTEM
COOLING SYSTEM PFP:21020
Cooling Circuit ABS009ZQ
PBIC2073E
Revision: 2005 August CO-8 2005 350Z
COOLING SYSTEM
System Chart ABS009ZR
A
CO
C
D
E
F
G
H
PBIC0847E I
J
K
L
M
Revision: 2005 August CO-9 2005 350Z
ENGINE COOLANT
ENGINE COOLANT PFP:KQ100
Inspection ABS009ZS
LEVEL CHECK
q Check if the reservoir tank engine coolant level is within the
"MIN" to "MAX" range when engine is cool.
q Adjust the engine coolant level as necessary.
SMA412B
LEAK CHECK
q To check for leaks, apply pressure to the cooling system with
radiator cap tester (commercial service tool) and radiator cap
tester adapter [SST].
Testing pressure
: 157 kPa (1.6 kg/cm2 , 23 psi)
WARNING:
Do not remove radiator cap when engine is hot. Serious
burns could occur from high-pressure engine coolant
escaping from radiator.
CAUTION: SLC756A
Higher test pressure than specified may cause radiator
damage.
NOTE:
In a case that engine coolant decreases, replenish radiator with engine coolant.
q If anything is found, repair or replace damaged parts.
Changing Engine Coolant ABS009ZT
WARNING:
q To avoid being scalded, do not change engine coolant when engine is hot.
q Wrap a thick cloth around cap and carefully remove cap. First, turn cap a quarter of a turn to
release built-up pressure. Then turn cap all the way.
CAUTION:
Be careful not to allow engine coolant to contact drive belts.
DRAINING ENGINE COOLANT
1. Remove undercover with power tool.
2. Open radiator drain plug at the bottom of radiator, and then
remove radiator cap.
PBIC0893E
When drain all of engine coolant in the system, open water drain plugs on engine cylinder block.
Refer to EM-140, "DISASSEMBLY" .
Revision: 2005 August CO-10 2005 350Z
ENGINE COOLANT
3. Remove reservoir tank as necessary, and drain engine coolant and clean reservoir tank before installing.
4. Check drained engine coolant for contaminants such as rust, corrosion or discoloration. A
If contaminated, flush the engine cooling system. Refer to CO-12, "FLUSHING COOLING SYSTEM" .
REFILLING ENGINE COOLANT
CO
1. Install reservoir tank if removed, and radiator drain plug.
CAUTION:
Be sure to clean drain plug and install with new O-ring.
C
Radiator drain plug:
: 0.78 - 1.6 N◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo