Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan 350Z 2003-2007 Approved Nissan 350Z 2005 ww

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download ww documenatation <<

Text preview - extract from the document

WIPER, WASHER & HORN

K ELECTRICAL

SECTION
WIPER, WASHER & HORN
WW B

E
CONTENTS
PRECAUTION ........................................................... 3 . Only Front Wiper Hi Does Not Operate ................. 26 . F
Precautions for Supplemental Restraint System Only Front Wiper Intermittent Does Not Operate ... 28
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Front Wiper Interval Time Is Not Controlled by Vehi-
SIONER" ................................................................. 3
. cle Speed ............................................................... 28
. G
Precautions for Battery Service ............................... 3 . Front Wiper Intermittent Operation Switch Position
FRONT WIPER AND WASHER SYSTEM ................. 4 . Cannot Be Adjusted ............................................... 28 .
Components Parts and Harness Connector Loca- Wiper Does Not Wipe When Front Washer Operates
H
tion .......................................................................... 4
. ... 29
System Description ................................................. 4 . After Front Wiper Operate for 10 Seconds, They
OUT LINE ............................................................. 4
. Stop for 20 Seconds, and After Repeating the Oper-
LOW SPEED WIPER OPERATION ..................... 5 . ations Five Times, They Become Inoperative ....... 30 . I
HIGH SPEED WIPER OPERATION .................... 5 . Front Wiper Does Not Stop .................................... 31 .
INTERMITTENT OPERATION ............................. 5 . Removal and Installation of Front Wiper Arms,
AUTO STOP OPERATION ................................... 6 . Adjustment of Wiper Arms Stop Location .............. 31 . J
WASHER OPERATION ........................................ 6 . REMOVAL .......................................................... 31 .
MIST OPERATION ............................................... 6 . INSTALLATION .................................................. 31 .
FAIL-SAFE FUNCTION ........................................ 7 . ADJUSTMENT ................................................... 32 .
WW
COMBINATION SWITCH READING FUNCTION 7 ..... Removal and Installation of Front Wiper Motor and
CAN Communication System Description ............... 9 . Linkage .................................................................. 32
.
CAN Communication Unit ....................................... 9 . REMOVAL .......................................................... 32 .
Schematic ............................................................. 10. INSTALLATION .................................................. 32 . L
Wiring Diagram -- WIPER -- ................................11 . Disassembly and Assembly Front Wiper Motor and
Terminals and Reference Values for BCM ............ 14 . Linkage .................................................................. 33
.
Terminals and Reference Values for IPDM E/R .... 15 . DISASSEMBLY .................................................. 33 . M
How to Proceed With Trouble Diagnosis ............... 15 . ASSEMBLY ........................................................ 33 .
Preliminary Check ................................................. 15 . Washer Nozzle Adjustment ................................... 34 .
CHECK POWER SUPPLY AND GROUND CIR- Washer Tube Layout ............................................. 35 .
CUIT ................................................................... 15
. Removal and Installation of Front Washer Nozzle... 35
CONSULT-II Functions (BCM) .............................. 17 . Removal and Installation of Front Washer Tube
CONSULT-II BASIC OPERATION ...................... 17 . Joint ....................................................................... 35
.
WORK SUPPORT .............................................. 18 . REMOVAL .......................................................... 35 .
DATA MONITOR ................................................ 18 . INSTALLATION .................................................. 35 .
ACTIVE TEST .................................................... 19 . Inspection of Washer Nozzle ................................. 35 .
CONSULT-II Functions (IPDM E/R) ...................... 20 . CHECK VALVE ................................................... 35 .
CONSULT-II BASIC OPERATION ...................... 20 . Removal and Installation of Front Wiper and Washer
DATA MONITOR ................................................ 21 . Switch .................................................................... 36
.
ACTIVE TEST .................................................... 21 . REMOVAL .......................................................... 36 .
Front Wiper Does Not Operate ............................. 22 . INSTALLATION .................................................. 36 .
Front Wiper Does Not Return to Stop Position ...... 24 . Removal and Installation of Washer Tank ............. 36 .
Only Front Wiper Low Does Not Operate ............. 25 . REMOVAL .......................................................... 36 .

Revision: 2005 August WW-1 2005 350Z
INSTALLATION ................................................... 37 . ment of Wiper Arms Stop Location ........................50 .
Removal and Installation of Washer Pump ............ 37 . Removal and Installation of Rear Wiper Motor ......51 .
REMOVAL .......................................................... 37 . REMOVAL ...........................................................51 .
INSTALLATION ................................................... 37 . INSTALLATION ...................................................52 .
REAR WIPER AND WASHER SYSTEM ................. 38 . Washer Nozzle Adjustment ....................................52 .
Components Parts and Harness Connector Loca- Washer Tube Layout ..............................................53 .
tion ......................................................................... 38
. Check Valve ...........................................................53
.
System Description ................................................ 38 . Removal and Installation of Rear Wiper and Washer
OUT LINE ........................................................... 38 . Switch ....................................................................53
.
BCM WIPER SWITCH READING FUNCTION ... 39 Removal and Installation of Washer Tank ..............53 .
Wiring Diagram -- WIP/ R -- ................................ 40 . Removal and Installation of Washer Pump ............53 .
Terminals and Reference Values for BCM ............. 42 . POWER SOCKET ....................................................54 .
How to Proceed With Trouble Diagnosis ............... 43 . Wiring Diagram -- P/SCKT -- ...............................54 .
Preliminary Check ................................................. 43 . Removal and Installation (Luggage Floor Finisher
CHECK POWER SUPPLY AND GROUND CIR- Lower) ....................................................................55
.
CUIT ................................................................... 43
. REMOVAL ...........................................................55 .
CONSULT-II Functions (BCM) ............................... 44 . INSTALLATION ...................................................55 .
CONSULT-II BASIC OPERATION ...................... 44 . Removal and Installation (Instrument Passenger
DATA MONITOR ................................................. 45 . Panel Lower) ..........................................................55
.
ACTIVE TEST .................................................... 46 . REMOVAL ...........................................................55 .
Rear Wiper Does Not Operate .............................. 46 . INSTALLATION ...................................................55 .
Rear Wiper Does Not Return to Stop Position ....... 48 . HORN .......................................................................56
.
Only Rear Wiper ON Does Not Operate ................ 49 . Wiring Diagram -- HORN -- .................................56 .
Only Rear Wiper INT Does Not Operate ............... 49 . Removal and Installation ........................................57 .
Wiper Does Not Wipe When Rear Washer Operates 49 ... REMOVAL ...........................................................57 .
Rear Wipers Do Not Stop ...................................... 50 . INSTALLATION ...................................................57 .
Removal and Installation of Rear Wiper Arm, Adjust-

Revision: 2005 August WW-2 2005 350Z
PRECAUTION

PRECAUTION PFP:00011
A
Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" AKS00AC5

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along B
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front C
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING: D
q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer. E
q Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section. F
q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
G
Precautions for Battery Service AKS003RE

Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the H
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
I

Revision: 2005 August WW-3 2005 350Z
FRONT WIPER AND WASHER SYSTEM

FRONT WIPER AND WASHER SYSTEM PFP:28810

Components Parts and Harness Connector Location AKS000Y6

PKIB2146E

System Description AKS000Y7

q All front wiper relays (HI, LO) are included in IPDM E/R (intelligent power distribution module engine
room).
q Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input termi-
nals. Terminal combination status is read by BCM (body control module) when switch is turned ON.
q BCM controls front wiper LO, HI, and INT (intermittent) operation.
q IPDM E/R operates wiper motor according to CAN communication signals from BCM.
OUT LINE
Power is supplied at all times
q through 40 A fusible link (letter F, located in fuse, fusible link and relay box)
q to BCM terminal 55,
q through 10 A fuse [No.18 located in fuse block (J/B)]
q to BCM terminal 42,
q through 20 A fuse (No.73 located in IPDM E/R)
q to front wiper relay, located in IPDM E/R,
q through 15 A fuse (No.78 located in IPDM E/R)
q to CPU located in IPDM E/R,
q through 10 A fuse (No.71 located in IPDM E/R)
q to CPU located in IPDM E/R.
When ignition switch is in ON or START position, power is supplied
Revision: 2005 August WW-4 2005 350Z
FRONT WIPER AND WASHER SYSTEM

q to ignition relay, located in IPDM E/R, from battery direct
q through 10 A fuse [No.1 located in fuse block (J/B)] A
q to BCM terminal 38,
q through ignition relay, located in IPDM E/R
B
q to front wiper relay, located in IPDM E/R
q to front wiper high relay, located in IPDM E/R
q to CPU located in IPDM E/R, C
q through 10 A fuse (No.84 located in IPDM E/R)
q through IPDM E/R terminal 44
q to front washer motor terminal 2. D
Ground is supplied
q to BCM terminal 52
q through grounds M30 and M66, E
q to IPDM E/R terminals 38 and 60
q through grounds E17, E43 and F152,
F
q to combination switch terminal 12
q through grounds M30 and M66.
LOW SPEED WIPER OPERATION G
When the front wiper switch is in low position, BCM detect low speed wiper ON signal by BCM wiper switch
reading function.
BCM sent front wiper request signal (LOW) with CAN communication line H
q from BCM terminals 39 and 40
q to IPDM E/R terminals 48 and 49.
When the IPDM E/R receives front wiper request signal (LOW), it turns ON front wiper relay, located in the I
IPDM E/R, power is supplied
q to front wiper motor terminal 3
q through IPDM E/R terminal 21 and front wiper high relay and front wiper relay. J
Ground is supplied
q to front wiper motor terminal 4
WW
q through grounds E17, E43 and F152.
with power and ground is supplied, front wiper motor operates at low speed.
HIGH SPEED WIPER OPERATION L
When the front wiper switch is in HI position, BCM detect high speed wiper ON signal by BCM wiper switch
reading function.
BCM sent front wiper request signal (HI) with CAN communication line M
q from BCM terminals 39 and 40
q to IPDM E/R terminals 48 and 49.
When the IPDM E/R receives front wiper request signal (HI), it turns ON front wiper relay, located in IPDM E/
R, power is supplied
q to front wiper motor terminal 2
q through IPDM E/R terminal 31 and front wiper high relay and front wiper relay.
Ground is supplied
q to front wiper motor terminal 4
q through grounds E17, E43 and F152.
with power and ground is supplied, front wiper motor operates at high speed.
INTERMITTENT OPERATION
Front wiper intermittent operation delay interval is determined from a combination of 3 switches (intermittent
operation dial position 1, 2, and 3) and vehicle speed signal.
After each intermittent operation delay interval, BCM sends front wiper request signal to IPDM E/R.

Revision: 2005 August WW-5 2005 350Z
FRONT WIPER AND WASHER SYSTEM

Wiper Dial Position Setting
Combination switch
Intermittent operation
Wiper dial position Intermittent operation Intermittent operation Intermittent operation
interval
dial position 1 dial position 2 dial position 3
1 Short ON ON ON
2 ON ON OFF
3 ON OFF OFF

4 OFF OFF OFF

5 OFF OFF ON
6 OFF ON ON
7 Long OFF ON OFF

Example: For wiper dial position 1
Using combination switch reading function, BCM detects ON/OFF status of intermittent operation dial posi-
tions 1, 2, and 3.
When combination switch status is as listed below, BCM determines that it is wiper dial position 1.
q Intermittent operation dial position 1: ON (Continuity exists between combination switch output 3 and input
1.)
q Intermittent operation dial position 2: ON (Continuity exists between combination switch output 5 and input
1.)
q Intermittent operation dial position 3: ON (Continuity exists between combination switch output 4 and input
2.)
BCM determines front wiper intermittent operation delay interval from wiper dial position 1 and vehicle speed,
and sends wiper request signal (INT) to IPDM E/R.
AUTO STOP OPERATION
With wiper switch turned OFF, wiper motor will continue to operate until wiper arms reach windshield base.
When the wiper arms are not located at base of windshield with wiper switch OFF, ground is provided
q from IPDM E/R terminal 21
q to front wiper motor terminal 3, in order to continue wiper motor operation at low speed
q to IPDM E/R terminal 32
q through front wiper motor terminals 1 and 4
q through grounds E17, E43 and F152.
When the wiper arms reach base of windshield, front wiper motor terminals 1 and 4 are connected, and
ground is supplied
Then the IPDM E/R sends auto stop operation signal to BCM with CAN communication line.
When the BCM receives auto-stop operation signal, BCM sends wiper stop signal to IPDM E/R with CAN com-
munication line.
IPDM E/R stops wiper motor. Wiper motor will then stop wiper arms at the STOP position.
WASHER OPERATION
When the wiper switch is in front wiper washer position, BCM detect front wiper washer signal by BCM wiper
switch reading function. (Refer to WW-7, "COMBINATION SWITCH READING FUNCTION" )
Combination switch ground is supplied
q to front washer motor terminal 1
q through combination switch terminal 11
q to combination switch terminal 12
q through grounds M30 and M66.
With ground is supplied, front washer motor is operated.
When the BCM detects that front washer motor has operated for 0.4 seconds or longer, BCM operates front
wiper motor for low speed.
When the BCM detects washer switch is OFF, low speed operation cycles approximately 2 times and stops.
MIST OPERATION
When the wiper switch is turned to the mist position, wiper low speed operation cycles once and then stops.
Revision: 2005 August WW-6 2005 350Z
FRONT WIPER AND WASHER SYSTEM

For additional information about wiper operation under this condition, refer to WW-5, "LOW SPEED WIPER
OPERATION" . A
If switch is held in mist position, low speed operation continues.
FAIL-SAFE FUNCTION
If an abnormality occurs in CAN communications, IPDM E/R holds the condition just before fail-safe status is B
initiated until ignition switch is turned off. (If wipers were operating in LO just before the initiation of fail-safe
status, they continue to operate in LO until ignition switch is turned OFF)
COMBINATION SWITCH READING FUNCTION C
Description
q BCM reads combination switch (wiper) status, and controls related systems such as headlamps and wip-
D
ers, according to the results.
q BCM reads information of a maximum of 20 switches by combining five output terminals (OUTPUT 1-5)
and five input terminals (INPUT 1-5).
E
Operation Description
q BCM activates transistors of output terminals (OUTPUT 1-5) periodically, and allows current to flow in
turn. F
q If any (1 or more) switches are turned ON, circuit of output terminals (OUTPUT 1-5) and input terminals
(INPUT 1-5) becomes active.
q At this time, transistors of output terminals (OUTPUT 1-5) are activated to allow current to flow. When volt- G
age of input terminals (INPUT 1-5) corresponding to that switch changes, interface in BCM detects volt-
age change, and BCM determines that switch is ON.
H

PKIA7241E

Revision: 2005 August WW-7 2005 350Z
FRONT WIPER AND WASHER SYSTEM

BCM - Operation Table of Combination Switches
q BCM reads operation status of combination switch using combinations shown in table below.

PKIA7242E

Sample Operation: (When Wiper Switch Turned to LOW Position)
q When wiper switch is turned to LOW position, front wiper LOW contact in combination switch turns ON. At
this time if OUTPUT 1 transistor is activated, BCM detects that voltage changes in INPUT 3.
q When BCM detects that voltage changes in INPUT 3 while OUTPUT 1 transistor is ON, it judges that front
wiper switch is in LOW position. Then BCM sends front wiper request signal (LO) to IPDM E/R using CAN
communication.
q If BCM detects that voltage changes in INPUT 3 when OUTPUT 1 transistor is activated again, it recog-
nizes that wiper switch is still in LOW position.

PKIA7243E

Revision: 2005 August WW-8 2005 350Z
FRONT WIPER AND WASHER SYSTEM

NOTE:
Each OUTPUT terminal transistor is activated at 10 ms intervals. Therefore after switch is turned ON, electri- A
cal loads are activated with time delay. But this time delay is so short that it cannot be detected by human
senses.
Operation Mode B
Combination switch reading function has operation modes shown below.
1. Normal status
q When BCM is not in sleep status, OUTPUT terminals (1-5) each turn ON-OFF every 10 ms.
C
2. Sleep status
q When BCM is in sleep status, transistors of OUTPUT (1 and 5) stop the output, and BCM enters low
D
current consumption mode. OUTPUT (2, 3, and 4) turn ON-OFF every 60 ms, and only input from light
switch system is accepted.

PKIB6124E
M
CAN Communication System Description AKS000Y8

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Unit AKS003M9

Refer to LAN-21, "CAN Communication Unit" .

Revision: 2005 August WW-9 2005 350Z
FRONT WIPER AND WASHER SYSTEM

Schematic AKS000Y9

TKWT2315E

Revision: 2005 August WW-10 2005 350Z
FRONT WIPER AND WASHER SYSTEM

Wiring Diagram -- WIPER -- AKS000YA

TKWT1853E

Revision: 2005 August WW-11 2005 350Z
FRONT WIPER AND WASHER SYSTEM

TKWT2316E

Revision: 2005 August WW-12 2005 350Z
FRONT WIPER AND WASHER SYSTEM

TKWT2317E

Revision: 2005 August WW-13 2005 350Z
FRONT WIPER AND WASHER SYSTEM

Terminals and Reference Values for BCM AKS00APG

Measuring condition
Terminal Wire
Signal name Ignition Reference value
No. color Operation or condition
switch

Lighting switch and wiper switch OFF
2 GY Combination switch input 5 ON
Wiper dial position 4

SKIA5291E

Lighting switch and wiper switch OFF
3 L/W Combination switch input 4 ON
Wiper dial position 4

SKIA5292E

Lighting switch and wiper switch OFF
4 PU/W Combination switch input 3 ON
Wiper dial position 4

SKIA5291E

5 Y/R Combination switch input 2 ON

Lighting switch and wiper switch OFF
6 Y/G Combination switch input 1 ON Wiper dial position 4

SKIA5292E

Lighting switch and wiper switch OFF
32 G/B Combination switch output 5 ON
Wiper dial position 4

SKIA5291E

Lighting switch and wiper switch OFF
33 G Combination switch output 4 ON
Wiper dial position 4

SKIA5292E

Lighting switch and wiper switch OFF
34 W/L Combination switch output 3 ON
Wiper dial position 4

SKIA5291E

Revision: 2005 August WW-14 2005 350Z
FRONT WIPER AND WASHER SYSTEM

Measuring condition
Terminal Wire A
Signal name Ignition Reference value
No. color Operation or condition
switch
35 W/G Combination switch output 2
B

Lighting switch and wiper switch OFF
ON
36 W/R Combination switch output 1 Wiper dial position 4
C

SKIA5292E

38 W/L Ignition switch (ON) ON -- Battery voltage D
39 L CAN- H -- -- --
40 P CAN- L -- -- --
E
42 GY Battery power supply OFF -- Battery voltage
52 B Ground ON -- Approx. 0V
55 R Battery power supply OFF -- Battery voltage F
Terminals and Reference Values for IPDM E/R AKS00APH

Measuring condition G
Terminal Wire
Signal name Ignition Reference value
No. color Operation or condition
switch
OFF Approx. 0V H
21 PU Low speed signal ON Wiper switch
LOW Battery voltage
OFF Approx. 0V
31 L/B High speed signal ON Wiper switch I
HI Battery voltage
Wiper operating Battery voltage
32 L/Y Wiper auto - stop signal ON
Wiper stopped Approx. 0V J
38 B Ground ON -- Approx. 0V
44 OR Washer motor power supply ON -- Battery voltage
WW
48 L CAN- H -- -- --
49 P CAN- L -- -- --
60 B Ground ON -- Approx. 0V L
How to Proceed With Trouble Diagnosis AKS00API

1. Confirm the symptoms and customer complaint.
M
2. Understand operation description and function description. Refer to WW-4, "System Description" .
3. Perform preliminary check. Refer to WW-15, "Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction.
5. Does the front wiper and washer operate normally? If YES, GO TO 6. If NO, GO TO 4.
6. INSPECTION END
Preliminary Check AKS00APJ

CHECK POWER SUPPLY AND GROUND CIRCUIT
1. CHECK FUSE
q Check for blown fuses.
Unit Power source Fuse and fusible link No.
Front washer motor Ignition switch ON or START 84
Front wiper motor, front wiper relay, front wiper HI relay Battery 73

Revision: 2005 August WW-15 2005 350Z
FRONT WIPER AND WASHER SYSTEM

Unit Power source Fuse and fusible link No.
F
Battery
BCM 18
Ignition switch ON or START 1
Refer to WW-11, "Wiring Diagram -- WIPER --" .
OK or NG
OK >> GO TO 2
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse, Refer to PG-
3, "POWER SUPPLY ROUTING CIRCUIT" .

2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check voltage between BCM harness connector terminal and
ground.
Terminal Ignition switch position
(+)
Terminal (-) OFF ON
Connector
(Wire color)
M91 42 (GY) Battery voltage Battery voltage PKIB5199E

M91 55 (R) Ground Battery voltage Battery voltage
M90 38 (W/L) Approx. 0V Battery voltage
OK or NG
OK >> GO TO 3.
NG >> Check harness for open or short between fuse, fusible link and BCM.

3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
Terminal
Continuity
Connector Terminal (Wire color)
Ground
M91 52 (B) Yes
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.

PKIB5198E

Revision: 2005 August WW-16 2005 350Z
FRONT WIPER AND WASHER SYSTEM

CONSULT-II Functions (BCM) AKS00APK

A
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
BCM diagnosis position Diagnosis mode Description
WORK SUPPORT Changes the setting for each function. B
WIPER DATA MONITOR Displays BCM input data in real time.
ACTIVE TEST Device operation can be checked by applying a drive signal to device.
C
SELF-DIAG RESULTS BCM performs self-diagnosis of CAN communication.
BCM
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.

D
CONSULT-II BASIC OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication. E
1. With ignition switch OFF, connect CONSULT-II and CONSULT-II
CONVERTER to data link connector, then turn ignition switch
ON. F

PBIB1069E

2. Touch "START (NISSAN BASED VHCL)". I

BCIA0029E
L

3. Touch "BCM" on "SELECT SYSTEM" screen.
If "BCM" is not displayed, print "SELECT SYSTEM" screen, then M
refer to GI-39, "CONSULT-II Data Link Connector (DLC) Circuit"
.

BCIA0030E

Revision: 2005 August WW-17 2005 350Z
FRONT WIPER AND WASHER SYSTEM

4. Touch "WIPER" on "SELET TEST ITEM" screen.

PKIA6100E

WORK SUPPORT
Operation Procedure
1. Touch "WIPER" on "SELECT TEST ITEM" screen.
2. Touch "WORK SUPPORT" on "SELECT DIAG MODE" screen.
3. Touch "WIPER SPEED SETTING" on "SELECT WORK ITEM" screen.
4. Touch "START".
5. Touch "CHANGE SETT".
6. The setting will be changed and "CUSTOMIZING COMPLETED" will be displayed.
7. Touch "END".
Display Item List
Item Description CONSULT-II Factory setting

WIPER SPEED Vehicle speed sousing type wiper control mode can be changed in this ON

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo