Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan 300ZX 1984-1985,1988,1990,1994-1996 Approved 1984 General Info
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download General Info documenatation <<
Text preview - extract from the document
GENERAL INFORMATION
CONTENTS
PRECAUTIONS GI- 2
HOW TO USE THIS M A N U A L . . GI- 5
IDENTIFICATION INFORMATION . GI- 8
RECOMMENDED FUEL AND LUBRICANTS . GI-14
LIFTING, TOWING A N D TIE-DOWN POINTS GI-15
TIGHTENING TORQUE OF STANDARD BOLT GI-17
PRECAUTIONS
ObSeNe the following precautions that are not de- 3 When removing a heavy component such as the
scribed in each individual section t o ensure safe engine or transaxle/transmission, take care not
and proper service operations to lose your balance and drop it or cause it to
1 Do not operate the engine for an extended h i t against adjacent parts, especially against the
period of time without proper exhaust ventila- brake parts such as brake tube and master
tion cylinder.
Keep the work area well ventilated and free of Before starting repairs which do not require
any inflammable materials Special care should battery power, always turn o f f the ignition
be taken when handling any inflammable or switch, then disconnect the ground cable from
poisonous materials, such as gasoline, refrige- the battery t o prevent accidental short circuit
rant gas, etc If you are working in a p i t or
other enclosed area, be sure t o properly venti-
late before working with hazardous materials
Do not smoke while working on the vehicle.
2
i-:
Before jacking up the vehicle, apply wheel
SO1285
chocks or other tire blocks t o the wheels t o
prevent the vehicle from moving After jacking
up the vehicle, support the vehicle weight with
To prevent serious burns, avoid contact with
hot metal parts such as the radiator, exhaust
manifold, t a i l pipe and muffler
Do not remove the radiator cap when the
engine is hot
rigid racks a t the points designated for proper
lifting and towing before working on the
vehicle
These operations should be done on a level sur-
face
6 To prevent scratches and soiling, protect fen-
ders, upholstery and carpeting with appropriate
covers before starting servicing
Take caution that keys, buckles or buttons on
SGi231 your person d o not scratch the paint
GI-2
PRECAUTIONS
Precautions for a Catalyst -
TSeat caw If a large amount o f unburned fuel flows into con-
verter, the converter temperature will be excessive-
ly high To prevent this, follow the procedure
below
Use unleaded gasoline only Leaded gasoline
will seriously damage catalytic converter
When checking for ignition spark or measuring
engine compression, make tests quickly and
only when necessary.
Do not run engine with low fuel in the fuel
tank, otherwise engine may misfire causing
861234 damage to the converter
Do not place vehicle on inflammable material
Keep inflammable material off exhaust pipe
7 Clean all disassembled parts in the designated
liquid or solvent prior to inspection or assem-
bly
8 Replace oil seals, gaskets, packings, O-rings,
locking washers, cotter pins, self-locking nuts,
etc as instructed and discard used ones
9 Tapered roller bearings and needle bearings
should be replaced as a set of inner and outer
races
10 Arrange the disassembled parts in accordance
with their assembled locations and sequence
11 Do not touch the terminals of electrical com-
ponents which utilize microcomputers such as Clean floor
SGi290
electronic control units Static electrical
charges stored in your body may damage inter-
nal electronic components
12 After disconnecting vacuum hose or air hose,
attach tag which indicates the proper connec-
tion t o prevent incorrect connection
13 Use only the lubricants specified in the applica-
ble section or those indicated under "Recom-
mended Fuel and Lubricants"
14 Use approved bonding agent, sealants or their
equivalents when required
15 The use of the proper tools and recommended
essential tools should be used where specified
for proper, safe and efficient service repairs
16 When effecting repairs on the fuel, oil, water,
vacuum or exhaust systems, make certain to
check a l l affected lines for leaks
17. Dispose of drained oil or the solvent used for
cleaning parts in an appropriate manner
GI-3
PRECAUTIONS
Precautions for E.F.I. or -Precautions for Turbocharger -
E.C.C.S. Engine
The turbocharger system uses engine oil for lubri-
cation and cooling of i t s rotating components The
Before connecting or disconnecting E F.I. or
turbocharger turbine turns a t a speed in excess of
E C C.S. harness connector to or from any
100,000 rpm a t full throttle and i t s temperature
E F I. or E C C S unit, be sure t o turn the
can reach 870◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo