Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Murano 2003-2007.2009 Approved Nissan Murano 2005 RFD
<< Back |
HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download
Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing.
If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download RFD documenatation <<Text preview - extract from the documentREAR FINAL DRIVE
D DRIVELINE/AXLE
A
SECTION RFD
REAR FINAL DRIVE
B
C
RFD
E
CONTENTS
PRECAUTIONS ......................................................... 2
. Components .......................................................... 13
. F
Precautions ............................................................. 2
. Pre-Inspection ....................................................... 14
.
PREPARATION .......................................................... 3
. TOTAL PRELOAD .............................................. 14 .
Special Service Tools .............................................. 3
. DRIVE GEAR TO DRIVE PINION BACKLASH ... 15 G
Commercial Service Tools ....................................... 6 . DRIVE GEAR RUNOUT ..................................... 16 .
NOISE, VIBRATION AND HARSHNESS (NVH) COMPANION FLANGE RUNOUT ...................... 16 .
TROUBLESHOOTING ............................................... 7 . TOOTH CONTACT ............................................. 16 .
H
NVH Troubleshooting Chart .................................... 7 . Disassembly and Assembly ................................... 19 .
FRONT OIL SEAL ..................................................... 8. DISASSEMBLY .................................................. 19 .
Removal and Installation ......................................... 8. ASSEMBLY ........................................................ 22
.
REMOVAL ............................................................ 8
. SERVICE DATA AND SPECIFICATIONS (SDS) ..... 29 . I
INSTALLATION .................................................... 9
. General Specification ............................................ 29.
SIDE OIL SEAL ....................................................... 10
. Drive Gear Runout ................................................. 29
.
Removal and Installation ....................................... 10 . Side Gear Adjustment ........................................... 29 . J
REMOVAL .......................................................... 10
. AVAILABLE SIDE GEAR THRUST WASHERS... 29
INSTALLATION .................................................. 10. Drive Pinion Adjustment ........................................ 29 .
REAR FINAL DRIVE ASSEMBLY ............................11 . AVAILABLE DRIVE PINION ADJUSTING SHIM 29 ...
K
Removal and Installation ........................................11 . Side Bearing Preload Adjustment .......................... 29 .
REMOVAL ...........................................................11
. AVAILABLE SIDE BEARING ADJUSTING SHIM 30 ...
INSTALLATION .................................................. 12. Total Preload .......................................................... 30
.
L
M
Revision: 2004 November RFD-1 2004 Murano
PRECAUTIONS
PRECAUTIONS PFP:00001
Precautions ADS000W5
CAUTION:
q Check for the correct installation status prior removal or disassembly. When mating marks are
required, be sure they do not interfere with the function of the parts they are applied to.
q Carry out an overhaul in a clean work place, Using a dust proof room is recommended.
q Before disassembly, using steam or white gasoline, completely remove sand and mud from the
exterior the unit, preventing them from entering into the unit during disassembly or assembly.
q Check appearance of the disassembled parts for damage, deformation, and abnormal wear. If a
malfunction is detected, replace it with a new one.
q Normally replace lock pins, oil seals, and bearings with new ones every times they are removed.
q In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to out-
side. If tightening sequence is specified, observe it.
q Clean and flush the parts sufficiently and blow them dry.
q Be careful not to damage the sliding surfaces and mating surface.
q When applying sealant, remove the old sealant from the mounting surface; then remove any mois-
ture, oil, and foreign materials from the application and mounting surfaces.
q Always use shop paper for cleaning the inside of components.
q Avoid using cotton gloves or a shop cloth to prevent entering of lint.
q During assembly, observe the specified tightening torque, and new differential oil, Vaseline, or
multi-purpose grease, as specified for each vehicle, when necessary.
Revision: 2004 November RFD-2 2004 Murano
PREPARATION
PREPARATION PFP:00002
A
Special Service Tools ADS000EE
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number (Kent-Moore No.)
B
Description
Tool name
KV38108300 (
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo