Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Micra 2003-2006 Approved 03k12e SE

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download SE documenatation <<

Text preview - extract from the document

SEAT

I BODY

B
SECTION
SEAT C

E
CONTENTS
PRECAUTIONS ......................................................... 2. SEATBACK TRIM PAD ......................................... 8 . F
Precautions for Supplemental Restraint System SEATBACK FRAME ............................................. 9 .
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Disassembly and Assembly of Seat Cushion .......... 9 .
SIONER" ................................................................. 2
. SEAT CUSHION TRIM PAD ................................. 9 . G
Precautions ............................................................. 2
. SEAT CUSHION FRAME ..................................... 9 .
CLIP AND FASTENER .............................................. 3 . REAR SEAT ............................................................. 11
.
List of Table ............................................................. 3
. Component Parts Location .................................... 11 .
H
HEATED SEAT .......................................................... 4
. BENCH SEAT ..................................................... 11
.
Description .............................................................. 4
. SPLIT SEAT ....................................................... 12
.
Wiring Diagram -- H/SEAT ..................................... 5 . SLIDE SEAT ....................................................... 13
.
FRONT SEAT ............................................................. 7
. Removal and Installation ....................................... 13. SE
Component Parts Location ...................................... 7 . REMOVAL .......................................................... 13
.
Removal and Installation ......................................... 8 . INSTALLATION .................................................. 15
.
REMOVAL ............................................................ 8
. REAR SEATBACK DISASSEMBLY AND J
INSTALLATION .................................................... 8 . ASSEMBLY ........................................................ 16
.
Disassembly and Assembly of Seatback ................ 8 .
K

SE-1
PRECAUTIONS

PRECAUTIONS PFP:00001

Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EIS004P3

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
q Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions EIS004P4

q When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which
may get in the way with cloth.
q When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.
q Keep removed parts protected with cloth.
q If a clip is deformed or damaged, replace it.
q If an unreusable part is removed, replace it with a new one.
q Tighten bolts and nuts firmly to the specified torque.
q After re-assembly has been completed, make sure each part functions correctly.
q Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
q Do not use any organic solvent, such as thinner or benzine.

SE-2
CLIP AND FASTENER

CLIP AND FASTENER PFP:76906
A
List of Table EIS004ON

MIIB0032E

SE-3
HEATED SEAT

HEATED SEAT PFP:87335

Description EIS004P5

q When handling seat, be extremely careful not to scratch heating unit.
q To replace heating unit, seat trim and pad should be separated.
q Do not use any organic solvent, such as thinner, benzene, alcohol, etc. to clean trims.

SBT314

SE-4
HEATED SEAT

Wiring Diagram -- H/SEAT SMA for VIN >SJN**AK12U1309269 EIS004P6

MKWA1815E

SE-5
HEATED SEAT

MKWA0836E

SE-6
FRONT SEAT

FRONT SEAT PFP:87000
A
Component Parts Location SMA for VIN >SJN**AK12U1277776 EIS004OP

CAUTION:
When removing and installing seats, use shop cloths to protect the parts from damage.
B

M
MIIB0033E

1. Headrest 2. Headrest holder (free) 3. Headrest holder (locked)
4. Seatback trim & pad 5. Side air bag module 6. Fixed inner cross rod
7. Seatback frame 8. Plastic collar 9. Reclining dial
10. Seat slide outer finisher 11. Slide inner cover 12. Spring
13. Seat slide assembly 14. Seat slide inner finisher 15. Lumber support lever knob
16. Seat lifter lever 17. Seat lifter lever bracket 18. Seat cushion trim & pad
19. Seat cushion frame 20. Front leg cover (inner) 21. Front leg cover (outer)
22. Rear leg cover (inner) 23. Rear leg cover (outer)

SE-7
FRONT SEAT

Removal and Installation EIS004OQ

REMOVAL
CAUTION:
For vehicles equipped with side air bags, disconnect the battery negative terminal, and wait at least 3
minutes before beginning work.
1. Remove side air bag module connector (vehicles with side air bags) and seatbelt buckle switch harness
connector.
2. Remove front and rear leg covers.
3. Remove bolts (4), and remove seat from vehicle.
CAUTION:
When removing and installing, use shop cloths to protect
parts from damage and interference.

MIIB0034E

INSTALLATION
Install in the reverse order of removal.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage and interference.
Disassembly and Assembly of Seatback EIS004OR

SEATBACK TRIM PAD
SMA for VIN >SJN**AK12U1277776
Disassembly
1. Unfasten seatback fastener. (Vehicles with side air bags)
2. Remove retainer.

MIIB0035E

3. Turn over seatback trim, remove nuts (2), and remove fixed
inner cross rod. (Vehicles with side air bags)

MIIB0036E

SE-8
FRONT SEAT

4. Use pincers, etc., to push up hooks shown by the arrows in the
figure, and remove headrest holder from seatback. A
5. Remove seatback trim and pad from seatback frame.

MIIB0037E

D
Assembly
Install in the reverse order of removal.
CAUTION: E
Before installing headrest holder, check its orientation (front/rear and right/left).
SEATBACK FRAME
Disassembly F
1. Remove seatback trim&pad.
2. Pull out side air bag connector from back of seat cushion.
3. Remove lumber support lever knob, seat lifter lever, reclining dial, seat slide out finisher, slide inner cover, G
and seat slide inner finisher.
4. Remove seatback frame bolts and remove seatback frame from seat slide assembly.
H
Assembly
Install in the reverse order of removal.
CAUTION: SE
After assembling seatback frame, make sure reclining device operates.
Disassembly and Assembly of Seat Cushion EIS004OS

SEAT CUSHION TRIM PAD J
Disassembly
1. Remove seat lifter cover, seat lifter lever, reclining lever, seat slide out finisher, slide inner cover, and seat
slide inner finisher. K
2. Remove seatback frame bolts, and the remove seat cushion assembly from seatback frame
3. Remove retainer from the back of cushion.
4. Remove seat cushion trim&pad from seat cushion frame. L

MIIB0038E

Assembly
Install in the reverse order of removal.
CAUTION:
When assembling seat cushion assembly in seatback assembly, make sure the reclining device oper-
ates.
SEAT CUSHION FRAME
Disassembly
1. Remove short cushion trim&pad.
2. Remove bolts (4), and then remove seat cushion frame from seat slide assembly.

SE-9
FRONT SEAT

Assembly
Install in the reverse order of removal.

SE-10
REAR SEAT

REAR SEAT PFP:88300
A
Component Parts Location SMA for VIN >SJN**AK12U1133256
EIS004OT

BENCH SEAT
B

MIIB9067E
J
1. Rear seatback trim and pad 2. Seat cushion trim and pad 3. Seatback lock knob
4. Rear seat lock (RH) 5. Headrest 6. Headrest holder (free)
7. Headrest holder (locked) 8. Seatback frame 9. Rear seat lock (LH) K
10. Rear seat side bracket (LH) 11. Rear seat side bracket (RH)

SE-11
REAR SEAT

SPLIT SEAT

MIIB9068E

1. Rear seatback trim and pad (RH) 2. Headrest 3. Headrest holder (free)
4. Headrest holder (locked) 5. Rear seatback trim and pad (LH) 6. Seatback lock knob
7. Rear seat lock (RH) 8. Rear seatback frame (RH) 9. Rear seatback frame (LH)
10. Rear set cushion assembly 11. Rear seat lock (LH) 12. Rear seat side bracket (LH)
13. Rear center bracket (RH) 14. Rear seat side bracket (RH)

SE-12
REAR SEAT

SLIDE SEAT
A

MIIB9069E SE
1. Seat slide assembly 2. Slide rail 3. Rear seatback trim and pad
4. Seat cushion trim and pad
J
Removal and Installation EIS004OU

REMOVAL
Seat Cushion K
q Lift up seat cushion bottom, remove wire from plastic hooks (2
locations), and pull forward to remove.
L

MIIB0041E

Seatback (Bench Seat)
q Turn over rear seatback carpet, remove rear seat side bracket
bolts (2), and remove seatback from vehicle.

MIIB9070E

SE-13
REAR SEAT

seatback (Split Seat)
1. Turn over rear seatback carpet, remove side bracket bolts (2),
and remove seatback from vehicle.

MIIB9070E

2. Turn over rear seatback carpet, remove center bracket seatback
bolts (2), and remove.

MIIB0044E

Rear Seat Side Bracket
1. Remove seat cushion and rear seatback.
2. Remove bolts (1 at LH/RH each), and remove rear seat side
brackets (LH/RH) from vehicle.

MIIB9071E

Rear Seat Center Bracket
1. Remove rear seat cushion and rear seatback.
2. Remove bolts (two), and them remove rear seat center bracket
from vehicle.

MIIB0046E

Child Car Seat Anchor That Complies With ISO FIX
1. Remove seat cushion.

SE-14
REAR SEAT

2. Remove bolts (1 at LH/RH each), and them remove child car
seat anchors that complies with ISO FIX (LH/RH) from vehicle. A

MIIB0047E

D
INSTALLATION
Install in the reverse order of removal.
E

SE-15
REAR SEAT

REAR SEATBACK DISASSEMBLY AND ASSEMBLY
Disassembly
1. Use pincers, etc., to push up hooks shown by the arrows in the
figure, and remove headrest holder from seatback.

MIIB0037E

2. Remove retainer, and separate seatback trim&pad, and seat-
back frame.

MIIB0048E

Assembly
Install in the reverse order of removal.
CAUTION:
Before installing headrest holder, check its orientation (front/rear and right/left).

SE-16

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo