Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Micra 2003-2006 Approved 03k12e RAX
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download RAX documenatation <<
Text preview - extract from the document
REAR AXLE
D DRIVELINE/AXLE
A
B
SECTION
REAR AXLE C
RAX
E
CONTENTS
PRECAUTIONS ......................................................... 2 . Removal and Installation ......................................... 5
. F
Caution .................................................................... 2
. REMOVAL ............................................................ 5
.
Precautions for Brake System ................................. 2 . INSTALLATION .................................................... 6
.
PREPARATION .......................................................... 3. Disassembly and Assembly ..................................... 6 . G
Special Service Tools .............................................. 3 . DISASSEMBLY .................................................... 6
.
NOISE, VIBRATION AND HARSHNESS (NVH) INSPECTION AFTER DISASSEMBLY ................. 7 .
TROUBLESHOOTING ............................................... 4 . ASSEMBLY .......................................................... 7
.
H
NVH Troubleshooting Chart .................................... 4 . INSPECTION AFTER ASSEMBLY ....................... 7 .
WHEEL HUB ............................................................. 5
. SERVICE DATA AND SPECIFICATIONS (SDS) ....... 8 .
On-Vehicle Inspection ............................................. 5 . Wheel Bearing ......................................................... 8
.
REAR WHEEL BEARING .................................... 5 . Tightening Torque .................................................... 8
. I
J
K
L
M
RAX-1
PRECAUTIONS
PRECAUTIONS PFP:00001
Caution EDS00128
Observe the following precautions when disassembling and servicing drive shaft.
q Perform work in a location which is as dust-free and dirt-free as possible.
q Before disassembling and servicing, clean the outside of parts.
q The disassembly and service location must be clean. Care must be taken to prevent parts from becoming
dirty and to prevent the entry of foreign objects.
q Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a clean
cover must be placed over parts.
q Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint adher-
ing to parts.
q Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be removed by
blowing with air or wiping with paper shop cloths.
Precautions for Brake System EDS00129
q When installing rubber parts, final tightening must be carried out
under unladen condition* with tires on ground.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack, hand
tools and mats in designated positions.
q Use flare nut wrench when removing or installing brake tubes.
q After installing removed suspension parts, check wheel align-
ment and adjust if necessary.
q Always torque brake lines when installing.
SBR686C
RAX-2
PREPARATION
PREPARATION PFP:00002
A
Special Service Tools EDS0012A
Description Application
B
Drift
ST30720000
Installing hub cap C
a: 77 mm (3.03 in) dia.
b: 55 mm (2.17 in) dia.
ZZA0701D RAX
Drift E
ST33022000 q Installing wheel bearing
a: 56 mm (2.20 in) dia. q Installing ABS sensor rotor
b: 110 mm (4.33 in) dia.
F
ZZA0881D
G
Drift
ST33710000
Removing wheel bearing
a: 30 mm (1.18 in) dia.
b: 23 mm (0.91 in) dia. H
ZZA1234D
I
J
K
L
M
RAX-3
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING PFP:00003
NVH Troubleshooting Chart EDS0012B
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
Refer to RAX-5, "REAR WHEEL BEARING"
Refer to RAX-5, "REAR WHEEL BEARING"
NVH in FAX and FSU sections.
--
Reference page
NVH in FAX section.
NVH in WT section.
NVH in WT section.
NVH in BR section.
NVH in PS section.
FRONT AXLE AND FRONT SUSPENSION
Improper installation, looseness
Wheel bearing damage
Possible cause and SUSPECTED PARTS Parts interference
DRIVE SHAFT
ROAD WEEL
STEERING
BRAKES
TIRES
Noise ◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo