Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Micra 2003-2006 Approved 05k12e ACC
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download ACC documenatation <<
Text preview - extract from the document
ACCELERATOR CONTROL SYSTEM
B ENGINE
A
ACCELERATOR CONTROL SYSTEM
SECTION ACC ACC
C
D
E
CONTENTS
ACCELERATOR CONTROL SYSTEM ..................... 2 . SERVICE DATA AND SPECIFICATIONS (SDS) ....... 3 . F
Removal and Installation ......................................... 2
. Tightening Torque .................................................... 3
.
REMOVAL ............................................................ 2
.
INSTALLATION .................................................... 2
. G
INSPECTION AFTER INSTALLATION ................ 2 .
H
I
J
K
L
M
ACC-1
ACCELERATOR CONTROL SYSTEM
ACCELERATOR CONTROL SYSTEM PFP:18005
Removal and Installation EBS00OJF
PBIC1506E
Accelerator pedal stopper
1. Accelerator pedal assembly 2.
(Under floor carpet)
REMOVAL
1. Remove harness connector.
2. Remove mounting bolts, and remove accelerator assembly.
CAUTION:
q Do not disassemble accelerator pedal assembly and remove sensors.
q Handle them carefully without subjecting them to impacts such as dropping.
q Be careful not to get it wet.
3. Fold the floor carpet and remove accelerator pedal stopper.
q Remove pedal stopper by turning it counterclockwise with fingers.
INSTALLATION
Install in the reverse order of removal. be careful of the following:
q Insert locating pin into vehicle side to position accelerator pedal assembly. Install mounting bolt to acceler-
ator pedal assembly.
q Align the stud bolt on the floor with the thread hole to insert accelerator pedal stopper until it contacts the
face.
INSPECTION AFTER INSTALLATION
q Check that the accelerator pedal moves smoothly within the whole operation range.
q Check that the accelerator pedal securely returns to the original position.
q For the electrical inspection of the accelerator pedal assembly, refer to EC-405, "DTC P2138 APP SEN-
SOR" (CR WITH EURO-OBD), EC-721, "DTC P2138 APP SENSOR" (CR WITHOUT EURO-OBD) and
EC-1197, "DTC P2138 APP SENSOR" (HR WITH EURO-OBD), EC-1519, "DTC P2138 APP SENSOR"
(HR WITHOUT EURO-OBD) or "Interpretation", "DIESEL INJECTION" in EC section(K9K).
q When accelerator electrical connector is disconnected, perform EC-49, "Accelerator Pedal Released
Position Learning" (CR WITH EURO-OBD), EC-479, "Accelerator Pedal Released Position Learning"
(CR WITHOUT EURO-OBD) and EC-858, "Accelerator Pedal Released Position Learning" (HR WITH
EURO-OBD), EC-1283, "Accelerator Pedal Released Position Learning" (HR WITHOUT EURO-OBD).
ACC-2
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS) PFP:00030
A
Tightening Torque EBS00OJG
Unit: N◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo