Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Micra 2003-2006 Approved 05k12e SE

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download SE documenatation <<

Text preview - extract from the document

SEAT

I BODY

SECTION SE SEAT
B

E
CONTENTS
PRECAUTIONS ......................................................... 2. SEATBACK FRAME ........................................... 12 . F
Precautions for Supplemental Restraint System Disassembly and Assembly of Seat Cushion ........ 13 .
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SEAT CUSHION TRIM PAD ............................... 13 .
SIONER" ................................................................. 2
. SEAT CUSHION FRAME ................................... 14 . G
Precautions ............................................................. 2
. REAR SEAT ............................................................. 15
.
CLIP AND FASTENER .............................................. 3 . Component Parts Location .................................... 15 .
List of Table ............................................................. 3
. BENCH SEAT (3 DOOR AND 5 DOOR) ............ 15 .
H
HEATED SEAT .......................................................... 4
. SLIDE SEAT (3 DOOR AND 5 DOOR) .............. 16 .
Description .............................................................. 4
. BENCH SEAT (C+C) .......................................... 17 .
Wiring Diagram -- H/SEAT ..................................... 5 . Removal and Installation (3 Door and 5 Door) ...... 17 .
FRONT SEAT ............................................................. 9
. REMOVAL .......................................................... 17
. SE
Component Parts Location ...................................... 9 . INSTALLATION .................................................. 18
.
Removal and Installation ........................................11 . REAR SEATBACK DISASSEMBLY AND
REMOVAL ...........................................................11
. ASSEMBLY ........................................................ 19
. J
INSTALLATION ...................................................11 . Removal and Installation (C+C) ............................. 19 .
Disassembly and Assembly of Seatback ...............11 . REMOVAL .......................................................... 19
.
SEATBACK TRIM PAD .......................................11 . INSTALLATION .................................................. 19
.
K
REAR SEATBACK DISASSEMBLY AND
ASSEMBLY ........................................................ 20
.

SE-1
PRECAUTIONS

PRECAUTIONS PFP:00001

Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EIS004P3

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
q Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions EIS004P4

q When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which
may get in the way with cloth.
q When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.
q Keep removed parts protected with cloth.
q If a clip is deformed or damaged, replace it.
q If an unreusable part is removed, replace it with a new one.
q Tighten bolts and nuts firmly to the specified torque.
q After re-assembly has been completed, make sure each part functions correctly.
q Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
q Do not use any organic solvent, such as thinner or benzine.

SE-2
CLIP AND FASTENER

CLIP AND FASTENER PFP:76906
A
List of Table EIS004ON

MIIB0032E

SE-3
HEATED SEAT

HEATED SEAT PFP:87335

Description EIS004P5

q When handling seat, be extremely careful not to scratch heating unit.
q To replace heating unit, seat trim and pad should be separated.
q Do not use any organic solvent, such as thinner, benzene, alcohol, etc. to clean trims.

SBT314

SE-4
HEATED SEAT

Wiring Diagram -- H/SEAT EIS004P6

MIWA0294E

SE-5
HEATED SEAT

MKWA0836E

SE-6
HEATED SEAT

MIWA0575E

SE-7
HEATED SEAT

MIWA0576E

SE-8
FRONT SEAT

FRONT SEAT PFP:87000
A
Component Parts Location EIS004OP

CAUTION:
When removing and installing seats, use shop cloths to protect the parts from damage. B

SE-9
FRONT SEAT

MIIB9203E

1. Headrest 2. Headrest holder (free) 3. Headrest holder (locked)
4. Seatback trim & pad 5. Side air bag module 6. Fixed inner cross rod
7. Seatback frame 8. Lumbar assembly 9. Reclining dial

SE-10
FRONT SEAT

10. Seat slide outer finisher 11. Tilt lever assembly 12. Tilt cable
13. Seat slide assembly 14. Seat slide inner finisher 15. Lumber support lever knob A
16. Seat lifter lever 17. Seat lifter lever bracket 18. Seat cushion trim & pad
19. Seat cushion frame 20. Front leg cover (inner) 21. Front leg cover (outer)
22. Rear leg cover (inner) 23. Rear leg cover (outer) 24. Belt buckle assembly B
25. Cushion pan undercover 26. Underseat cover

Removal and Installation EIS004OQ C
REMOVAL
CAUTION:
For vehicles equipped with side air bags, disconnect the battery negative terminal, and wait at least 3 D
minutes before beginning work.
1. Remove side air bag module connector (vehicles with side air bags) and seatbelt buckle switch harness
connector.
E
2. Remove front and rear leg covers.
3. Remove bolts (4), and remove seat from vehicle.
CAUTION: F
When removing and installing, use shop cloths to protect
parts from damage and interference.
G

H
MIIB0034E

INSTALLATION
Install in the reverse order of removal. SE
CAUTION:
When removing and installing, use shop cloths to protect parts from damage and interference.
J
Disassembly and Assembly of Seatback EIS004OR

SEATBACK TRIM PAD
Disassembly (3 Door and 5 Door) K
1. Unfasten seatback fastener. (Vehicles with side air bags)
2. Remove retainer.
L

MIIB0035E

3. Turn over seatback trim, remove nuts (2), and remove fixed
inner cross rod. (Vehicles with side air bags)

MIIB9097E

SE-11
FRONT SEAT

4. Use pincers, etc., to push up hooks shown by the arrows in the
figure, and remove headrest holder from seatback.
5. Remove seatback trim and pad from seatback frame.

MIIB0037E

Disassembly (C+C)
1. Remove headrest.
2. Unfasten seatback fastener.
3. Separate both retainer parts, then release from seatback frame.
4. Turn over seatback trim, remove nuts (2), and remove fixed
inner cross rod.
5. Remove headrest holders, tilt lever knob, tilt lever escutcheon,
reclining dial.
6. Remove lumbar lever and seat lifter lever (driver seat).
7. Remove seat slide and outer finisher.
8. Pull air bag connector and heating connector out of seat slide MIIB9206E

frame.
9. Remove seatback trim and pad from seatback frame.
Assembly
Install in the reverse order of removal.
CAUTION:
Before installing headrest holder, check its orientation (front/rear and right/left).
SEATBACK FRAME
Disassembly (3 Door and 5 Door)
1. Remove seatback trim&pad.
2. Pull out side air bag connector from back of seat cushion.
3. Remove lumber support lever knob, seat lifter lever, reclining dial, seat slide out finisher, slide inner cover,
and seat slide inner finisher.
4. Remove seatback frame bolts and remove seatback frame from seat slide assembly.

SE-12
FRONT SEAT

Disassembly (C+C)
CAUTION: A
When removing or installing, use safety gloves to protect hands and seat cushion.
1. Remove seatback seat trim and pad. Refer to SE-11, "SEATBACK TRIM PAD" .
2. Remove side air bag module. Refer to SRS-42, "Removal and Installation" . B
3. Remove seat slide inner finisher.
4. Remove fixing lockwasher from reclining shaft, then remove
reclining shaft and pulley from seatback frame. C
5. Remove fixing bolts from seatback frame, then remove seatback
frame.
D
6. Remove active headrest protector, then remove fixing bolt and
active headrest (if equipped).
7. Remove fixing bolts from lumbar unit, then remove lumbar unit
assembly (driver seat). E

SE
MIIB9207E

Assembly
J
Install in the reverse order of removal.
CAUTION:
After assembling seatback frame, make sure reclining device operates.
K
Disassembly and Assembly of Seat Cushion EIS004OS

SEAT CUSHION TRIM PAD
Disassembly L
1. Remove seat lifter cover, seat lifter lever, reclining lever, seat slide out finisher, slide inner cover, and seat
slide inner finisher.
2. Remove seatback frame bolts, and the remove seat cushion assembly from seatback frame M
3. Remove retainer from the back of cushion.
4. Remove seat cushion trim&pad from seat cushion frame.

MIIB0038E

SE-13
FRONT SEAT

Assembly
Install in the reverse order of removal.
CAUTION:
When assembling seat cushion assembly in seatback assembly, make sure the reclining device oper-
ates.
SEAT CUSHION FRAME
Disassembly
1. Remove short cushion trim&pad.
2. Remove bolts (4), and then remove seat cushion frame from seat slide assembly.
Assembly
Install in the reverse order of removal.

SE-14
REAR SEAT

REAR SEAT PFP:88300
A
Component Parts Location EIS004OT

BENCH SEAT (3 DOOR AND 5 DOOR)
B

MIIB9098E
J
1. Rear seatback trim and pad 2. Seat cushion trim and pad 3. Seatback lock knob
4. Rear seat lock (RH) 5. Headrest 6. Headrest holder (free)
7. Headrest holder (locked) 8. Seatback frame 9. Rear seat lock (LH) K
10. Rear seat side bracket (LH) 11. Rear seat side bracket (RH)

SE-15
REAR SEAT

SLIDE SEAT (3 DOOR AND 5 DOOR)

MIIB9069E

1. Seat slide assembly 2. Slide rail 3. Rear seatback trim and pad
4. Seat cushion trim and pad

SE-16
REAR SEAT

BENCH SEAT (C+C)
A

MIIB9208E
SE
1. Rear seatback trim and pad 2. Seat cushion trim and pad 3. Bolt

Removal and Installation (3 Door and 5 Door) EIS004OU J
REMOVAL
Seat Cushion
q Lift up seat cushion bottom, remove wire from plastic hooks (2 K
locations), and pull forward to remove.

MIIB0041E

Seatback (Bench Seat)
q Turn over rear seatback carpet, remove rear seat side bracket
bolts (2), and remove seatback from vehicle.

MIIB9070E

SE-17
REAR SEAT

Rear Seat Side Bracket
1. Remove seat cushion and rear seatback.
2. Remove bolts (1 at LH/RH each), and remove rear seat side
brackets (LH/RH) from vehicle.

MIIB9119E

Rear Seat Center Bracket
1. Remove rear seat cushion and rear seatback.
2. Remove bolts (two), and them remove rear seat center bracket
from vehicle.

MIIB0046E

Child Car Seat Anchor That Complies With ISO FIX
1. Remove seat cushion.
2. Remove bolts (1 at LH/RH each), and them remove child car
seat anchors that complies with ISO FIX (LH/RH) from vehicle.

MIIB0047E

INSTALLATION
Install in the reverse order of removal.

SE-18
REAR SEAT

REAR SEATBACK DISASSEMBLY AND ASSEMBLY
Disassembly A
1. Use pincers, etc., to push up hooks shown by the arrows in the
figure, and remove headrest holder from seatback.
B

D
MIIB0037E

2. Remove retainer, and separate seatback trim&pad, and E
seatback frame.

MIIB0048E H
Assembly
Install in the reverse order of removal.
SE
CAUTION:
Before installing headrest holder, check its orientation (front/rear and right/left).
Removal and Installation (C+C) EIS00E6R J
REMOVAL
Seatback
1. Remove seat cushion. K
2. Remove fixing bolts (2), pull seatback lower end forward, then
slide downward and rotate forward.
L

MIIB9205E

INSTALLATION
Install in the reverse order of removal.

SE-19
REAR SEAT

REAR SEATBACK DISASSEMBLY AND ASSEMBLY
Disassembly
1. Use pliers to cut metal retainers from seatback trim and pad,
and seatback frame.

MIIB9211E

Assembly
Install in the reverse order of removal.

SE-20

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo