Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Altima 2006-2009 Approved TB Nissan Altima 2006 ex
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download ex documenatation <<
Text preview - extract from the document
B ENGINE
A
EX
SECTION
EXHAUST SYSTEM C
D
E
CONTENTS
PREPARATION .......................................................... 2
. Removal and Installation ......................................... 4
. F
Special Service Tool ................................................ 2
. Inspection After Installation ..................................... 5
.
Commercial Service Tools ....................................... 2
. EXHAUST SYSTEM (VQ35DE) ................................. 6 .
EXHAUST SYSTEM (QR25DE) ................................ 3 . Checking Exhaust System ....................................... 6
. G
Checking Exhaust System ...................................... 3. Removal and Installation ......................................... 7
.
Inspection After Installation ..................................... 8
.
H
I
J
K
L
M
Revision: July 2005 EX-1 2006 Altima
PREPARATION
PREPARATION PFP:00002
Special Service Tool EBS00J8J
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number Description
(Kent-Moore No.)
Tool name
KV10114400 Loosening or tightening heated oxygen sen-
(J-38365) sors:
Heated oxygen sensor wrench a: 22 mm (0.87 in)
S-NT636
Commercial Service Tools EBS00J8K
(Kent-Moore No.) Description
Tool name
(J-43897-18) Reconditioning the exhaust system threads
(J-43897-12) before installing a new oxygen sensor (Use
Oxygen sensor thread cleaner with anti-seize lubricant shown below):
a: J-43897-18 (18 mm dia.) for zirconia ox-
ygen sensor
b: J-43897-12 (12 mm dia.) for titania oxy-
gen sensor
AEM488
Anti-seize lubricant (Permatex 133AR Lubricating oxygen sensor thread cleaning
or equivalent meeting MIL specifica- tool when reconditioning exhaust system
tion MIL-A-907) threads
AEM489
Power tool Loosening nuts and bolts
PBIC0190E
Revision: July 2005 EX-2 2006 Altima
EXHAUST SYSTEM (QR25DE)
EXHAUST SYSTEM (QR25DE) PFP:20100
A
Checking Exhaust System EBS00J8L
Check the exhaust pipes, muffler, and mounting components for
incorrect attachment, leaks, cracks, damage, or deterioration. EX
C
D
SMA211A
E
F
G
H
I
J
K
L
M
Revision: July 2005 EX-3 2006 Altima
EXHAUST SYSTEM (QR25DE)
Removal and Installation EBS00J8M
WBIA0209E
1. Rear muffler 2. Rear muffler bracket (ground strap) 3. Center exhaust tube
4. Center exhaust tube hanger 5. Exhaust manifold 6. Front exhaust tube
7. Front exhaust tube spring 8. Front exhaust tube hanger 9. Seal bearing
10. Gasket
Revision: July 2005 EX-4 2006 Altima
EXHAUST SYSTEM (QR25DE)
CAUTION:
q Use genuine NISSAN exhaust system parts or equivalent, which are specifically designed for heat A
resistance, corrosion resistance, and shape.
q Perform the procedure with the exhaust system fully cooled down because the system will be hot
just after the engine is turned off. EX
q Be careful not to cut your hand on the insulator edges.
q If the insulator is badly deformed, repair or replace it. If deposits such as mud pile up on the insu-
lator, clean and inspect the insulator. C
q When installing the insulator avoid large gaps or interference between the insulator and each
exhaust pipe.
q Remove deposits from the sealing surface of each connection. Connect them securely to avoid D
exhaust gas leaks.
q Temporarily tighten the exhaust manifold side mounting nuts and the vehicle side mounting bolts.
Check each part for any interference, and then tighten the nuts and bolts to specification. E
q When installing each mounting rubber, avoid twisting or excessive extension in up/down and
right/left directions.
q Tighten the mounting bolts without causing interference with the flange. F
q Insert the seal bearing in the direction as shown. Tighten
the mounting bolt with the big end of the spring facing the
flange as shown.
G
H
I
WBIA0210E
Inspection After Installation EBS00J8N
J
q With the engine running, check the exhaust tube joints for exhaust gas leaks and abnormal noise.
q Check that the mounting brackets and mounting insulators are installed properly and free from excessive
stress. Improper installation could result in excessive noise, leaks, and vibration. K
L
M
Revision: July 2005 EX-5 2006 Altima
EXHAUST SYSTEM (VQ35DE)
EXHAUST SYSTEM (VQ35DE) PFP:20100
Checking Exhaust System EBS00J8O
Check the exhaust pipes, muffler, and mounting components for
incorrect attachment, leaks, cracks, damage, or deterioration.
SMA211A
Revision: July 2005 EX-6 2006 Altima
EXHAUST SYSTEM (VQ35DE)
Removal and Installation EBS00J8P
A
EX
C
D
E
F
G
H
I
J
K
L
M
WBIA0588E
1. RH rear muffler 2. LH rear muffler 3. RH rear muffler bracket with ground strap
4. LH rear muffler bracket 5. Center exhaust tube hanger 6. Center exhaust tube
7. Front exhaust tube 8. Front exhaust tube hanger 9. LH exhaust manifold
10. RH exhaust manifold 11. Gasket
Revision: July 2005 EX-7 2006 Altima
EXHAUST SYSTEM (VQ35DE)
CAUTION:
q Use genuine NISSAN exhaust system parts or equivalent, which are specifically designed for heat
resistance, corrosion resistance, and shape.
q Perform the procedures with the exhaust system fully cooled down because the system will be hot
just after the engine is turned off.
q Be careful not to cut your hand on the insulator edge.
q Always replace the exhaust gaskets with new ones for installation.
q If any insulator is badly deformed, repair or replace it. If deposits such as mud pile up on the insu-
lator, clean and inspect them.
q When installing the insulator avoid large gaps or interference between the insulator and the
exhaust pipe.
q Remove any deposits from the sealing surface of each connection. Connect them securely to
avoid exhaust gas leakage.
q Temporarily tighten the mounting nuts on the exhaust manifold side and the mounting bolts on the
vehicle side. Check each part for interference with other components, and then tighten the nuts
and bolts to specification.
q When installing each mounting rubber, avoid twisting or any over extension in up/down and right/
left directions.
Inspection After Installation EBS00J8Q
q With the engine running, check the exhaust tube joints for exhaust gas leaks and unusual noises.
q Check that the mounting brackets and mounting insulators are installed properly and free from excessive
stress. Improper installation could result in excessive noise, leaks, and vibration.
Revision: July 2005 EX-8 2006 Altima
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo