Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Armada 2004-2009 Approved Nissan Armada 2006 PG
<< Back |
HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download
Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing.
If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download PG documenatation <<Text preview - extract from the documentK ELECTRICAL
A
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS
SECTION PG B
C
D
E
CONTENTS
PRECAUTIONS ......................................................... 3 . Inspection with CONSULT-II (Self-Diagnosis) ....... 29 . F
Precautions for Supplemental Restraint System Removal and Installation of IPDM E/R .................. 30 .
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- REMOVAL .......................................................... 30
.
SIONER" ................................................................. 3
. INSTALLATION .................................................. 30 . G
POWER SUPPLY ROUTING CIRCUIT ..................... 4 . GROUND CIRCUIT .................................................. 31 .
Schematic ............................................................... 4
. Ground Distribution ................................................ 31
.
Wiring Diagram -- POWER -- ................................ 6 . MAIN HARNESS ................................................ 31 .
H
BATTERY POWER SUPPLY -- IGNITION SW. ENGINE ROOM HARNESS ............................... 34 .
IN ANY POSITION ............................................... 6 . ENGINE CONTROL HARNESS ......................... 37 .
ACCESSORY POWER SUPPLY -- IGNITION BODY HARNESS ............................................... 38 .
SW. IN ACC OR ON ............................................11 . BODY NO. 2 HARNESS .................................... 39 . I
IGNITION POWER SUPPLY -- IGNITION SW. BACK DOOR NO. 2 RH HARNESS ................... 40 .
IN ON ................................................................. 12
. HARNESS ................................................................ 41
.
IGNITION POWER SUPPLY -- IGNITION SW. Harness Layout ..................................................... 41
. J
IN ON AND/OR START ...................................... 13 . HOW TO READ HARNESS LAYOUT ................ 41 .
Fuse ...................................................................... 17
. OUTLINE ............................................................ 42
.
Fusible Link ........................................................... 17
. MAIN HARNESS ................................................ 43 .
PG
Circuit Breaker (Built Into BCM) ............................ 17 . ENGINE ROOM HARNESS (LH VIEW) ............. 45 .
IPDM E/R (INTELLIGENT POWER DISTRIBUTION ENGINE ROOM HARNESS (RH VIEW) ............ 48 .
MODULE ENGINE ROOM) ..................................... 18 . ENGINE CONTROL HARNESS ......................... 50 .
System Description ............................................... 18 . CHASSIS HARNESS ......................................... 52 . L
SYSTEMS CONTROLLED BY IPDM E/R .......... 18 . BODY HARNESS ............................................... 54 .
CAN COMMUNICATION LINE CONTROL ........ 18 . BODY NO. 2 HARNESS .................................... 56 .
IPDM E/R STATUS CONTROL .......................... 19 . ROOM LAMP HARNESS ................................... 58 . M
CAN Communication System Description ............. 19 . FRONT DOOR LH HARNESS ........................... 59 .
Function of Detecting Ignition Relay Malfunction ... 19 FRONT DOOR RH HARNESS ........................... 59 .
CONSULT-II Function IPDM E/R ........................... 20 . REAR DOOR LH HARNESS .............................. 60 .
CONSULT-II BASIC OPERATION ..................... 20 . REAR DOOR RH HARNESS ............................. 60 .
SELF-DIAGNOSTIC RESULTS ......................... 21 . BACK DOOR HARNESS ................................... 61 .
DATA MONITOR ................................................ 21 . Wiring Diagram Codes (Cell Codes) ..................... 62 .
ACTIVE TEST .................................................... 23 . ELECTRICAL UNITS LOCATION ........................... 65 .
Auto Active Test .................................................... 24. Electrical Units Location ........................................ 65 .
DESCRIPTION ................................................... 24 . ENGINE COMPARTMENT ................................. 65 .
OPERATION PROCEDURE .............................. 24 . PASSENGER COMPARTMENT ........................ 66 .
INSPECTION IN AUTO ACTIVE TEST MODE ... 24 HARNESS CONNECTOR ........................................ 68 .
Schematic ............................................................. 26
. Description ............................................................. 68
.
IPDM E/R Terminal Arrangement .......................... 27 . HARNESS CONNECTOR (TAB-LOCKING
IPDM E/R Power/Ground Circuit Inspection ......... 28 . TYPE) ................................................................. 68
.
HARNESS CONNECTOR (SLIDE-LOCKING
Revision: October 2006 PG-1 2006 Armada
TYPE) ................................................................. 69
. SUPER MULTIPLE JUNCTION (SMJ) .....................74 .
HARNESS CONNECTOR (DIRECT-CONNECT Terminal Arrangement ............................................74
.
SRS COMPONENT TYPE) ................................ 70 . FUSE BLOCK-JUNCTION BOX (J/B) .....................76 .
ELECTRICAL UNITS ............................................... 71 . Terminal Arrangement ............................................76
.
Terminal Arrangement ........................................... 71 . FUSE AND FUSIBLE LINK BOX .............................77 .
STANDARDIZED RELAY ......................................... 72 . Terminal Arrangement ............................................77
.
Description ............................................................. 72
. FUSE AND RELAY BOX ..........................................78.
NORMAL OPEN, NORMAL CLOSED AND Terminal Arrangement ............................................78
.
MIXED TYPE RELAYS ....................................... 72 .
TYPE OF STANDARDIZED RELAYS ................. 72 .
Revision: October 2006 PG-2 2006 Armada
PRECAUTIONS
PRECAUTIONS PFP:00011
A
Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EKS00B6C
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along B
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front C
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING: D
G To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer. E
G Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section. F
G Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
G
H
I
J
PG
L
M
Revision: October 2006 PG-3 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
POWER SUPPLY ROUTING CIRCUIT PFP:24110
Schematic EKS00B6E
For detailed ground distribution, refer to PG-31, "Ground Distribution" .
WKWA3853E
Revision: October 2006 PG-4 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
A
B
C
D
E
F
G
H
I
J
PG
L
M
WKWA5522E
Revision: October 2006 PG-5 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
Wiring Diagram -- POWER -- EKS00B6F
BATTERY POWER SUPPLY -- IGNITION SW. IN ANY POSITION
WKWA3855E
Revision: October 2006 PG-6 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
A
B
C
D
E
F
G
H
I
J
PG
L
M
WKWA3856E
Revision: October 2006 PG-7 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
WKWA3857E
Revision: October 2006 PG-8 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
A
B
C
D
E
F
G
H
I
J
PG
L
M
WKWA3858E
Revision: October 2006 PG-9 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
WKWA3859E
Revision: October 2006 PG-10 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
ACCESSORY POWER SUPPLY -- IGNITION SW. IN ACC OR ON
A
B
C
D
E
F
G
H
I
J
PG
L
M
WKWA3860E
Revision: October 2006 PG-11 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
IGNITION POWER SUPPLY -- IGNITION SW. IN ON
WKWA3861E
Revision: October 2006 PG-12 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
IGNITION POWER SUPPLY -- IGNITION SW. IN ON AND/OR START
A
B
C
D
E
F
G
H
I
J
PG
L
M
WKWA3862E
Revision: October 2006 PG-13 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
WKWA3863E
Revision: October 2006 PG-14 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
A
B
C
D
E
F
G
H
I
J
PG
L
M
WKWA3864E
Revision: October 2006 PG-15 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
WKWA3865E
Revision: October 2006 PG-16 2006 Armada
POWER SUPPLY ROUTING CIRCUIT
Fuse EKS00GMH
A
G If fuse is blown, be sure to eliminate cause of incident before
installing new fuse.
G Use fuse of specified rating. Never use fuse of more than speci-
fied rating. B
G Do not partially install fuse; always insert it into fuse holder prop-
erly.
C
G Remove fuse for "ELECTRICAL PARTS (BAT)" if vehicle is not
used for a long period of time.
D
CEL083
Fusible Link EKS00GMI
E
A melted fusible link can be detected either by visual inspection or by feeling with finger tip. If its condition is
questionable, use circuit tester or test lamp.
CAUTION:
G If fusible link should melt, it is possible that critical circuit (power supply or large current carrying F
circuit) is shorted. In such a case, carefully check and eliminate cause of incident.
G Never wrap outside of fusible link with vinyl tape.
G Never let fusible link touch any other wiring harness, vinyl or rubber parts. G
Circuit Breaker (Built Into BCM) EKS00GMJ
For example, when current is 30A, the circuit is broken within 8 to 20 H
seconds.
A circuit breaker is used for the following systems:
G Power windows I
G Power door locks
G Remote keyless entry system
G Power sunroof J
G Rear window wiper
SBF284E PG
L
M
Revision: October 2006 PG-17 2006 Armada
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PFP:284B7
System Description EKS00B6G
G IPDM E/R (Intelligent Power Distribution Module Engine Room) integrates the relay box and fuse block
which were originally placed in engine compartment. It controls integrated relays via IPDM E/R control cir-
cuits.
G IPDM E/R-integrated control circuits perform ON-OFF operation of relays, CAN communication control,
etc.
G It controls operation of each electrical component via ECM, BCM and CAN communication lines.
CAUTION:
None of the IPDM E/R integrated relays can be removed.
SYSTEMS CONTROLLED BY IPDM E/R
1. Lamp control
Using CAN communication lines, it receives signals from the BCM and controls the following lamps:
G Headlamps (Hi, Lo)
G Parking lamps
G Tail and license lamps
G Front fog lamps
2. Wiper control
Using CAN communication lines, it receives signals from the BCM and controls the front wipers.
3. Rear window defogger relay control
Using CAN communication lines, it receives signals from the BCM and controls the rear window defogger
relay.
4. A/C compressor control
Using CAN communication lines, it receives signals from the ECM and controls the A/C compressor
(magnetic clutch).
5. Starter control
Using CAN communication lines, it receives signals from the BCM and controls the starter relay.
6. Cooling fan control
Using CAN communication lines, it receives signals from the ECM and controls the cooling fan relays.
7. Horn control
Using CAN communication lines, it receives signals from the BCM and controls the horn relay.
CAN COMMUNICATION LINE CONTROL
With CAN communication, by connecting each control unit using two communication lines (CAN L-line, CAN
H-line), it is possible to transmit a maximum amount of information with minimum wiring. Each control unit can
transmit and receive data, and reads necessary information only.
1. Fail-safe control
G When CAN communication with other control units is impossible, IPDM E/R performs fail-safe control.
After CAN communication returns to normal operation, it also returns to normal control.
G Operation of control parts by IPDM E/R during fail-safe mode is as follows:
Controlled system Fail-safe mode
G With the ignition switch ON, the headlamp (low) is ON.
Headlamp
G With the ignition switch OFF, the headlamp (low) is OFF.
G With the ignition switch ON, the tail and parking lamps are ON.
Tail and parking lamps
G With the ignition switch OFF, the tail and parking lamps are OFF.
G With the ignition switch ON, the cooling fan HI operates.
Cooling fan
G With the ignition switch OFF, the cooling fan stops.
Until the ignition switch is turned off, the front wiper LO and HI remains in the same status it
Front wiper
was in just before fail-safe control was initiated.
Rear window defogger Rear window defogger relay OFF
Revision: October 2006 PG-18 2006 Armada
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
Controlled system Fail-safe mode
A
A/C compressor A/C compressor OFF
Front fog lamps Front fog lamp relay OFF
IPDM E/R STATUS CONTROL B
In order to save power, IPDM E/R switches status by itself based on each operating condition.
1. CAN communication status
G CAN communication is normally performed with other control units.
C
G Individual unit control by IPDM E/R is normally performed.
G When sleep request signal is received from BCM, mode is switched to sleep waiting status.
D
2. Sleep waiting status
G Process to stop CAN communication is activated.
G All systems controlled by IPDM E/R are stopped. When 1 second has elapsed after CAN communica- E
tion with other control units is stopped, mode switches to sleep status.
3. Sleep status
G IPDM E/R operates in low current-consumption mode. F
G CAN communication is stopped.
G When a change in CAN communication signal is detected, mode switches to CAN communication sta-
tus. G
G When a change in ignition switch signal is detected, mode switches to CAN communication status.
CAN Communication System Description EKS00B6H
H
Refer to LAN-25, "CAN COMMUNICATION" .
Function of Detecting Ignition Relay Malfunction EKS00B6I
I
G When the integrated ignition relay is stuck in a "closed contact" position and cannot be turned OFF, IPDM
E/R turns ON tail and parking lamps for 10 minutes to indicate IPDM E/R malfunction.
G When the state of the integrated ignition relay does not agree with the state of the ignition switch signal
J
received via CAN communication, the IPDM E/R activates the tail lamp relay.
Ignition switch signal Ignition relay status Tail lamp relay
ON ON -- PG
OFF OFF --
ON OFF --
L
OFF ON ON (10 minutes)
NOTE:
When the ignition switch is turned ON, the tail lamps are OFF. M
Revision: October 2006 PG-19 2006 Armada
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
CONSULT-II Function IPDM E/R EKS00B6J
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
IPDM E/R diagnostic Mode Description
SELF-DIAG RESULTS Displays IPDM E/R self-diagnosis results.
DATA MONITOR Displays IPDM E/R input/output data in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
CONSULT-II BASIC OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CON-
SULT-II CONVERTER to the data link connector, then turn igni-
tion switch ON.
BBIA0369E
2. Touch "START (NISSAN BASED VHCL)".
BCIA0029E
3. Touch "IPDM E/R" on "SELECT SYSTEM" screen.
G If "IPDM E/R" is not displayed refer to GI-39, "CONSULT-II Data Link Connector (DLC) Circuit" .
.
BCIA0030E
Revision: October 2006 PG-20 2006 Armada
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
4. Select the desired part to be diagnosed on the "SELECT DIAG
MODE" screen. A
B
C
BCIA0031E
D
SELF-DIAGNOSTIC RESULTS
Operation Procedure
1. Touch "SELF-DIAG RESULTS" on "SELECT DIAG MODE" E
screen.
2. Self-diagnosis results are displayed.
F
G
WKIA1264E
H
Display Item List
CONSULT-II TIME Possible causes
Display items Malfunction detection I
display code CRNT PAST
NO DTC IS
DETECTED. FUR-
THER TESTING -- -- -- -- -- J
MAY BE
REQUIRED.
G If CAN communication reception/transmis- Any of items listed PG
sion data has a malfunction, or if any of the below have errors:
control units fail, data reception/transmis-
CAN COMM CIRC U1000 X X G TRANSMIT DIAG
sion cannot be confirmed.
G ECM L
G When the data in CAN communication is
not received before the specified time. G BCM/SEC
NOTE: M
The details for display of the period are as follows:
G CRNT: Error currently detected with IPDM E/R.
G PAST: Error detected in the past and placed in IPDM E/R memory.
DATA MONITOR
Operation Procedure
1. Touch "DATA MONITOR" on "SELECT DIAG MODE" screen.
2. Touch "ALL SIGNALS", "MAIN SIGNALS" or "SELECTION FROM MENU" on the "DATA MONITOR"
screen.
ALL SIGNALS All signals will be monitored.
MAIN SIGNALS Monitors the predetermined item(s).
SELECTION FROM MENU Selects and monitors individual signal(s).
3. Touch "START".
Revision: October 2006 PG-21 2006 Armada
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
4. When "SELECTION FROM MENU" is selected, touch items to be monitored. When "ALL SIGNALS" is
selected, all the items will be monitored. When "MAIN SIGNALS" is selected, predetermined items are
monitored.
5. Touch "RECORD" while monitoring to record the status of the item being monitored. To stop recording,
touch "STOP".
Revision: October 2006 PG-22 2006 Armada
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
All Signals, Main Signals, Selection From Menu
Monitor item selection
A
CONSULT-II
Item name Display or unit ALL MAIN SELECTION Description
screen display
SIGNALS SIGNALS FROM MENU
B
MOTOR FAN
Motor fan request 1/2/3/4 X X X Signal status input from ECM
REQ
Compressor
AC COMP REQ ON/OFF X X X Signal status input from ECM C
request
Parking, license,
and tail lamp TAIL & CLR REQ ON/OFF X X X Signal status input from BCM
request D
Headlamp low
HL LO REQ ON/OFF X X X Signal status input from BCM
beam request
Headlamp high E
HL HI REQ ON/OFF X X X Signal status input from BCM
beam request
Front fog request FR FOG REQ ON/OFF X X X Signal status input from BCM
Front wiper STOP/1LOW/ F
FR WIP REQ X X X Signal status input from BCM
request LOW/HI
WIP AUTO
Wiper auto stop ACT P/STOP P X X X Output status of IPDM E/R
STOP G
Wiper protection WIP PROT OFF/Block X X X Control status of IPDM E/R
Starter request ST RLY REQ ON/OFF X X Status of input signal NOTE
H
Ignition relay Ignition relay status monitored
IGN RLY ON/OFF X X X
status with IPDM E/R
Rear defogger
RR DEF REQ ON/OFF X X X Signal status input from BCM I
request
Oil pressure Signal status input from IPDM
OIL P SW (*1) OPEN/CLOSE X X
switch E/R
J
Signal status input from IPDM
Hood switch HOOD SW (*1) OFF X
E/R
Theft warning
horn request
THFT HRN REQ ON/OFF X X Signal status input from BCM PG
Horn chirp HORN CHIRP ON/OFF X X Output status of IPDM E/R
Daytime running L
DTRL REQ ON/OFF X X Signal status input from BCM
lamp request
NOTE:
G Perform monitoring of IPDM E/R data with the ignition switch ON. When the ignition switch is in ACC posi- M
tion, display may not be correct.
G (*1) This item is displayed, but does not function.
ACTIVE TEST
Operation Procedure
1. Touch "ACTIVE TEST" on "SELECT DIAG-MODE" screen.
2. Touch item to be tested, and check operation.
3. Touch "START".
4. Touch "STOP" while testing to stop the operation.
Test name CONSULT-II screen display Description
With a certain ON-OFF operation, the rear defogger relay can be oper-
Rear defogger output REAR DEFOGGER
ated.
With a certain operation (OFF, HI ON, LO ON), the front wiper relay
Front wiper (HI, LO) output FRONT WIPER
(Lo, Hi) can be operated.
Cooling fan output MOTOR FAN With a certain operation (1, 2, 3, 4), the cooling fan can be operated.
Revision: October 2006 PG-23 2006 Armada
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
Test name CONSULT-II screen display Description
Lamp (HI, LO, TAIL, FOG) With a certain operation (OFF, HI ON, LO ON, TAIL ON, FOG ON), the
EXTERNAL LAMPS
output lamp relay (Low, High, Tail, Fog) can be operated.
Cornering lamp output CORNERING LAMP --
Horn output HORN With a certain ON-OFF operation, the horn relay can be operated.
Auto Active Test EKS00B6K
DESCRIPTION
G In auto active test mode, operation inspection can be performed when IPDM E/R sends a drive signal to
the following systems:
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo