Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Armada 2004-2009 Approved Nissan Armada 2007 WW
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download WW documenatation <<
Text preview - extract from the document
K ELECTRICAL
A
B
SECTION
WIPER, WASHER & HORN C
D
E
CONTENTS
PRECAUTION ........................................................... 3 . Cannot Be Adjusted ............................................... 23 . F
Precautions for Supplemental Restraint System Wipers Do Not Wipe When Front Washer Operates 23 ...
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Front Wipers Operate For 10 Seconds, Stop For 20
SIONER" ................................................................. 3
. Seconds, And After Repeating This Operation Five G
FRONT WIPER AND WASHER SYSTEM ................. 4 . Times, They Become Inoperative .......................... 23 .
Components Parts and Harness Connector Loca- Front Wiper Arms .................................................. 25 .
tion .......................................................................... 4
. REMOVAL AND INSTALLATION ....................... 25 .
H
System Description ................................................. 4 . FRONT WIPER ARM ADJUSTMENT ................ 25 .
LOW SPEED WIPER OPERATION ..................... 5 . Wiper Motor and Linkage ...................................... 26 .
HI SPEED WIPER OPERATION .......................... 5 . REMOVAL AND INSTALLATION ....................... 26 .
INTERMITTENT OPERATION ............................. 5 . REMOVAL .......................................................... 26 . I
AUTO STOP OPERATION ................................... 6 . INSTALLATION .................................................. 26 .
FRONT WASHER OPERATION .......................... 6 . Washer Nozzle Adjustment ................................... 26 .
MIST OPERATION ............................................... 6 . Washer Tube Layout ............................................. 27 . J
FAIL-SAFE FUNCTION ........................................ 6 . Wiper and Washer Switch ..................................... 27 .
COMBINATION SWITCH READING FUNCTION 7 ..... REMOVAL AND INSTALLATION ....................... 27 .
CAN Communication System Description ............... 7 . INSTALLATION .................................................. 27 . WW
Schematic ............................................................... 8
. Washer Fluid Reservoir ......................................... 27 .
Wiring Diagram -- WIPER -- ................................. 9 . REMOVAL AND INSTALLATION ....................... 27 .
Terminals and Reference Values for BCM ............ 12 . Washer Motor ........................................................ 28 .
Terminals and Reference Values for IPDM E/R .... 12 . REMOVAL AND INSTALLATION ....................... 28 . L
Work Flow ............................................................. 12. INSTALLATION .................................................. 28 .
Preliminary Inspection ........................................... 12 . REAR WIPER AND WASHER SYSTEM ................. 29 .
BCM POWER SUPPLY AND GROUND CIRCUIT Components Parts and Harness Connector Loca- M
CHECK ............................................................... 12
. tion ......................................................................... 29
.
CONSULT-II Function (BCM) ................................ 12 . System Description ................................................ 29 .
CONSULT-II START PROCEDURE ................... 12 . REAR WIPER OPERATION ............................... 30 .
WORK SUPPORT .............................................. 12 . INTERMITTENT OPERATION ........................... 30 .
DATA MONITOR ................................................ 12 . AUTO STOP OPERATION ................................. 31 .
ACTIVE TEST .................................................... 14 . REAR WASHER OPERATION ........................... 31 .
CONSULT-II Function (IPDM E/R) ........................ 14 . BCM WIPER SWITCH READING FUNCTION ... 32
CONSULT-II START PROCEDURE ................... 14 . Wiring Diagram -- WIP/ R -- ................................ 33 .
DATA MONITOR ................................................ 14 . Terminals and Reference Values for BCM ............. 35 .
ACTIVE TEST .................................................... 15 . How to Proceed With Trouble Diagnosis ............... 35 .
Front Wiper Does Not Operate ............................. 15 . Preliminary Check ................................................. 35 .
Front Wiper Stop Position Is Incorrect ................... 18 . INSPECTION FOR POWER SUPPLY AND
Only Front Wiper Low Does Not Operate ............. 19 . GROUND CIRCUIT ............................................ 35 .
Only Front Wiper High Does Not Operate ............. 21 . CONSULT-II Function (BCM) ................................ 35 .
Only Front Wiper Intermittent Does Not Operate ... 22 CONSULT-II START PROCEDURE ................... 35 .
Front Wiper Intermittent Operation Switch Position DATA MONITOR ................................................ 35 .
Revision: August 2006 WW-1 2007 Armada
ACTIVE TEST .................................................... 36
. Rear Wiper and Washer Switch .............................44 .
Rear Wiper Does Not Operate .............................. 36 . REMOVAL AND INSTALLATION ........................44 .
Rear Wiper Stop Position Is Incorrect .................... 39 . Washer Fluid Reservoir ..........................................45 .
Only Rear Wiper Does Not Operate ...................... 40 . REMOVAL AND INSTALLATION ........................45 .
Only Rear Wiper Intermittent Does Not Operate ... 40 Washer Motor .........................................................45 .
Wiper Does Not Wipe When Rear Washer Operates 41 ... REMOVAL AND INSTALLATION ........................45 .
Rear Wiper Arm ..................................................... 42
. POWER SOCKET ....................................................46 .
REMOVAL AND INSTALLATION ........................ 42 . Wiring Diagram -- P/SCKT -- ...............................46 .
Rear Wiper Motor .................................................. 43
. Power Socket LH and Rear Cargo Power Socket...47
REMOVAL AND INSTALLATION ........................ 43 . REMOVAL AND INSTALLATION ........................47 .
REMOVAL .......................................................... 43
. Front Power Socket RH and Console Power Socket ...47
INSTALLATION .................................................. 43
. REMOVAL AND INSTALLATION ........................47 .
Rear Washer Nozzle Adjustment ........................... 43 . HORN .......................................................................48
.
Rear Washer Tube Layout ..................................... 44 . Wiring Diagram -- HORN -- .................................48 .
Rear Washer Nozzle .............................................. 44
. Horn .......................................................................49
.
REMOVAL AND INSTALLATION ........................ 44 . REMOVAL AND INSTALLATION ........................49 .
Revision: August 2006 WW-2 2007 Armada
PRECAUTION
PRECAUTION PFP:00011
A
Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EKS00J1N
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along B
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front C
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING: D
q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer. E
q Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section. F
q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
G
H
I
J
WW
L
M
Revision: August 2006 WW-3 2007 Armada
FRONT WIPER AND WASHER SYSTEM
FRONT WIPER AND WASHER SYSTEM PFP:28810
Components Parts and Harness Connector Location EKS00J1O
WKIA4827E
1. IPDM E/R E121, E122, E124 2. Air cleaner case 3. Front and rear washer motor E105
4. Washer fluid reservoir 5. Front wiper motor E23 6. Combination switch M28
(view with cowl top removed)
7. BCM M18, M20
System Description EKS00J1P
q Both front wiper relays are located in the IPDM E/R (intelligent power distribution module engine room).
q The wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input ter-
minals. Terminal combination status is read by the BCM (body control module) when the wiper switch is
turned ON.
q BCM controls front wiper LO, HI, and INT (intermittent) operation.
q IPDM E/R operates the wiper motor according to CAN communication signals from the BCM.
Power is supplied at all times
q to ignition relay, located in the IPDM E/R, and
q through 50A fusible link (letter f , located in the fuse and fusible link box)
q to BCM terminal 70, and
q through 30A fuse (No. 39, located in the IPDM E/R)
q to front wiper relay (located in the IPDM E/R).
With the ignition switch in ON or START position, power is supplied
q to ignition relay, located in the IPDM E/R, and
q through 10A fuse (No. 9, located in the fuse block J/B)
q to combination switch terminal 14, and
q through 10A fuse (No. 59, located in the fuse and relay box)
q to BCM terminal 38.
Revision: August 2006 WW-4 2007 Armada
FRONT WIPER AND WASHER SYSTEM
Ground is supplied
q to BCM terminal 67 and A
q to combination switch terminal 12
q through grounds M57, M61 and M79, and
B
q to IPDM E/R terminals 38 and 59 and
q to front wiper motor terminal 1
q through grounds E9, E15 and E24. C
LOW SPEED WIPER OPERATION
When the ignition switch is in the ON or START position, and the front wiper switch is turned to the low posi-
tion, the BCM detects a low speed wiper ON request through the combination switch (wiper switch) reading D
function.
The BCM then sends a front wiper (low) request signal over CAN communication lines
q from BCM terminals 39 and 40 E
q to IPDM E/R terminals 39 and 40.
When IPDM E/R receives front wiper (low) request signal, it supplies ground to energize the front wiper relay.
With the front wiper relay energized, power is supplied F
q through front wiper relay
q to front wiper high relay
q through IPDM E/R terminal 32 G
q to front wiper motor terminal 3.
With power and ground supplied, the front wiper motor operates at low speed.
H
HI SPEED WIPER OPERATION
When the ignition switch is in the ON or START position, and the front wiper switch is turned to the high posi-
tion, the BCM detects a high speed wiper ON request through the combination switch (wiper switch) reading I
function.
The BCM then sends a front wiper (high) request signal over CAN communication lines
q from BCM terminals 39 and 40
J
q to IPDM E/R terminals 39 and 40.
When the IPDM E/R receives a front wiper (high) request signal, it supplies ground to energize the front wiper
and the front wiper high relays.
WW
With the front wiper and the front wiper high relays energized, power is supplied
q through front wiper relay
q to front wiper high relay L
q through IPDM E/R terminal 35
q to front wiper motor terminal 2.
With power and ground supplied, the front wiper motor operates at high speed. M
INTERMITTENT OPERATION
Wiper intermittent operation delay interval is determined from the combination of the intermittent wiper dial
position inputs and vehicle speed. During each intermittent operation delay interval, the BCM sends a front
wiper request signal to the IPDM E/R to operate the wipers.
When the ignition switch is in the ON or START position, and the front wiper switch is turned to an intermittent
position, the BCM detects a front wiper (intermittent) ON request through the combination switch (wiper
switch) reading function.
The BCM then sends a front wiper (intermittent) request signal over CAN communication lines
q from BCM terminals 39 and 40
q to IPDM E/R terminals 39 and 40.
When the BCM determines that combination switch status is front wiper intermittent ON, it performs the follow-
ing operations.
q BCM detects ON/OFF status of intermittent wiper dial position.
q BCM calculates operation interval from wiper dial position and vehicle speed signal received through CAN
communications.
Revision: August 2006 WW-5 2007 Armada
FRONT WIPER AND WASHER SYSTEM
q BCM sends front wiper request signal (INT) to IPDM E/R at calculated operation interval.
When the IPDM E/R receives a front wiper request signal (INT), it supplies ground to energize the front wiper
relay. It then sends an auto-stop signal to the BCM, and conducts intermittent front wiper motor operation.
AUTO STOP OPERATION
When the wiper arms are not located at the base of the windshield, and the wiper switch is turned OFF, the
wiper motor will continue to operate until the wiper arms reach the windshield base. When the wiper arms
reach the base of windshield, front wiper motor terminals 6 and 1 are connected.
Ground is supplied
q to IPDM E/R terminal 43
q through front wiper motor terminal 6
q through front wiper motor terminal 1
q through grounds E9, E15 and E24.
The IPDM E/R sends an auto stop operation signal to the BCM through CAN communication lines.
When the BCM receives an auto stop operation signal, the BCM sends wiper stop signal to the IPDM E/R over
CAN communication lines. The IPDM E/R then de-energizes the front wiper relay.
The wiper motor will then stop the wiper arms at the STOP position.
FRONT WASHER OPERATION
When the ignition switch is in the ON or START position, and the front and rear washer switches are OFF, the
front and rear washer motor is supplied power
q through 10A fuse (No. 9, located in the fuse block J/B)
q through combination switch (wiper switch) terminal 14
q through combination switch (wiper switch) terminal 13
q to front and rear washer motor terminal 1, and
q through combination switch (wiper switch) terminal 11
q to front and rear washer motor terminal 2.
When the front wiper switch is in the front washer position, the BCM detects a front washer signal request
through the combination switch (wiper switch) reading function.
Combination switch ground is supplied
q to front and rear washer motor terminal 2
q through combination switch (wiper switch) terminal 11
q through combination switch (wiper switch) terminal 12
q through grounds M57, M61 and M79.
With ground supplied, the front and rear washer motor is operated in the front direction.
When the BCM detects that front washer motor has operated for 0.4 seconds or longer, the BCM uses CAN
communication and sends a wiper request signal to the IPDM E/R for low speed operation of wipers.
When the BCM detects that the washer switch is OFF, low speed operation cycles approximately 3 times and
then stops.
MIST OPERATION
When the wiper switch is temporarily placed in the mist position, wiper low speed operation cycles once and
then stops.
For additional information about wiper operation under this condition, refer to WW-5, "LOW SPEED WIPER
OPERATION" .
If the switch is held in the mist position, low speed operation continues.
FAIL-SAFE FUNCTION
The BCM includes fail-safe function to prevent malfunction of electrical components controlled by CAN com-
munications if a malfunction in CAN communications occurs.
The BCM uses CAN communications to stop output of electrical components it controls.
Until the ignition switch is turned off, the front wiper system remains in same status as just before fail-safe con-
trol was initiated. (If wiper was in low speed operation just before fail-safe, it continues low speed operation
until ignition switch is turned OFF.)
When fail-safe status is initiated, the BCM remains in standby until normal signals are received.
When normal signals are received, fail-safe status is canceled.
Revision: August 2006 WW-6 2007 Armada
FRONT WIPER AND WASHER SYSTEM
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" . A
CAN Communication System Description EKS00J1Q
Refer to LAN-4, "SYSTEM DESCRIPTION" . B
C
D
E
F
G
H
I
J
WW
L
M
Revision: August 2006 WW-7 2007 Armada
FRONT WIPER AND WASHER SYSTEM
Schematic EKS00J1R
WKWA3814E
Revision: August 2006 WW-8 2007 Armada
FRONT WIPER AND WASHER SYSTEM
Wiring Diagram -- WIPER -- EKS00J1S
A
B
C
D
E
F
G
H
I
J
WW
L
M
WKWA3521E
Revision: August 2006 WW-9 2007 Armada
FRONT WIPER AND WASHER SYSTEM
WKWA3522E
Revision: August 2006 WW-10 2007 Armada
FRONT WIPER AND WASHER SYSTEM
A
B
C
D
E
F
G
H
I
J
WW
L
M
WKWA3523E
Revision: August 2006 WW-11 2007 Armada
FRONT WIPER AND WASHER SYSTEM
Terminals and Reference Values for BCM EKS00J1T
Refer to BCS-12, "Terminals and Reference Values for BCM" .
Terminals and Reference Values for IPDM E/R EKS00J1U
Refer to AV-30, "Terminals and Reference Value for Audio Unit for Base System" .
Work Flow EKS00J1V
1. Confirm the symptom or customer complaint.
2. Understand the system description, refer to WW-4, "System Description" .
3. Perform preliminary inspection, refer to WW-12, "Preliminary Inspection" .
4. Check symptom and repair or replace the cause of malfunction.
5. Does wiper function operate normally? If it operates normally, GO TO 6. If not, GO TO 4.
6. Inspection End.
Preliminary Inspection EKS00J1W
BCM POWER SUPPLY AND GROUND CIRCUIT CHECK
Refer to BCS-17, "BCM Power Supply and Ground Circuit Check" .
CONSULT-II Function (BCM) EKS00J1X
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
BCM diagnostic
Diagnostic mode Description
test item
Supports inspections and adjustments. Commands are transmitted to the BCM
WORK SUPPORT for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
Inspection by part
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER BCM part number can be read.
CONFIGURATION Performs BCM configuration read/write functions.
CONSULT-II START PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure" .
WORK SUPPORT
Work Support Setting Item
Item Description CONSULT-II
When wiper switch is at INTERMITTENT, front wiper intermittent
WIPER SPEED SETTING time can be selected according to vehicle speed. ON/OFF
q ON (Operated)/OFF (Not operated)
DATA MONITOR
Display Item List
Monitor item name
Contents
"OPERATION OR UNIT"
Displays "IGN Position (ON)/OFF, ACC Position (OFF)" status as judged from ignition
IGN ON SW "ON/OFF"
switch signal.
Displays "IGN switch ON (ON)/Other OFF or ACC (OFF)" status as judged from CAN
IGN SW CAN "ON/OFF"
communications.
FR WIPER HI "ON/OFF" Displays "Front Wiper HI (ON)/Other (OFF)" status as judged from wiper switch signal.
Revision: August 2006 WW-12 2007 Armada
FRONT WIPER AND WASHER SYSTEM
Monitor item name
Contents
"OPERATION OR UNIT" A
Displays "Front Wiper LOW (ON)/Other (OFF)" status as judged from wiper switch sig-
FR WIPER LOW "ON/OFF"
nal.
Displays "Front Wiper INT (ON)/Other (OFF)" status as judged from wiper switch sig- B
FR WIPER INT "ON/OFF"
nal.
Displays "Front Washer Switch (ON)/Other (OFF)" status as judged from wiper switch
FR WASHER SW "ON/OFF"
signal. C
Displays intermittent operation dial position setting (1 - 7) as judged from wiper switch
INT VOLUME (1 - 7)
signal.
FR WIPER STOP "ON/OFF" Displays "Stopped (ON)/Operating (OFF)" status as judged from the auto stop signal. D
VEHICLE SPEED "0.0 km/h" Displays vehicle speed as received from CAN communication.
E
F
G
H
I
J
WW
L
M
Revision: August 2006 WW-13 2007 Armada
FRONT WIPER AND WASHER SYSTEM
ACTIVE TEST
Display Item List
Display on CONSULT-II
Test item Description
screen
Front wiper HI output FR WIPER (HI) Front wiper HI can be operated by any ON-OFF operation.
Front wiper LO output FR WIPER (LO) Front wiper LO can be operated by any ON-OFF operation.
Front wiper INT output FR WIPER (INT) Front wiper INT can be operated by any ON-OFF operation.
CONSULT-II Function (IPDM E/R) EKS00J1Y
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
IPDM E/R diagnostic Mode Description
SELF-DIAG RESULTS Displays IPDM E/R self-diagnosis results.
DATA MONITOR Displays IPDM E/R input/output data in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
CONSULT-II START PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure" .
DATA MONITOR
All Items, Main Items, Select Item Menu
Monitor item selection
CONSULT-II
Item name Display or unit ALL MAIN SELECTION Description
screen display
SIGNALS SIGNALS FROM MENU
Front wiper
FR WIP REQ STOP/1LO/LO/HI x x x Signal status input from BCM.
request
Wiper auto stop WIP AUTO STOP ACT P/STOP P x x x Output status of IPDM E/R.
Wiper protection WIP PROT OFF/LS/HS/BLOCK x x x Control status of IPDM E/R.
NOTE:
Perform monitoring of IPDM E/R data with the ignition switch ON. When the ignition switch is at ACC, the dis-
play may not be correct.
Revision: August 2006 WW-14 2007 Armada
FRONT WIPER AND WASHER SYSTEM
ACTIVE TEST
Operation Procedure A
1. Touch "WIPER" on the "SELECT TEST ITEM" screen.
2. Touch "ACTIVE TEST" on the "SELECT DIAG MODE" screen.
B
3. Touch item(s) to be tested and check operation of the selected item(s).
4. During the operation check, touching "BACK" deactivates the operation.
Display Item List C
CONSULT-II
Test item Description
screen display
Front wiper (HI, LO) output FRONT WIPER With a certain operation (OFF, HI, LO) front wiper relays can be operated. D
Front Wiper Does Not Operate EKS00J1Z
CAUTION: E
During IPDM E/R fail-safe control, front wipers may not operate. Refer to PG-18, "CAN COMMUNICA-
TION LINE CONTROL" to make sure that it is not in fail-safe status.
1. CHECK IPDM E/R TO FRONT WIPERS F
With CONSULT-II
1. Select "IPDM E/R" with CONSULT-II, and select "ACTIVE G
TEST" on "SELECT DIAG MODE" screen.
2. Select "FRONT WIPER" on "SELECT TEST ITEM" screen.
Without CONSULT-II H
1. Turn on front wipers using auto active test. Refer to PG-22,
"Auto Active Test" .
2. Confirm front wiper operation. I
OK or NG
SKIA3486E
OK >> GO TO 4.
NG >> GO TO 2. J
WW
L
M
Revision: August 2006 WW-15 2007 Armada
FRONT WIPER AND WASHER SYSTEM
2. IPDM E/R TO FRONT WIPERS CIRCUIT INSPECTION
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connectors and front wiper motor connec-
tor.
3. Check continuity between IPDM E/R harness connector termi-
nals and front wiper motor harness connector terminals.
IPDM E/R Front wiper motor
Continuity
Connector Terminal Connector Terminal
32 3
E121
35 E23 2 Yes WKIA2827E
E122 43 6
4. Check continuity between IPDM E/R harness connector termi-
nals and ground.
IPDM E/R
Continuity
Connector Terminal
32
E121
35 Ground No
E122 43
WKIA1424E
5. Check continuity between IPDM E/R harness connector terminal
and ground.
IPDM E/R
Continuity
Connector Terminal
E122 38
Ground Yes
E124 59
WKIA1425E
6. Check continuity between front wiper motor harness connector
terminal 1 and ground.
Front wiper motor
Continuity
Connector Terminal
E23 1 Ground Yes
OK or NG
OK >> Connect connectors. GO TO 3.
NG >> Repair harness or connector.
WKIA2828E
Revision: August 2006 WW-16 2007 Armada
FRONT WIPER AND WASHER SYSTEM
3. IPDM E/R INSPECTION A
With CONSULT-II
1. Turn ignition switch ON.
B
2. Select "HI" on "ACTIVE TEST" screen.
3. When front wiper relay and front wiper high relay are operating, check voltage between IPDM E/R termi-
nals and ground.
C
Without CONSULT-II
1. Turn on front wipers using the auto active test. Refer to PG-22, "Auto Active Test" .
2. When front wiper relay, and front wiper high relay are operating, D
check voltage between IPDM E/R terminals and ground.
IPDM E/R
Voltage E
(+) (◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo