Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Primera 2000.2005 Approved Nissan Note 2006 IP

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download IP documenatation <<

Text preview - extract from the document

INSTRUMENT PANEL

I BODY

INSTRUMENT PANEL
SECTION IP B

E
CONTENTS
PRECAUTIONS ......................................................... 2 . MENT PAD ......................................................... 10
. F
Precautions for Supplemental Restraint System Disassembly and Assembly ................................... 11 .
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- GLOVE BOX ASSEMBLY ........................................ 12 .
SIONER" ................................................................. 2
. Removal And Installation ....................................... 12
. G
Precautions ............................................................. 2
. REMOVAL .......................................................... 12
.
CLIP AND FASTENER .............................................. 3 . INSTALLATION .................................................. 12
.
List of Table ............................................................. 3
. Disassembly And Assembly .................................. 12 .
H
INSTRUMENT PANEL ASSEMBLY .......................... 4 . DISASSEMBLY .................................................. 12
.
Component Parts Location ...................................... 4 . ASSEMBLY ........................................................ 12
.
Removal and Installation ......................................... 5 . CENTER CONSOLE ASSEMBLY ........................... 13 .
WORK ITEM TABLE ............................................ 5 . Removal And Installation ....................................... 13
. IP
REMOVAL ............................................................ 6
. REMOVAL .......................................................... 13
.
REMOVAL AND INSTALLATION OF INSTRU- INSTALLATION .................................................. 13
.
Disassembly And Assembly .................................. 13 . J

IP-1
PRECAUTIONS

PRECAUTIONS PFP:00001

Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" BIS000TY

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
q Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions BIS000TZ

q Disconnect both battery cables in advance.
q Disconnect air bag system line in advance.
q Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
q Be careful not to scratch pad and other parts.
q When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which
may get in the way with cloth.
q When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.
q Keep removed parts protected with cloth.
q If a clip is deformed or damaged, replace it.
q If an unreusable part is removed, replace it with a new one.
q Tighten bolts and nuts firmly to the specified torque.
q After re-assembly has been completed, make sure each part functions correctly.
q Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
q Do not use any organic solvent, such as thinner or benzine.

IP-2
CLIP AND FASTENER

CLIP AND FASTENER PFP:76906
A
List of Table BIS000U0

Symbol No. Shape Removal and installation
B

E
MIIB0017E

IP-3
INSTRUMENT PANEL ASSEMBLY

INSTRUMENT PANEL ASSEMBLY PFP:68200

Component Parts Location BIS000U1

MIIB9296E

IP-4
INSTRUMENT PANEL ASSEMBLY

1. Steering member 2. Upper instrument panel 3. Passenger air bag module*
4. Side ventilator grille (LH) 5. Instrument pad (driver side) 6. Instrument pad (passenger side)
A
7. Side ventilator grille (RH) 8. Instrument side mask (LH) 9. Instrument panel
10. Instrument side mask (RH) 11. Instrument panel stay (LHD only) 12. Instrument member bracket (RH)
B
13. Combination meter 14. Audio unit bracket (LH) 15. Audio unit (CD changer)
16. Audio unit bracket (RH) 17. Audio unit bracket (LH) 18. Deck pocket
19. Audio unit (CD) 20. Audio unit bracket (RH) 21. Switch panel finisher
C
22. Cluster lid A 23. Cluster lid C upper mask 24. Glove box cover assembly
25. Glove box lid 26. Fuse block lid 27. Cluster lid C (CD changer)
28. Cluster lid C (CD) 29. Steering column cover upper 30. Steering column protector
D
31. Steering column cover lower 32. Steering lock escutcheon 33. Central ventilator grille (LH)
34. Cluster lid C lower mask 35. Central ventilator grille (RH) 36. Air conditioner finisher
37. Instrument finisher lower 38. Instrument panel stay cover 39. Cup holder
E
40. Instrument panel stay finisher 41. Center console 42. Console mask
(LHD only)

*: Refer to SRS section.
F
: Insertion
: Pawl
: Plastic clip G
: Metal clip

Removal and Installation BIS000U2
H
WORK ITEM TABLE
Instrument
Instrument Upper
Instrument pad Combina- IP
Component Parts Location pad instrument Audio unit
panel (passenger tion meter
(driver side) panel
side)
A. Front pillar garnish IP-6 [1] [1] [1]
J
B. Upper instrument panel IP-6 [2] [2] [2]
C. Steering lock escutcheon IP-6 [3] [3]
D. Instrument finisher lower IP-6 [4] [4] K
E. Switch panel finisher IP-6 [5] [5]
F. Steering column cover upper IP-7 [6] [6] [1] [1]
L
G. Steering column cover lower IP-7 [7] [7] [2] [2]
H. Combination switch IP-7 [8] [8]
I. Cluster lid A IP-7 [9] [9] [3] [3] M
J. Combination meter IP-7 [ 10 ] [ 10 ] [4] [4]
K. Cluster lid C IP-8 [ 11 ] [ 11 ] [5] [1]
L. Air conditioner finisher IP-9 [ 12 ] [ 12 ] [6]
M. Instrument pad
IP-9 [ 13 ] [ 13 ] [7]
(driver side)
N. Center consol IP-9 [ 14 ] [ 14 ]
O. Instrument panel stay cover IP-9 [ 15 ] [ 15 ]
P. Glove box lid IP-9
Q. Glove box cover assembly IP-10 [ 16 ] [ 16 ]
R. Instrument side mask IP-10 [ 17 ] [ 17 ]
S. Steering wheel IP-10 [ 18 ] [ 18 ]
T. Instrument panel IP-10 [ 19 ] [ 19 ]
U. Instrument pad
IP-10 [ 20 ]
(passenger side)

IP-5
INSTRUMENT PANEL ASSEMBLY

[ ]: The number shows the removal order.
REMOVAL
A. Front Pillar Garnish
Refer to EI-26, "BODY SIDE TRIM" in EI section.
B. Upper Instrument Panel
1. Disconnect sunload sensor harness connector and remove the sunload sensor (if equipped). Refer to
ATC-116, "Removal and Installation" .
2. Lift up the upper instrument panel on one side to disengage
metal clips.
3. Remove the upper instrument panel.

MIIB9300E

C. Steering Lock Escutcheon
Pull to release steering lock escutcheon from the steering column cover.
CAUTION:
To install, align key cylinder end bottom protrusion with escutcheon inside notch and install.
D. Instrument Finisher Lower
Disengage upper plastic clips, and pull carefully rearward to remove
avoiding interference with surrounding surfaces.

MIIB9315E

E. Switch Panel Finisher
1. Remove fuse block lid.

MIIB9310E

IP-6
INSTRUMENT PANEL ASSEMBLY

2. Push the switch panel finisher to rear direction as shown.
3. Disconnect harness connectors and remove the switch panel A
finisher.

MIIB9301E

D
F. Steering Column Cover Upper
1. Tilt down the steering column, and remove screw (1) facing front of vehicle.
2. Disengage hooks and remove. E
CAUTION:
Pull out being careful of interference with surrounding objects.
G. Steering Column Cover Lower F
Remove screws (3), and pull downward to remove.
CAUTION:
Pull out being careful of interference with surrounding objects. G
H. Combination Switch
Refer to LT-112, "Removal and Installation" .
H
I. Cluster Lid A
Pull the cluster lid A to rearward direction and remove.
CAUTION: IP
Pull out being careful of interference with surrounding objects.

MIIB9302E

L
J. Combination Meter
1. Remove screw (1).
2. Pull rearward to disengage plastic clips as shown.
M
3. Disconnect harness connectors.
4. Lift up the lower side of combination meter to rotate the combi-
nation meter from the vertical to horizontal position.
5. Remove the combination meter from the instrument pad.

MIIB9303E

IP-7
INSTRUMENT PANEL ASSEMBLY

K. Cluster Lid C
1. Remove cluster lid C upper mask and remove upper fixing
screws.
2. Remove cluster lid C lower mask and remove lower fixing
screws.

MIIB9313E

3. Pull rearward to release the cluster lid from instrument panel
and pad.
4. Disconnect antenna connector and audio harness connector.

MIIB9314E

After removal:
q Separate the central ventilator grille LH and RH. Refer to ATC-130, "Removal and Installation" and MTC-
76, "Removal and Installation" .
q For (A) audio unit models, remove screws (4) securing audio
unit bracket LH and RH to release deck pocket and audio unit.
q For (B) audio unit models, remove screws (2) securing audio
unit bracket LH and RH to release audio unit.

MIIB9311E

IP-8
INSTRUMENT PANEL ASSEMBLY

L. Air Conditioner Finisher
Refer to ATC-112, "Removal and Installation of Controller" and A
MTC-62, "Removal and Installation" .

MIIB9308E
D

M. Instrument Pad (Driver Side)
Pull rearward to disengage metal clips from the instrument panel. E
CAUTION:
Pull out being careful of interference with surrounding objects.
After removal and if necessary, remove the side ventilator grille. Refer to ATC-130, "Removal and Installation"
F
and MTC-76, "Removal and Installation" .
N. Center Console
Refer to IP-13, "Removal And Installation" . G
O. Instrument Panel Stay Cover
1. Remove instrument panel stay finisher.
H

MIIB9305E
K
2. Remove mounting clips LH and RH.
3. Pull instrument stay cover to rearward to disengage plastic clips.
L
4. Disconnect power supply or cigar lighter harness connector if
equipped.
5. Remove instrument stay cover.
M
After removal, if necessary, remove screws securing the cup holder
to the instrument stay cover, and remove cup holder.

MIIB9304E

P. Glove Box Lid.
Refer to IP-12, "GLOVE BOX ASSEMBLY" .

IP-9
INSTRUMENT PANEL ASSEMBLY

Q. Glove Box Cover Assembly
1. Remove screws shown in the figure and remove the glove box
assembly.
2. After removal, separate parts if necessary. Refer to IP-12,
"GLOVE BOX ASSEMBLY" .

MIIB9307E

R. Instrument Side Mask
1. From inner side of instrument panel, push to disengage pawls
as shown.
2. Disconnect airbag cut-off switch from harness (passenger side
only).
3. Disengage airbag cut-off switch from instrument side mask (pas-
senger side only).
4. Pull out inserted area of instrument side mask and remove from
vehicle.

MIIB9306E

S. Steering Wheel
Refer to SRS-36, "DRIVER AIR BAG MODULE" and SRS-38, "SPIRAL CABLE" .
T. Instrument Panel
1. Remove the fuel filler lid opener. Refer to BL-212, "Removal and Installation of Fuel Filler Lid Opener" .
2. Tilt down steering column.
3. Remove screws, refer to IP-11, "Disassembly and Assembly" , and remove instrument panel and pad from
passenger door opening.
NOTE:
This operation requires two workers.
4. After removal, separate parts. Refer to IP-11, "Disassembly and Assembly" .
U. Instrument Pad (Passenger Side)
Remove mountings screws (3) securing the instrument pad to the instrument panel, and release metal clips
and remove the instrument pad (passenger side) from the Instrument panel. Refer to IP-11, "Disassembly and
Assembly" .
After removal and if necessary, remove the side ventilator grille. Refer to ATC-130, "Removal and Installation"
and MTC-76, "Removal and Installation" .

REMOVAL AND INSTALLATION OF INSTRUMENT PAD
Driver Side:
1. Remove the steering column upper cover. Refer to IP-7, "F. Steering Column Cover Upper" .
2. Remove the steering column lower cover. Refer to IP-7, "G. Steering Column Cover Lower" .
3. Remove the cluster lid A. Refer to IP-7, "I. Cluster Lid A" .
4. Remove the combination meter. Refer to IP-7, "J. Combination Meter" .
5. Remove the cluster lid C. Refer to IP-8, "K. Cluster Lid C" .
6. Remove the air conditioner finisher. Refer to IP-9, "L. Air Conditioner Finisher" .
7. Remove the instrument pad (driver side). Refer to IP-9, "M. Instrument Pad (Driver Side)" .
Passenger Side:
1. Remove the instrument panel assembly. Refer to IP-6, "REMOVAL" .

IP-10
INSTRUMENT PANEL ASSEMBLY

2. Remove the instrument pad (passenger side). Refer to IP-10, "U. Instrument Pad (Passenger Side)" .
A
Installation
Install in the reverse order of removal.
B
Disassembly and Assembly BIS000U3

MIIB9298E

1. Instrument pad (driver side) 2. Instrument pad (passenger side) 3. Instrument panel K
: Metal clip

IP-11
GLOVE BOX ASSEMBLY

GLOVE BOX ASSEMBLY PFP:68510

Removal And Installation BIS0014W

REMOVAL
1. Remove the glove box assembly. Refer to IP-10, "Q. Glove Box Cover Assembly" .
INSTALLATION
Install in the reverse order of removal.
Disassembly And Assembly BIS0014X

MIIB9297E

1. Spring assembly 2. Glove box cover 3. Glove box lid
4. Air conditioner inlet

DISASSEMBLY
1. Remove spring assembly screw.
2. Push glove box lid hooks to disengage glove box lid from the
glove box cover.
3. Remove the air conditioner inlet from the glove box cover.

MIIB9312E

ASSEMBLY
Assembly is in the reverse order of disassembly.

IP-12
CENTER CONSOLE ASSEMBLY

CENTER CONSOLE ASSEMBLY PFP:96910
A
Removal And Installation BIS0014U

REMOVAL
1. Remove shift knob from the shift lever (for manual transmission vehicles only). Refer to MT-12, "Removal
B
and Installation of Control Device and Cable" (JH3), MT-42, "Removal and Installation of Control Device
and Cable" (JR5).
2. Engage the shift knob in neutral position (for automatic transmission only).
C
3. Remove console mask. Refer to IP-13, "Disassembly And Assembly" .
4. Pull up parking brake lever, and remove finisher from the lever.
5. Remove the armrest (if equipped) from the driver seat (for manual transmission vehicles only). Refer to D
SE-7, "Component Parts Location" .
6. Remove power socket or cigar lighter from the center console and disconnect harness connector.
7. Slide front seat to access to the center console rear fixing E
screws.
8. Lift up the front side of the center console to disengage fixing
clips.
F
9. Disconnect all harness connectors.
10. Remove the center console.
G

MIIB9309E H
INSTALLATION
Install in the reverse order of removal.
IP
Disassembly And Assembly BIS0014V

MIIB9299E

1. Control lever finisher 2. Coin compartment 3. Console mask
4. Switch holder 5. Cup holder 6. Power socket
7. Power socket finisher 8. Center console

IP-13
CENTER CONSOLE ASSEMBLY

IP-14

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo