Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Primera 2000.2005 Approved Nissan Note 2006 SE

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download SE documenatation <<

Text preview - extract from the document

SEAT

I BODY

SECTION SE SEAT
B

E
CONTENTS
PRECAUTIONS ......................................................... 2. REMOVAL ............................................................ 8
. F
Precautions for Supplemental Restraint System INSTALLATION .................................................... 8
.
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Disassembly and Assembly of Seatback ................. 8 .
SIONER" ................................................................. 2
. SEATBACK TRIM PAD ......................................... 8 . G
Precautions ............................................................. 2
. SEATBACK FRAME ............................................. 9 .
CLIP AND FASTENER .............................................. 3 . Disassembly and Assembly of Seat Cushion ........ 10 .
List of Table ............................................................. 3
. SEAT CUSHION TRIM PAD ............................... 10 .
H
HEATED SEAT .......................................................... 4
. SEAT CUSHION FRAME ................................... 10 .
Description .............................................................. 4
. REAR SEAT ............................................................. 12
.
Wiring Diagram -- H/SEAT ..................................... 5 . Removal and Installation ....................................... 12.
FRONT SEAT ............................................................. 7
. REMOVAL .......................................................... 12
. SE
Component Parts Location ...................................... 7 . INSTALLATION .................................................. 12
.
Removal and Installation ......................................... 8 . Rear Seat Disassembly and Assembly ................. 13 .
J

SE-1
PRECAUTIONS

PRECAUTIONS PFP:00001

Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" BIS000U4

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
q Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions BIS000U5

q When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which
may get in the way with cloth.
q When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.
q Keep removed parts protected with cloth.
q If a clip is deformed or damaged, replace it.
q If an unreusable part is removed, replace it with a new one.
q Tighten bolts and nuts firmly to the specified torque.
q After re-assembly has been completed, make sure each part functions correctly.
q Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
q Do not use any organic solvent, such as thinner or benzine.

SE-2
CLIP AND FASTENER

CLIP AND FASTENER PFP:76906
A
List of Table BIS000U6

MIIB0032E

SE-3
HEATED SEAT

HEATED SEAT PFP:87335

Description BIS000U7

q When handling seat, be extremely careful not to scratch heating unit.
q To replace heating unit, seat trim and pad should be separated.
q Do not use any organic solvent, such as thinner, benzene, alcohol, etc. to clean trims.

SBT314

SE-4
HEATED SEAT

Wiring Diagram -- H/SEAT BIS000U8

MIWA0668E

SE-5
HEATED SEAT

MIWA0669E

SE-6
FRONT SEAT

FRONT SEAT PFP:87000
A
Component Parts Location BIS000U9

CAUTION:
When removing and installing seats, use shop cloths to protect the parts from damage. B

MIIB9345E

1. Headrest 2. Headrest holder (free) 3. Headrest holder (locked)
4. Seatback trim & pad 5. Side air bag module* 6. Fixed inner cross rod*
Seatback frame
7. Seatback frame (with active head rest) 8. 9. Armrest (driver only)
(without active head rest)
10. Seat slide outer finisher 11. Back table 12. Cushion pan undercover
13. Seat slide assembly 14. Seat slide inner finisher 15. Reclining inner finisher
16. Seat lifter lever 17. Reclining dial 18. Seat cushion trim & pad
19. Seat cushion frame 20. Front leg cover (inner) 21. Front leg cover (outer)
22. Rear leg cover (inner) 23. Rear leg cover (outer) 24. Belt buckle assembly**
*: Refer to SRS section (if equipped)
**: Refer to SB section
: Clip
: Always replace after every disassembly

SE-7
FRONT SEAT

: Sealing point

: Use recommended multi-purpose grease.
: Heated seat harness connector (if equipped)

Removal and Installation BIS000UA

REMOVAL
CAUTION:
Disconnect both battery cables, and wait at least 3 minutes before beginning work.
1. Remove side air bag module connector and seatbelt buckle switch harness connector and heated seat
connectors (if equipped).
2. Remove front and rear leg covers.
3. Remove bolts (4), and remove seat from vehicle.
4. Remove headrest.
CAUTION:
When removing and installing, use shop cloths to protect
parts from damage and interference.

MIIB0034E

INSTALLATION
q Install in the reverse order of removal.
q Tighten front seat mounting bolts to the torque.

: 46.6 N

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo