
PARKING BRAKE SYSTEM
F BRAKES
A
B
SECTION
PARKING BRAKE SYSTEM C
D
E
CONTENTS
NOISE, VIBRATION, AND HARSHNESS (NVH) Removal and Installation ......................................... 3 . PB
TROUBLESHOOTING ............................................... 2 . Inspection ................................................................ 3
.
NVH Troubleshooting Chart .................................... 2 . Adjustment ........................................................... .... 4
.
PARKING BRAKE CONTROL .................................. 3 . SERVICE DATA AND SPECIFICATIONS (SDS) ....... 5 . G
Components ............................................................ 3
. Parking Brake ...................................................... .... 5
.
H
I
J
K
L
M
PB-1
Symptom
X: Applicable
Reference page
Possible cause and
BRAKE
SUSPECTED PARTS
Noise
Shake
Shimmy, Judder
NVH Troubleshooting Chart
Pads - damaged Refer to BR section
X
Pads - uneven wear Refer to BR section.
X
Shims damaged Refer to BR section
X
Rotor imbalance Refer to BR section
X
X
PB-2
Rotor damage --
X
Rotor runout Refer to BR section
X
Rotor deformation --
X
Rotor deflection --
X
Rotor rust --
X
Rotor thickness variation Refer to BR section
X
DRIVE SHAFT Refer to FAX AND RAX section
X
X
AXLE Refer to FAX AND RAX section
X
X
X
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
SUSPENSION Refer to FSU AND RSU section
X
X
X
TIRES Refer to WT section
X
X
X
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
ROAD WHEEL Refer to WT section
X
X
X
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
STEERING Refer to PS section
X
X
X
PFP:00003
EFS001G9
PARKING BRAKE CONTROL
PARKING BRAKE CONTROL PFP:36010
A
Components EFS001GA
B
C
D
E
PB
SFIA0479E G
Removal and Installation EFS001GB
1. Remove center console. H
2. Disconnect warning lamp switch connector.
3. Remove cable mounting bolt. Loosen cable and remove self-
locking nut. I
4. Remove cable from toggle lever of disc brake.
J
SFIA0200E K
Inspection EFS001GC
q Operate parking brake lever with a force of 196 N (20 kg,44 lb). Check stroke is within specified number of L
notches. (Check it by hearing clicks of ratchet.)
Lever stroke : 7 - 8 notches
M
q Check parking lever assembly for bend, damage and cracks, and replace if necessary.
q Check cables and equalizer for wear and damage. If a malfunction is detected, replace applicable part.
q Check parking brake warning lamp switch. If a malfunction is detected, replace applicable part.
q Check each part for deformation, or damage by contact with other parts. If a malfunction is detected,
replace applicable part.
PB-3
PARKING BRAKE CONTROL
Adjustment EFS001GD
1. Insert a deep-well socket wrench into opening of parking brake
lever. Rotate self-locking nut to fully loosen cable. Return park-
ing brake lever and adjust rear brake shoe clearance.
SFIA0200E
2. Rotate road wheels to be sure that there is no drag.
3. After adjusting clearance of rear shoes, with no drag on rear
brake, adjust cable as follows:
a. Pull parking brake lever up so that a deep-well socket wrench
can be inserted.
b. Insert a deep-well socket wrench into opening of parking brake
lever. Rotate self-locking nut to adjust lever stroke.
CAUTION:
Do not reuse self-locking nut after removing it.
c. Operate parking brake lever 3 to 4 times with a force of 196 N MAA0182D
(20 kg,44 lb). Be sure lever stroke is within the specified number
of notches.
d. Return parking brake lever completely. Be sure there is no drag on rear brake.
PB-4
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS) PFP:00030
A
Parking Brake EFS001GG
Lever stroke [operating force 196 N (20 kg,44 lb)] 7 to 8 notches
Total stroke 18 notches B
Brake warning lamp stroke Within 1 notch
C
D
E
PB
G
H
I
J
K
L
M
PB-5
SERVICE DATA AND SPECIFICATIONS (SDS)
PB-6