Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Quest 2004-2009 Approved Nissan Quest 2004 PG
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download PG documenatation <<
Text preview - extract from the document
K ELECTRICAL
A
B
SECTION
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS C
D
E
CONTENTS
PRECAUTIONS ......................................................... 3 . GROUND CIRCUIT .................................................. 28 . F
Precautions for Supplemental Restraint System Ground Distribution ................................................ 28 .
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- MAIN HARNESS ................................................ 28 .
SIONER" ................................................................. 3
. ENGINE ROOM HARNESS ............................... 30 . G
Wiring Diagrams and Trouble Diagnosis ................. 3 . ENGINE CONTROL HARNESS ......................... 33 .
POWER SUPPLY ROUTING CIRCUIT ..................... 4 . BODY HARNESS ............................................... 34 .
Schematic ............................................................... 4
. BODY NO. 2 HARNESS .................................... 35 .
H
Wiring Diagram -- POWER -- ................................ 6 . BACK DOOR NO. 2 HARNESS ......................... 36 .
BATTERY POWER SUPPLY -- IGNITION SW. HARNESS ................................................................ 37
.
IN ANY POSITION ............................................... 6 . Harness Layout ..................................................... 37 .
ACCESSORY POWER SUPPLY -- IGNITION HOW TO READ HARNESS LAYOUT ................ 37 . I
SW. IN ACC OR ON ........................................... 10 . OUTLINE ............................................................ 38.
IGNITION POWER SUPPLY -- IGNITION SW. MAIN HARNESS ................................................ 39 .
IN ON ..................................................................11
. ENGINE ROOM HARNESS (LH VIEW) ............. 41 . J
IGNITION POWER SUPPLY -- IGNITION SW. ENGINE ROOM HARNESS (RH VIEW) ............ 44 .
IN ON AND/OR START ...................................... 12 . ENGINE CONTROL HARNESS ......................... 47 .
IPDM E/R (INTELLIGENT POWER DISTRIBUTION BODY HARNESS ............................................... 49 . PG
MODULE ENGINE ROOM) ..................................... 15 . BODY NO. 2 HARNESS .................................... 51 .
System Description ............................................... 15 . ROOM LAMP HARNESS ................................... 53 .
SYSTEMS CONTROLLED BY IPDM E/R .......... 15 . FRONT DOOR LH HARNESS ........................... 54 .
CAN COMMUNICATION LINE CONTROL ........ 15 . FRONT DOOR RH HARNESS ........................... 54 . L
IPDM E/R STATUS CONTROL .......................... 16 . SLIDING DOOR LH HARNESS ......................... 55 .
CAN Communication System Description ............. 16 . SLIDING DOOR RH HARNESS ......................... 55 .
Function of Detecting Ignition Relay Malfunction ... 16 BACK DOOR HARNESS ................................... 56 . M
CONSULT-II Function (IPDM E/R) ........................ 17 . Wiring Diagram Codes (Cell Codes) ..................... 57 .
CONSULT-II BASIC OPERATION ..................... 17 . ELECTRICAL UNITS LOCATION ........................... 60 .
SELF-DIAGNOSTIC RESULTS ......................... 18 . Electrical Units Location ........................................ 60 .
DATA MONITOR ................................................ 18 . ENGINE COMPARTMENT ................................. 60 .
ACTIVE TEST .................................................... 20 . PASSENGER COMPARTMENT ........................ 61 .
Auto Active Test .................................................... 21
. Fuse ....................................................................... 63
.
DESCRIPTION ................................................... 21 . Fusible Link ........................................................... 63
.
OPERATION PROCEDURE .............................. 21 . Circuit Breaker (Built Into BCM) ............................ 63 .
INSPECTION IN AUTO ACTIVE TEST MODE ... 21 HARNESS CONNECTOR ........................................ 64 .
Schematic ............................................................. 23
. Description ............................................................. 64
.
IPDM E/R Terminal Arrangement .......................... 24 . HARNESS CONNECTOR (TAB-LOCKING
IPDM E/R Power/Ground Circuit Inspection ......... 25 . TYPE) ................................................................. 64
.
Inspection with CONSULT-II (Self-Diagnosis) ....... 26 . HARNESS CONNECTOR (SLIDE-LOCKING
Removal and Installation of IPDM E/R .................. 27 . TYPE) ................................................................. 65
.
REMOVAL .......................................................... 27
. HARNESS CONNECTOR (DIRECT-CONNECT
INSTALLATION .................................................. 27 . SRS COMPONENT TYPE) ................................ 66 .
Revision: January 2005 PG-1 2004 Quest
ELECTRICAL UNITS ............................................... 67 . SUPER MULTIPLE JUNCTION (SMJ) .....................70 .
Terminal Arrangement ........................................... 67 . Terminal Arrangement ............................................70
.
STANDARDIZED RELAY ......................................... 68 . FUSE BLOCK-JUNCTION BOX(J/B) ......................71 .
Description ............................................................. 68
. Terminal Arrangement ............................................71
.
NORMAL OPEN, NORMAL CLOSED AND FUSE AND FUSIBLE LINK BOX .............................72 .
MIXED TYPE RELAYS ....................................... 68 . Terminal Arrangement ............................................72
.
TYPE OF STANDARDIZED RELAYS ................. 68 .
Revision: January 2005 PG-2 2004 Quest
PRECAUTIONS
PRECAUTIONS PFP:00011
A
Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EKS006F6
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along B
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front C
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING: D
q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer. E
q Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section. F
q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
G
Wiring Diagrams and Trouble Diagnosis EKS006F8
When you read wiring diagrams, refer to the following:
H
q Refer to GI-12, "How to Read Wiring Diagrams" in GI section.
q Refer to PG-4, "POWER SUPPLY ROUTING CIRCUIT" for power distribution.
When you perform trouble diagnosis, refer to the following: I
q Refer to GI-10, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES" in GI section.
q Refer to GI-25, "How to Perform Efficient Diagnosis for an Electrical Incident" in GI section.
J
PG
L
M
Revision: January 2005 PG-3 2004 Quest
POWER SUPPLY ROUTING CIRCUIT
POWER SUPPLY ROUTING CIRCUIT PFP:24110
Schematic EKS0064B
For detailed ground distribution, refer to PG-28, "Ground Distribution" .
WKWA2823E
Revision: January 2005 PG-4 2004 Quest
POWER SUPPLY ROUTING CIRCUIT
A
B
C
D
E
F
G
H
I
J
PG
L
M
WKWA2824E
Revision: January 2005 PG-5 2004 Quest
POWER SUPPLY ROUTING CIRCUIT
Wiring Diagram -- POWER -- EKS0064C
BATTERY POWER SUPPLY -- IGNITION SW. IN ANY POSITION
WKWA1704E
Revision: January 2005 PG-6 2004 Quest
POWER SUPPLY ROUTING CIRCUIT
A
B
C
D
E
F
G
H
I
J
PG
L
M
WKWA1705E
Revision: January 2005 PG-7 2004 Quest
POWER SUPPLY ROUTING CIRCUIT
WKWA2825E
Revision: January 2005 PG-8 2004 Quest
POWER SUPPLY ROUTING CIRCUIT
A
B
C
D
E
F
G
H
I
J
PG
L
M
WKWA1707E
Revision: January 2005 PG-9 2004 Quest
POWER SUPPLY ROUTING CIRCUIT
ACCESSORY POWER SUPPLY -- IGNITION SW. IN ACC OR ON
WKWA1708E
Revision: January 2005 PG-10 2004 Quest
POWER SUPPLY ROUTING CIRCUIT
IGNITION POWER SUPPLY -- IGNITION SW. IN ON
A
B
C
D
E
F
G
H
I
J
PG
L
M
WKWA1709E
Revision: January 2005 PG-11 2004 Quest
POWER SUPPLY ROUTING CIRCUIT
IGNITION POWER SUPPLY -- IGNITION SW. IN ON AND/OR START
WKWA1710E
Revision: January 2005 PG-12 2004 Quest
POWER SUPPLY ROUTING CIRCUIT
A
B
C
D
E
F
G
H
I
J
PG
L
M
WKWA1711E
Revision: January 2005 PG-13 2004 Quest
POWER SUPPLY ROUTING CIRCUIT
WKWA1712E
Revision: January 2005 PG-14 2004 Quest
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PFP:284B7 A
System Description EKS0064D
q IPDM E/R (Intelligent Power Distribution Module Engine Room) integrates the relay box and fuse block
B
which were originally placed in engine compartment. It controls integrated relays via IPDM E/R control cir-
cuits.
q IPDM E/R-integrated control circuits perform ON-OFF operation of relays, CAN communication control, oil
pressure switch signal reception, etc. C
q It controls operation of each electrical component via ECM, BCM and CAN communication lines.
CAUTION:
None of the IPDM E/R integrated relays can be removed. D
SYSTEMS CONTROLLED BY IPDM E/R
1. Lamp control E
Using CAN communication lines, it receives signals from the BCM and controls the following lamps:
q Headlamps (Hi, Lo)
q Parking lamps F
q Tail lamps
q Cornering lamps
q Front fog lamps G
2. Wiper control
Using CAN communication lines, it receives signals from the BCM and controls the front wipers.
3. Rear window defogger relay control H
Using CAN communication lines, it receives signals from the BCM and controls the rear window defogger
relay.
4. A/C compressor control I
Using CAN communication lines, it receives signals from the ECM and controls the A/C compressor
(magnetic clutch).
5. Cooling fan control J
Using CAN communication lines, it receives signals from the ECM and controls the cooling fan relays.
6. Horn control
Using CAN communication lines, it receives signals from the BCM and controls the horn relay. PG
CAN COMMUNICATION LINE CONTROL
With CAN communication, by connecting each control unit using two communication lines (CAN L-line, CAN
H-line), it is possible to transmit a maximum amount of information with minimum wiring. Each control unit can L
transmit and receive data, and reads necessary information only.
1. Fail-safe control
q When CAN communication with other control units is impossible, IPDM E/R performs fail-safe control. M
After CAN communication returns to normal operation, it also returns to normal control.
q Operation of control parts by IPDM E/R during fail-safe mode is as follows:
Controlled system Fail-safe mode
q With the ignition switch ON, the headlamp (low) is ON.
Headlamp
q With the ignition switch OFF, the headlamp (low) is OFF.
Tail and parking lamps q With the ignition switch ON, the tail and parking lamps are ON.
q With the ignition switch OFF, the tail and parking lamps are OFF.
q With the ignition switch ON, the cooling fan HI operates.
Cooling fan
q With the ignition switch OFF, the cooling fan stops.
Until the ignition switch is turned off, the front wiper LO and HI remains in the same status it
Front wiper
was in just before fail-safe control was initiated.
Rear window defogger Rear window defogger relay OFF
A/C compressor A/C compressor OFF
Front fog lamps Front fog lamp relay OFF
Revision: January 2005 PG-15 2004 Quest
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
IPDM E/R STATUS CONTROL
In order to save power, IPDM E/R switches status by itself based on each operating condition.
1. CAN communication status
q CAN communication is normally performed with other control units.
q Individual unit control by IPDM E/R is normally performed.
q When sleep request signal is received from BCM, mode is switched to sleep waiting status.
2. Sleep waiting status
q Process to stop CAN communication is activated.
q All systems controlled by IPDM E/R are stopped. When 1 second has elapsed after CAN communica-
tion with other control units is stopped, mode switches to sleep status.
3. Sleep status
q IPDM E/R operates in low current-consumption mode.
q CAN communication is stopped.
q When a change in CAN communication signal is detected, mode switches to CAN communication sta-
tus.
q When a change in ignition switch signal is detected, mode switches to CAN communication status.
CAN Communication System Description EKS006IC
Refer to LAN-6, "CAN COMMUNICATION" .
Function of Detecting Ignition Relay Malfunction EKS0064E
q When the integrated ignition relay is stuck in a "closed contact" position and cannot be turned OFF, IPDM
E/R turns ON tail and parking lamps for 10 minutes to indicate IPDM E/R malfunction.
q When the state of the integrated ignition relay does not agree with the state of the ignition switch signal
received via CAN communication, the IPDM E/R activates the tail lamp relay.
Ignition switch signal Ignition relay status Tail lamp relay
ON ON --
OFF OFF --
ON OFF --
OFF ON ON (10 minutes)
NOTE:
When the ignition switch is turned ON, the tail lamps are OFF.
Revision: January 2005 PG-16 2004 Quest
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
CONSULT-II Function (IPDM E/R) EKS0064F
A
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
Inspection Item, Diagnosis Mode Description
SELF-DIAG RESULTS The IPDM E/R performs diagnosis of CAN communication and self-diagnosis. B
DATA MONITOR The input/output data of the IPDM E/R is displayed in real time.
ACTIVE TEST The IPDM E/R sends a drive signal to electronic components to check their operation.
C
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
CONSULT-II BASIC OPERATION
D
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CON- E
SULT-II CONVERTER to the data link connector, then turn igni-
tion switch ON.
F
G
H
BBIA0336E
2. Touch "START (NISSAN BASED VHCL)".
I
J
PG
BCIA0029E
L
3. Touch "IPDM E/R" on "SELECT SYSTEM" screen.
q If "IPDM E/R" is not displayed, print "SELECT SYSTEM"
screen, then refer to LAN-3, "Precautions for CAN System" . M
BCIA0030E
Revision: January 2005 PG-17 2004 Quest
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
4. Select the desired part to be diagnosed on the "SELECT DIAG
MODE" screen.
BCIA0031E
SELF-DIAGNOSTIC RESULTS
Operation Procedure
1. Touch "SELF-DIAG RESULTS" on "SELECT DIAG MODE"
screen.
2. Self-diagnosis results are displayed.
WKIA1264E
Display Item List
TIME Possible
CONSULT-II
Display items Malfunction detection causes
display code CRNT PAST
NO DTC IS DETECTED.
FURTHER TESTING -- -- -- -- --
MAY BE REQUIRED.
Any of items
q If CAN communication reception/transmission listed below
data has a malfunction, or if any of the control have errors:
units fail, data reception/transmission cannot be
CAN COMM CIRC U1000 X X q TRANSMIT
confirmed.
DIAG
q When the data in CAN communication is not
q ECM
received before the specified time.
q BCM/SEC
NOTE:
The details for display of the period are as follows:
q CRNT: Error currently detected with IPDM E/R.
q PAST: Error detected in the past and placed in IPDM E/R memory.
DATA MONITOR
Operation Procedure
1. Touch "DATA MONITOR" on "SELECT DIAG MODE" screen.
2. Touch "ALL SIGNALS", "MAIN SIGNALS" or "SELECT FROM MENU" on the "DATA MONITOR" screen.
ALL SIGNALS All signals will be monitored.
MAIN SIGNALS Monitors the predetermined item(s).
SELECT FROM MENU Selects and monitors individual signal(s).
3. Touch "START".
4. Touch the required monitoring item on "SELECT ITEM MENU".
Revision: January 2005 PG-18 2004 Quest
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
5. Touch "RECORD" while monitoring to record the status of the item being monitored. To stop recording,
touch "STOP". A
B
C
D
E
F
G
H
I
J
PG
L
M
Revision: January 2005 PG-19 2004 Quest
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
All Signals, Main Signals, Select From Menu
CONSULT-II Monitor item selection
Item name screen display Display or unit ALL MAIN SELECT Description
SIGNALS SIGNALS FROM MENU
MOTOR FAN
Motor fan request 1/2/3/4 X X X Signal status input from ECM
REQ
Compressor
AC COMP REQ ON/OFF X X X Signal status input from ECM
request
Tail & clear
TAIL & CLR REQ ON/OFF X X X Signal status input from BCM
request
H/L LO request HL LO REQ ON/OFF X X X Signal status input from BCM
H/L HI request HL HI REQ ON/OFF X X X Signal status input from BCM
FR fog request FR FOG REQ ON/OFF X X X Signal status input from BCM
FR wiper request FR WIP REQ STOP/1LO/LO/HI X X X Signal status input from BCM
WIP AUTO
Wiper auto stop ACT P/STOP P X X X Output status of IPDM E/R
STOP
Wiper protection WIP PROT OFF/LS/HS/Block X X X Control status of IPDM E/R
Starter request ST RLY REQ ON/OFF X X Status of input signal NOTE
Ignition relay Ignition relay status monitored
IGN RLY ON/OFF X X X
status with IPDM E/R
Rear defogger
RR DEF REQ ON/OFF X X X Signal status input from BCM
request
Oil pressure Signal status input from IPDM
OIL P SW OPEN/CLOSE X X
switch E/R
Signal status input from IPDM
Hood switch HOOD SW OFF X
E/R (function is not enabled)
Theft warning
THFT HRN REQ ON/OFF X X Signal status input from BCM
horn request
Horn chirp HORN CHIRP ON/OFF X X Output status of IPDM E/R
Cornering lamp CRNRNG LMP
OFF/LEFT/RIGHT X X Signal status input from BCM
request REQ
NOTE:
Perform monitoring of IPDM E/R data with the ignition switch ON. When the ignition switch is in ACC position,
display may not be correct.
ACTIVE TEST
Operation Procedure
1. Touch "ACTIVE TEST" on "SELECT DIAG-MODE" screen.
2. Touch item to be tested, and check operation.
3. Touch "START".
4. Touch "STOP" while testing to stop the operation.
Test name CONSULT-II screen display Description
Tail lamp output TAIL LAMP With a certain ON-OFF operation, the tail lamp relay can be operated.
With a certain ON-OFF operation, the rear defogger relay can be oper-
Rear defogger output REAR DEFOGGER
ated.
With a certain operation (OFF, HI ON, LO ON), the front wiper relay
Front wiper (HI, LO) output FRONT WIPER
(Lo, Hi) can be operated.
Cooling fan output MOTOR FAN With a certain operation (1, 2, 3, 4), the cooling fan can be operated.
With a certain operation (OFF, HI ON, LO ON, FOG ON), the lamp
Lamp (HI, LO, FOG) output LAMPS
relay (Lo, Hi, Fog) can be operated.
Revision: January 2005 PG-20 2004 Quest
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
Test name CONSULT-II screen display Description
A
Cornering lamp output CORNERING LAMP --
Horn output HORN With a certain ON-OFF operation, the horn relay can be operated.
B
Auto Active Test EKS0064G
DESCRIPTION
q In auto active test mode, operation inspection can be performed when IPDM E/R sends a drive signal to C
the following systems:
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo