Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Quest 2004-2009 Approved Nissan Quest 2005 EX
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download EX documenatation <<
Text preview - extract from the document
B ENGINE
A
EX
SECTION
EXHAUST SYSTEM C
D
E
CONTENTS
PREPARATION .......................................................... 2
. Checking Exhaust System ....................................... 3
. F
Special Service Tool ................................................ 2
. Removal and Installation ......................................... 3
.
Commercial Service Tools ....................................... 2
. REMOVAL ............................................................ 5
.
EXHAUST SYSTEM .................................................. 3
. INSTALLATION .................................................... 5
. G
INSPECTION AFTER INSTALLATION ................. 5 .
H
I
J
K
L
M
Revision: September 2004 EX-1 2005 Quest
PREPARATION
PREPARATION PFP:00002
Special Service Tool EBS00GJ9
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number Description
(Kent-Moore No.)
Tool name
KV10114400 Loosening or tightening heated oxygen sen-
(J-38365) sors:
Heated oxygen sensor wrench a: 22 mm (0.87 in)
S-NT636
Commercial Service Tools EBS00GJA
(Kent-Moore No.) Description
Tool name
(J-43897-18) Reconditioning the exhaust system threads
(J-43897-12) before installing a new heated oxygen sensor
Oxygen sensor thread cleaner (Use with anti-seize lubricant shown below):
a: J-43897-18 (18 mm dia , 0.71 in) for zirco-
nia heated oxygen sensor.
b: J-43897-12 (12 mm dia., 0.49 in) for tita-
nia heated oxygen sensor.
AEM488
Anti-seize lubricant (Permatex 133AR Lubricating oxygen sensor thread cleaning
or equivalent meeting MIL specifica- tool when reconditioning exhaust system
tion MIL-A-907) threads.
AEM489
Power tool Loosening nuts and bolts.
PBIC0190E
Revision: September 2004 EX-2 2005 Quest
EXHAUST SYSTEM
EXHAUST SYSTEM PFP:20100
A
Checking Exhaust System EBS00GJB
Check the exhaust pipes, muffler, and mounting components for
incorrect attachment, leaks, cracks, damage, or deterioration. EX
C
D
SMA211A
E
Removal and Installation EBS00GJC
WARNING:
q Perform the procedures with the exhaust system fully cooled down to avoid injury from the hot F
exhaust system.
q Be careful not to cut your hand on the insulator edge.
NOTE: G
Use genuine NISSAN exhaust system parts or equivalent, which are specifically designed for heat resistance,
corrosion resistance, and shape.
H
I
J
K
L
M
Revision: September 2004 EX-3 2005 Quest
EXHAUST SYSTEM
WBIA0496E
1. Rear muffler hanger 2. Rear muffler 3. U clamp
4. Center exhaust tube hanger 5. Center exhaust tube hanger bracket 6. Center exhaust tube
7. Gasket 8. Front exhaust tube 9. Ring gasket
10. Heated oxygen sensor 2 (bank 2) (5 A/T 11. Front exhaust tube bracket (4 A/T 12. Front exhaust tube hanger bracket
models) models)
13. Main muffler hanger 14. Main muffler
Revision: September 2004 EX-4 2005 Quest
EXHAUST SYSTEM
REMOVAL
Remove exhaust system components using power tool. A
INSTALLATION
Installation is in the reverse order of removal. EX
Tool number : -- (J-43897-12)
Tool number : -- (J-43897-18)
C
CAUTION:
q Always replace exhaust gaskets with new ones when reassembling.
q Before installing a new heated oxygen sensor, clean the exhaust tube threads using commercial
service tool and approved anti-seize lubricant. D
q Discard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; install a new one.
q Do not over-torque the heated oxygen sensor. Doing so may damage the heated oxygen sensor, E
resulting in the MIL coming on.
q If any mounting insulator is badly deformed, repair or replace it. If deposits such as mud pile up on
the mounting insulator, clean and inspect them. F
q Temporarily tighten the nuts on the exhaust manifold side and the bolts on the vehicle side. Check
each part for interference with other components, and then tighten the nuts and bolts to specifica-
tion. G
INSPECTION AFTER INSTALLATION
q With the engine running, check the exhaust tube joints for exhaust gas leaks and unusual noises.
H
q Check that the mounting brackets and mounting insulators are installed properly and free from excessive
stress. Improper installation could result in excessive noise, leaks, and vibration.
I
J
K
L
M
Revision: September 2004 EX-5 2005 Quest
EXHAUST SYSTEM
Revision: September 2004 EX-6 2005 Quest
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo