Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Quest 2004-2009 Approved Nissan Quest 2005 FAX

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document
FAX

>> Download FAX documenatation <<

Text preview - extract from the document

D DRIVELINE/AXLE

B
SECTION
FRONT AXLE C

FAX

E
CONTENTS
PRECAUTIONS ......................................................... 2
. INSPECTION AFTER REMOVAL ........................ 9 . F
Precautions ............................................................. 2
. INSTALLATION .................................................... 9 .
PREPARATION .......................................................... 3
. Removal and Installation (Right Side) ..................... 9 .
Special Service Tools .............................................. 3
. REMOVAL .......................................................... 10
. G
Commercial Service Tools ....................................... 3 . INSPECTION AFTER REMOVAL ...................... 10 .
NOISE, VIBRATION, AND HARSHNESS (NVH) INSTALLATION .................................................. 10 .
TROUBLESHOOTING ............................................... 4 . Disassembly and Assembly (Left Side) ................. 11 .
H
NVH Troubleshooting Chart .................................... 4 . DISASSEMBLY .................................................. 11 .
FRONT WHEEL HUB AND KNUCKLE ..................... 5 . INSPECTION AFTER DISASSEMBLY ............... 13 .
On-Vehicle Inspection and Service ......................... 5 . ASSEMBLY ........................................................ 13.
FRONT WHEEL BEARING .................................. 5 . Disassembly and Assembly (Right Side) ............... 17 . I
Removal and Installation ......................................... 5. DISASSEMBLY .................................................. 17 .
REMOVAL ............................................................ 5
. INSPECTION AFTER DISASSEMBLY ............... 19 .
INSPECTION AFTER REMOVAL ........................ 6 . ASSEMBLY ........................................................ 20. J
INSTALLATION .................................................... 6
. SERVICE DATA AND SPECIFICATIONS (SDS) ..... 23 .
FRONT DRIVE SHAFT .............................................. 8 . Wheel Bearing ....................................................... 23
.
Removal and Installation (Left Side) ....................... 8 . Drive Shaft ............................................................. 23
.
K
REMOVAL ............................................................ 8
. Damper .................................................................. 23
.

Revision: September 2004 FAX-1 2005 Quest
PRECAUTIONS

PRECAUTIONS PFP:00001

Precautions EDS000WC

CAUTION:
q When installing each rubber part, the final tightening must be carried out under unladen condi-
tion* with tires on the ground.
*Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated posi-
tions.
q After installing the removed suspension parts, check the front wheel alignment.
q Do not jack up the vehicle by the transverse link .
Observe the following precautions when disassembling and servicing drive shaft.
q Perform work in a location which is as dust-free as possible.
q Before disassembling and servicing, clean the outside of parts.
q Prevention of the entry of foreign objects must be taken into account during disassembly of the service
location.
q Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a clean
cover must be placed over parts.
q Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint adher-
ing to parts.
q Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be removed by
blowing with air or wiping with paper shop cloths.

Revision: September 2004 FAX-2 2005 Quest
PREPARATION

PREPARATION PFP:00002
A
Special Service Tools EDS000WD

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number Description B
(Kent-Moore No.)
Tool name
C
HT72520000
(J25730-A)
Ball joint remover
Removing outer tie-rod FAX
a: 33 mm (1.30 in)
b: 60 mm (2.36 in)
r: 9 mm (0.35 in)
NT546
E

KV38106700
(J34296) Installing drive shaft
KV38106800 LH: KV38106700 (J34296)
F
(J34297) RH: KV38106800 (J34297)
Differential side oil seal protector
NT147 G

KV40107500 H
( -- ) Removing drive shaft
Drive shaft attachment
I
ZZA1230D

Commercial Service Tools EDS000WE
J
Tool name Description

K
q Removing wheel nuts
Power tool q Removing undercover
q Removing brake caliper assembly L

PBIC0190E

Revision: September 2004 FAX-3 2005 Quest
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING

NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING PFP:00003

NVH Troubleshooting Chart EDS000WF

Use chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.

Refer to DRIVE SHAFT in this chart.
Refer to FRONT AXLE in this chart.
NVH in RAX and RSU sections
FAX-13, FAX-19

FAX-9, FAX-10

FAX-5

WT-3

BR-5

PS-5
--

--
Reference page

REAR AXLE AND REAR SUSPENSION
Improper installation, looseness

Wheel bearing damage
Joint sliding resistance
Excessive joint angle

Possible cause and SUSPECTED PARTS

Parts interference

ROAD WHEEL

DRIVE SHAFT
FRONT AXLE

STEERING
Imbalance

BRAKES
TIRES
DRIVE Noise

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo