Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Quest 2004-2009 Approved Nissan Quest 2006 SB
<< Back |
HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download
Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing.
If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download SB documenatation <<Text preview - extract from the documentH RESTRAINTS
A
B
SECTION
SEAT BELTS C
D
E
CONTENTS
PRECAUTIONS ......................................................... 2
. COMPONENTS .................................................... 8 . F
Precautions for Supplemental Restraint System REMOVAL AND INSTALLATION OF OUT-
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- BOARD SEAT BELT RETRACTOR ..................... 9 .
SIONER" ................................................................. 2
. REMOVAL AND INSTALLATION OF CENTER G
Precaution for Seat Belt Service ............................. 2 . SEAT BELT RETRACTOR ................................... 9 .
AFTER A COLLISION .......................................... 3 . REMOVAL AND INSTALLATION OF SEAT BELT
SEAT BELTS ............................................................. 4
. BUCKLE ............................................................... 9
.
SB
Front Seat Belt ........................................................ 4
. Seat Belt Inspection ............................................... 11
.
COMPONENTS ................................................... 4 . AFTER A COLLISION ........................................ 11 .
REMOVAL AND INSTALLATION OF SEAT BELT PRELIMINARY CHECKS ................................... 11 .
RETRACTOR ....................................................... 5
. SEAT BELT RETRACTOR ON-VEHICLE I
REMOVAL AND INSTALLATION OF SEAT BELT CHECK ............................................................... 12
.
BUCKLE ............................................................... 5
. SEAT BELT RETRACTOR OFF-VEHICLE
Second Row Seat Belt ............................................ 6 . CHECK ............................................................... 12
. J
COMPONENTS ................................................... 6 . LATCH (LOWER ANCHORS AND TETHER FOR
REMOVAL AND INSTALLATION OF SEAT BELT CHILDREN) SYSTEM .............................................. 14 .
RETRACTOR ....................................................... 6
. Removal and Installation ....................................... 14 .
K
REMOVAL AND INSTALLATION OF SEAT BELT TOP TETHER STRAP CHILD RESTRAINT ............ 15 .
BUCKLE ............................................................... 7
. Removal and Installation ....................................... 15 .
Third Row Seat Belt ................................................ 8
.
L
M
Revision: July 2006 SB-1 2006 Quest
PRECAUTIONS
PRECAUTIONS PFP:00001
Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EHS001JB
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
q Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precaution for Seat Belt Service EHS001JC
CAUTION:
q Before removing the seat belt pre-tensioner assembly, turn the ignition switch off, disconnect the
battery ground cable and wait at least 3 minutes.
q Do not use electrical test equipment for seat belt pre-tensioner connector.
q After replacing or reinstalling seat belt pre-tensioner assembly, or reconnecting seat belt pre-ten-
sioner connector, check the system function. Refer to SRS-20, "SRS Operation Check" .
q Do not use disassembled buckle or seat belt assembly.
q Replace anchor bolts if they are deformed or worn out.
q Never oil tongue and buckle.
q If any component of seat belt assembly is questionable, do not repair. Replace the whole seat belt
assembly.
q If webbing is cut, frayed, or damaged, replace seat belt assembly.
q When replacing seat belt assembly, use a genuine NISSAN seat belt assembly.
Revision: July 2006 SB-2 2006 Quest
PRECAUTIONS
AFTER A COLLISION
WARNING: A
Inspect all seat belt assemblies including retractors and attaching hardware after any collision.
NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the col-
lision was minor and the belts show no damage and continue to operate properly. Failure to do so B
could result in serious personal injury in an accident. Seat belt assemblies not in use during a colli-
sion should also be replaced if either damage or improper operation is noted. Seat belt pre-tensioner
should be replaced even if the seat belts are not in use during a frontal collision in which the air bags
are deployed. C
Replace any seat belt assembly (including anchor bolts) if:
q The seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and
buckles show no damage and continue to operate properly). D
q The seat belt was damaged in an accident. (i.e. torn webbing, bent retractor or guide).
q The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage
or distortion and repair as necessary before installing a new seat belt assembly. E
q Anchor bolts are deformed or worn out.
q The seat belt pre-tensioner should be replaced even if the seat belts are not in use during the collision in
which the air bags are deployed. F
G
SB
I
J
K
L
M
Revision: July 2006 SB-3 2006 Quest
SEAT BELTS
SEAT BELTS PFP:86884
Front Seat Belt EHS001JD
COMPONENTS
LHIA0028E
1. Center pillar upper trim 2. Seat belt height adjuster 3. Center pillar
4. Seat belt pre-tensioner connector 5. Seat belt retractor and belt assembly 6. Seat belt buckle
7. Center pillar lower trim 8. Seat belt anchor cover 9. Seat belt guide
10. Assist handle 11. Assist handle bolt covers 12. Center pillar upper bolt cover
Revision: July 2006 SB-4 2006 Quest
SEAT BELTS
REMOVAL AND INSTALLATION OF SEAT BELT RETRACTOR
Removal A
CAUTION:
q Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes. B
1. Remove the center pillar upper/lower trim. Refer to EI-32, "Removal and Installation" .
2. Separate the seat belt guide from the center pillar.
3. Remove the seat belt retractor anchor bolts and assembly. C
q On RH side, disconnect the seat belt tension sensor.
D
E
F
WHIA0183E
G
4. Disconnect the seat belt pre-tensioner connector.
CAUTION:
q For installing/removing seat belt pre-tensioner connec-
SB
tor, insert a thin screwdriver wrapped in tape into the
notch, lift the lock and remove the connector.
q Install the connector with the lock raised, and push the
lock into the connector. I
J
PHIA0341E
Installation
Installation is in the reverse order of removal. K
REMOVAL AND INSTALLATION OF SEAT BELT BUCKLE
Removal L
1. Remove the front seat. Refer to SE-88, "Removal and Installation" .
2. Remove the screws and seat cushion inner finisher.
3. Remove the anchor bolt and buckle. M
LHIA0033E
Installation
Installation is in the reverse order of removal.
Revision: July 2006 SB-5 2006 Quest
SEAT BELTS
Second Row Seat Belt EHS001JE
COMPONENTS
Second Row
LHIA0030E
1. Seat belt height adjuster 2. Seat belt guide 3. Seat belt retractor and belt assembly
4. Seat belt lower anchor 5. D-ring anchor 6. D-ring anchor bolt cover
REMOVAL AND INSTALLATION OF SEAT BELT RETRACTOR
Removal
1. Remove seat belt lower anchor bolt.
2. Remove the D-ring anchor bolt cover and D-ring anchor bolt.
3. Remove the upper luggage area trim. Refer to EI-32, "Removal and Installation" .
4. Remove the seat belt guide bolt.
5. Remove seat belt retractor anchor bolt and the assembly.
Revision: July 2006 SB-6 2006 Quest
SEAT BELTS
6. Remove the height adjuster assembly.
A
Installation
Installation is in the reverse order of removal.
B
REMOVAL AND INSTALLATION OF SEAT BELT BUCKLE
Removal
C
1. Remove the seat back recliner handle.
2. Remove the screws and seat cushion finisher.
3. Remove the seat belt buckle anchor bolt and seat belt buckle. D
E
F
LHIA0033E
Installation G
Installation is in the reverse order of removal.
SB
I
J
K
L
M
Revision: July 2006 SB-7 2006 Quest
SEAT BELTS
Third Row Seat Belt EHS001JF
COMPONENTS
Third Row Outboard
LHIA0029E
1. D-ring mounting bracket 2. Retractor mounting bracket 3. Seat belt retractor and belt assembly
4. Seat belt lower anchor 5. D-ring anchor bolt cover 6. D-ring anchor
Revision: July 2006 SB-8 2006 Quest
SEAT BELTS
Third Row Center
A
B
C
D
E
F
G
SB
LHIA0031E I
REMOVAL AND INSTALLATION OF OUTBOARD SEAT BELT RETRACTOR
Removal
J
1. Remove the upper anchor bolt cover.
2. Remove the D-ring anchor bolt cover and D-ring anchor bolt.
3. Remove the seat belt lower anchor.
K
4. Remove the upper luggage area trim. Refer to EI-32, "Removal and Installation" .
5. Remove the seat belt retractor anchor bolt and retractor assembly.
Installation L
Installation is in the reverse order of removal.
REMOVAL AND INSTALLATION OF CENTER SEAT BELT RETRACTOR M
Removal
1. Remove the upper luggage area trim. Refer to EI-32, "Removal and Installation" .
2. Lower the rear portion of the headliner.
3. Remove the seat belt retractor anchor bolts and retractor assembly.
Installation
Installation is in the reverse order of removal.
REMOVAL AND INSTALLATION OF SEAT BELT BUCKLE
Removal
1. Rotate third row seat assembly rearward to expose underside.
2. Release seat cushion trim cover locking strip.
3. Remove the seat belt buckle anchor bolt and seat belt buckle.
Installation
Installation is in the reverse order of removal.
Revision: July 2006 SB-9 2006 Quest
SEAT BELTS
Seat belt buckle anchor bolt : 49 N
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo