Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Quest 2004-2009 Approved Nissan Quest 2007 FAX

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document
FAX

>> Download FAX documenatation <<

Text preview - extract from the document

D DRIVELINE/AXLE

SECTION FAX FRONT AXLE
B

FAX

E
CONTENTS
PRECAUTIONS ......................................................... 2
. REMOVAL ............................................................ 8
. F
Precautions for Supplemental Restraint System INSPECTION AFTER REMOVAL ........................ 9 .
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- INSTALLATION .................................................... 9 .
SIONER" ................................................................. 2
. Removal and Installation (Right Side) ..................... 9 . G
Precautions ............................................................. 2
. REMOVAL .......................................................... 10
.
PREPARATION .......................................................... 3
. INSPECTION AFTER REMOVAL ...................... 10 .
Special Service Tools .............................................. 3
. INSTALLATION .................................................. 10 .
H
Commercial Service Tools ....................................... 3 . Disassembly and Assembly (Left Side) ................. 11 .
NOISE, VIBRATION, AND HARSHNESS (NVH) DISASSEMBLY .................................................. 11 .
TROUBLESHOOTING ............................................... 4 . INSPECTION AFTER DISASSEMBLY ............... 13 .
NVH Troubleshooting Chart .................................... 4 . ASSEMBLY ........................................................ 13. I
FRONT WHEEL HUB AND KNUCKLE ..................... 5 . Disassembly and Assembly (Right Side) ............... 17 .
On-Vehicle Inspection and Service ......................... 5 . DISASSEMBLY .................................................. 17 .
FRONT WHEEL BEARING .................................. 5 . INSPECTION AFTER DISASSEMBLY ............... 19 . J
Removal and Installation ......................................... 5. ASSEMBLY ........................................................ 20.
REMOVAL ............................................................ 5
. SERVICE DATA AND SPECIFICATIONS (SDS) ..... 23 .
INSPECTION AFTER REMOVAL ........................ 6 . Wheel Bearing ....................................................... 23
.
K
INSTALLATION .................................................... 6
. Drive Shaft ............................................................. 23
.
FRONT DRIVE SHAFT .............................................. 8 . Damper .................................................................. 23
.
Removal and Installation (Left Side) ....................... 8 .
L

Revision: March 2006 FAX-1 2007 Quest
PRECAUTIONS

PRECAUTIONS PFP:00001

Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EDS003AV

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
G To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
G Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
G Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions EDS0034U

CAUTION:
G When installing each rubber part, the final tightening must be carried out under unladen condi-
tion* with tires on the ground.
*Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated posi-
tions.
G After installing the removed suspension parts, check the front wheel alignment.
G Do not jack up the vehicle by the transverse link .
Observe the following precautions when disassembling and servicing drive shaft.
G Perform work in a location which is as dust-free as possible.
G Before disassembling and servicing, clean the outside of parts.
G Prevention of the entry of foreign objects must be taken into account during disassembly of the service
location.
G Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a clean
cover must be placed over parts.
G Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint adher-
ing to parts.
G Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be removed by
blowing with air or wiping with paper shop cloths.

Revision: March 2006 FAX-2 2007 Quest
PREPARATION

PREPARATION PFP:00002
A
Special Service Tools EDS003AT

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number Description B
(Kent-Moore No.)
Tool name
HT72520000 Removing outer tie-rod C
(J-25730-A)
Ball joint remover

FAX

NT146
E
KV38106700 Installing drive shaft
(J-34296) LH: KV38106700 (J-34296)
KV38106800 RH: KV38106800 (J-34297)
(J-34297) F
Differential side oil seal protector

NT147 G
KV40107300 Installing boot bands
( -- )
Boot Band crimping tool H

I
ZZA1229D

KV40107500 Removing drive shaft
( -- ) J
Drive shaft attachment

K
ZZA1230D

Commercial Service Tools EDS003AU L

Tool name Description
Power tool Removing nuts and bolts M

PBIC0190E

Revision: March 2006 FAX-3 2007 Quest
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING

NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING PFP:00003

NVH Troubleshooting Chart EDS0034X

Use chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.

FSU-4, "NVH Troubleshooting Chart"

WT-5, "NVH Troubleshooting Chart"

BR-5, "NVH Troubleshooting Chart"
Refer to DRIVE SHAFT in this chart.

PS-5, "NVH Troubleshooting Chart"
Refer to FRONT AXLE in this chart.
FAX-13, FAX-19

FAX-9, FAX-10

FAX-5

FAX-5
--

--
Reference page

Improper installation, looseness

Wheel bearing damage
Joint sliding resistance
Excessive joint angle

Parts interference
Possible cause and SUSPECTED PARTS

ROAD WHEEL

DRIVE SHAFT
SUSPENSION

FRONT AXLE

STEERING
Imbalance

BRAKES
TIRES
DRIVE Noise

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo