Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Titan 2004-2009 Approved Nissan Titan 2006 DI
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download DI documenatation <<
Text preview - extract from the document
K ELECTRICAL
A
DRIVER INFORMATION SYSTEM
SECTION DI B
C
D
E
CONTENTS
PRECAUTION ........................................................... 3 . Fuel Level Sensor Unit Inspection ......................... 22 . F
Precautions for Supplemental Restraint System FUEL LEVEL SENSOR UNIT ............................ 22 .
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- LOW-FUEL WARNING LAMP ............................ 22 .
SIONER" ................................................................. 3
. Fuel Gauge Fluctuates, Indicates Wrong Value, or G
PREPARATION .......................................................... 4 . Varies ..................................................................... 24
.
Commercial Service Tool ........................................ 4 . Fuel Gauge Does Not Move to Full-position .......... 24 .
COMBINATION METERS .......................................... 5 . Electrical Components Inspection ......................... 25 .
H
System Description ................................................. 5 . FUEL LEVEL SENSOR UNIT CHECK ............... 25 .
UNIFIED METER CONTROL UNIT ..................... 5 . Removal and Installation of Combination Meter .... 25 .
POWER SUPPLY AND GROUND CIRCUIT ....... 6 . COMPASS AND THERMOMETER .......................... 26 .
WATER TEMPERATURE GAUGE ....................... 6 . System Description ................................................ 26 . I
ENGINE OIL PRESSURE GAUGE ...................... 6 . OUTSIDE TEMPERATURE DISPLAY ................ 26 .
A/T OIL TEMPERATURE GAUGE (IF DIRECTION DISPLAY ........................................ 26 .
EQUIPPED) ......................................................... 6 . Wiring Diagram -- COMPAS -- ............................ 27 . J
VOLTAGE GAUGE ............................................... 6 . Trouble Diagnoses ................................................ 28 .
TACHOMETER .................................................... 6 . PRELIMINARY CHECK FOR THERMOMETER 28 ...
FUEL GAUGE ...................................................... 6 . INSPECTION/COMPASS AND THERMOME-
DI
SPEEDOMETER .................................................. 6 . TER .................................................................... 28
.
CAN Communication System Description ............... 7 . Calibration Procedure for Compass ...................... 29 .
Component Parts and Harness Connector Location 7 ..... CORRECTION FUNCTIONS OF COMPASS ..... 29 .
Combination Meter .................................................. 8 . INITIAL CORRECTION PROCEDURE FOR L
CHECK ................................................................. 8
. COMPASS .......................................................... 29 .
Schematic ............................................................... 9
. WARNING LAMPS ................................................... 30 .
Wiring Diagram -- METER -- ............................... 10 . Schematic .............................................................. 30
. M
Terminals and Reference Value for Combination Wiring Diagram -- WARN -- ................................. 31 .
Meter ..................................................................... 12
. Oil Pressure Warning Lamp Stays Off (Ignition
Meter/Gauge Operation and Odo/Trip Meter ........ 13 . Switch ON) ............................................................ 37
.
SELF-DIAGNOSIS FUNCTION ......................... 13 . Oil Pressure Warning Lamp Does Not Turn Off (Oil
HOW TO INITIATE COMBINATION METER Pressure Is Normal) ............................................... 39 .
SELF- DIAGNOSIS MODE ................................ 13 . A/T INDICATOR ....................................................... 40 .
COMBINATION METER SELF-DIAGNOSIS Wiring Diagram -- AT/IND -- ................................ 40 .
MODE FUNCTIONS .......................................... 13 . A/T Indicator Does Not Illuminate .......................... 41 .
How to Proceed With Trouble Diagnosis ............... 17 . WARNING CHIME .................................................... 42 .
Diagnosis Flow ...................................................... 17. Component Parts and Harness Connector Location 42 ...
Power Supply and Ground Circuit Inspection ....... 18 . System Description ................................................ 43 .
Symptom Chart ..................................................... 19 . FUNCTION ......................................................... 43 .
Vehicle Speed Signal Inspection ........................... 19 . IGNITION KEY WARNING CHIME .................... 43 .
Water Temperature Signal Inspection ................... 19 . LIGHT WARNING CHIME .................................. 43 .
Engine Speed Signal Inspection ........................... 19 . SEAT BELT WARNING CHIME .......................... 44 .
Engine Oil Pressure Signal Inspection .................. 20 . CAN Communication System Description ............. 44 .
Revision: October 2006 DI-1 2006 Titan
Wiring Diagram -- CHIME -- ................................ 45 . SONAR BUZZER ................................................60 .
Terminals and Reference Value for BCM ............... 47 . REAR SONAR SENSOR ....................................61 .
Terminals and Reference Value for Combination Wiring Diagram -- SONAR -- ...............................62 .
Meter ..................................................................... 48
. Terminals And Reference Value For Sonar Control
How to Proceed With Trouble Diagnosis ............... 48 . Unit .........................................................................64
.
Preliminary Check ................................................. 49 . How to Proceed With Trouble Diagnosis ...............64 .
INSPECTION FOR POWER SUPPLY AND Pre-diagnosis Inspection ........................................65 .
GROUND CIRCUIT ............................................ 49 . SENSOR STATUS CHECK ................................65 .
CONSULT-II Function (BCM) ................................. 50 . Self-diagnosis Function ..........................................65 .
CONSULT-II BASIC OPERATION PROCEDURE ENTERING DIAGNOSTICS MODE ....................65 .
... 50 REQUESTING NUMBER OF FAULT CODES
DATA MONITOR ................................................. 51 . MODE .................................................................65 .
ACTIVE TEST .................................................... 51 . REQUESTING FAULT CODES MODE ...............66 .
SELF-DIAGNOSTIC RESULTS .......................... 52 . IDLING OR CLEARING FAULT CODES MODE...66
All Warning Chimes Do Not Operate ..................... 52 . Preliminary Check ..................................................67 .
Key Warning Chime and Light Warning Chime Do INSPECTION FOR POWER SUPPLY AND
Not Operate (Seat Belt Warning Chime Does Oper- GROUND CIRCUIT ............................................67 .
ate) ........................................................................ 53
. Symptom Chart ......................................................68 .
Key Warning Chime Does Not Operate ................. 54 . Component Inspection ...........................................69 .
Light Warning Chime Does Not Operate ............... 56 . SONAR BUZZER ................................................69 .
Seat Belt Warning Chime Does Not Operate ........ 57 . REAR SONAR SYSTEM OFF SWITCH .............69 .
REAR SONAR SYSTEM .......................................... 59 . REAR SONAR SYSTEM OFF INDICATOR ........70 .
Component Parts and Harness Connector Location 59 ... Removal and Installation ........................................70 .
System Description ................................................ 60 . REAR SONAR SENSORS ..................................70 .
FUNCTION ......................................................... 60 . SONAR CONTROL UNIT ...................................70 .
REAR SONAR SYSTEM OFF SWITCH ............. 60 .
Revision: October 2006 DI-2 2006 Titan
PRECAUTION
PRECAUTION PFP:00011
A
Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EKS00ACO
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along B
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front C
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING: D
G To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer. E
G Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section. F
G Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
G
H
I
J
DI
L
M
Revision: October 2006 DI-3 2006 Titan
PREPARATION
PREPARATION PFP:00002
Commercial Service Tool EKS00ACQ
Tool name Description
Power tool Loosening bolts and nuts.
PBIC0191E
Revision: October 2006 DI-4 2006 Titan
COMBINATION METERS
COMBINATION METERS PFP:24814
A
System Description EKS00ACR
UNIFIED METER CONTROL UNIT
G Speedometer, odometer, tachometer, fuel gauge, oil pressure gauge, voltage gauge, A/T oil temperature B
gauge (if equipped), and water temperature gauge are controlled by the unified meter control unit, which
is built into the combination meter.
G Warning indicators are controlled by signals drawn from the CAN communication system, and compo-
nents connected directly to the combination meter. C
G Digital meter is adopted for odometer/trip meters*, as well as the A/T position indicator display.
*The record of the odometer is kept even if the battery cable is disconnected.
D
G Odometer/trip meters and A/T indicator segments can be checked in diagnosis mode.
G Meters/gauges can be checked in diagnosis mode.
Illumination control E
The unified meter control unit outputs the speedometer, odometer/trip meters, tachometer, engine oil pressure
gauge, voltage meter, A/T indicator, A/T oil temperature gauge (if equipped), fuel and temperature gauge light-
ing when the ignition switch is turned on. When the headlamp (combination) switch is turned on, the illumina- F
tion control switch can be used to adjust the brightness of the combination meter illumination and the
odometer/trip meters and meter illumination. When the ignition switch is turned from the OFF to the ON posi-
tion, the combination meter dial lighting will remain off for 0.7 seconds. For additional combination meter illu-
mination control information, refer to LT-156, "System Description" . G
H
I
J
DI
L
M
Revision: October 2006 DI-5 2006 Titan
COMBINATION METERS
POWER SUPPLY AND GROUND CIRCUIT
Power is supplied at all times
G through 10A fuse [No.19, located in the fuse block (J/B)]
G to combination meter terminal 8.
With the ignition switch in the ON or START position, power is supplied
G through 10A fuse [No.14, located in the fuse block (J/B)]
G to combination meter terminal 24.
With the ignition switch in the ACC or ON position, power is supplied
G through 10A fuse [No.4, located in the fuse block (J/B)]
G to combination meter terminal 1.
Ground is supplied
G to combination meter terminal 17
G through body grounds M57, M61 and M79.
WATER TEMPERATURE GAUGE
The water temperature gauge indicates the engine coolant temperature.
ECM provides an engine coolant temperature signal to combination meter via CAN communication lines.
ENGINE OIL PRESSURE GAUGE
The engine oil pressure gauge indicates the engine oil pressure.
With the ignition switch in the ON or START position, power is supplied
G through combination meter terminal 22
G to oil pressure sensor terminal 1.
Ground is supplied
G to combination meter terminal 16
G through oil pressure sensor terminal 3.
The combination meter receives the oil pressure signal from oil pressure sensor
G through oil pressure sensor terminal 2
G to combination meter terminal 20.
NOTE:
This gauge is not designed to indicate low oil level. Use the oil level gauge to check the oil level.
A/T OIL TEMPERATURE GAUGE (IF EQUIPPED)
The A/T oil temperature gauge indicates the A/T fluid temperature.
TCM provides a A/T oil temperature signal to combination meter via CAN communication lines.
VOLTAGE GAUGE
The voltage gauge indicates the battery/charging system voltage.
The voltage gauge is regulated by the unified meter control unit.
TACHOMETER
The tachometer indicates engine speed in revolutions per minute (rpm).
ECM provides an engine speed signal to combination meter via CAN communication lines.
FUEL GAUGE
The fuel gauge indicates the approximate fuel level in the fuel tank.
The fuel gauge is regulated by the unified meter control unit and a variable resistor signal supplied
G to combination meter terminal 15
G through fuel level sensor unit and fuel pump terminal 2
G through fuel level sensor unit and fuel pump terminal 5
G from combination meter terminal 16.
SPEEDOMETER
ABS actuator and electric unit (control unit) provides a vehicle speed signal to the combination meter via CAN
communication lines.
Revision: October 2006 DI-6 2006 Titan
COMBINATION METERS
CAN Communication System Description EKS00ACS
A
Refer to LAN-25, "CAN COMMUNICATION" .
Component Parts and Harness Connector Location EKS00ACT
B
C
D
E
F
G
H
I
WKIA4400E
J
1. Fuse block (J/B) 2. Combination meter M24 3. Fuel level sensor unit and fuel pump
C5 (view with fuel tank removed)
4. ECM E16 (view with battery 5. ABS actuator and electric unit (con- 6. Oil pressure sensor F4 DI
removed) trol unit) E125 A. Oil pan (upper)
7. A/T assembly F9
L
M
Revision: October 2006 DI-7 2006 Titan
COMBINATION METERS
Combination Meter EKS00ACU
CHECK
WKIA3855E
Revision: October 2006 DI-8 2006 Titan
COMBINATION METERS
Schematic EKS00ACV
A
B
C
D
E
F
G
H
I
J
DI
L
M
WKWA3707E
Revision: October 2006 DI-9 2006 Titan
COMBINATION METERS
Wiring Diagram -- METER -- EKS00ACW
WKWA3708E
Revision: October 2006 DI-10 2006 Titan
COMBINATION METERS
A
B
C
D
E
F
G
H
I
J
DI
L
M
WKWA3709E
Revision: October 2006 DI-11 2006 Titan
COMBINATION METERS
Terminals and Reference Value for Combination Meter EKS00ACX
Condition
Terminal Wire Reference value (V)
Item Ignition
No. color Operation or condition (Approx.)
switch
Ignition switch ACC or
1 O ACC -- Battery voltage
ON
8 Y/R Battery power supply OFF -- Battery voltage
11 L CAN-H -- -- --
12 P CAN-L -- -- --
Refer to DI-22, "Fuel Level Sensor
15 Y/L Fuel level sensor signal -- --
Unit Inspection" .
Fuel level sensor and oil Refer to DI-22, "Fuel Level Sensor
16 B/P ON --
pressure sensor ground Unit Inspection" .
17 B Ground -- -- 0V
Refer to LT-157, "ILLUMINATION
18 BR Illumination control switch -- Lighting switch ON OPERATION BY LIGHTING
SWITCH" .
Oil pressure sensor sig-
20 Y ON -- 0 - 5V
nal
Oil pressure sensor
22 GR/L ON -- 5V
power supply
Ignition switch ON or
24 O/L ON -- Battery voltage
START
Revision: October 2006 DI-12 2006 Titan
COMBINATION METERS
Meter/Gauge Operation and Odo/Trip Meter EKS00ACY
SELF-DIAGNOSIS FUNCTION A
The following items can be checked during Combination Meter Self-Diagnosis Mode.
G Gauge sweep and present gauge values.
B
G Illuminates all odometer, fuel, and engine temperature segments.
G Illuminates all micro controlled lamps/LEDs regardless of switch configuration.
G Displays estimated present battery voltage.
C
G Displays seat belt buckle switch LH status.
HOW TO INITIATE COMBINATION METER SELF- DIAGNOSIS MODE
NOTE: D
Once entered, Combination Meter Self-Diagnosis Mode will function with the ignition switch in ON or START.
Combination Meter Self-Diagnosis Mode will exit upon turning the ignition switch to OFF or ACC.
To initiate Combination Meter Self-Diagnosis Mode, refer to the following procedure. E
1. Turn the ignition switch ON, while holding the odometer/trip meter switch for 5 - 8 seconds.
NOTE:
If the diagnosis function is activated the odometer/trip meter will display tESt. F
COMBINATION METER SELF-DIAGNOSIS MODE FUNCTIONS
To interpret Combination Meter Self-Diagnosis Mode functions, refer to the following table.
G
Event Odometer Display Description of Test/Data Notes:
Odometer/trip meter A/B
switch held from 5 to 8 H
tESt Initiating self-diagnosis mode
seconds (or until
released)
Return to normal opera-
tion of all lamps/LEDs and I
Odometer/trip meter A/B
displays hex ROM rev. If
switch engaged and
rXXXX, FAIL a ROM checksum fault
released = next test
exists, display alternates J
requested
between "r XXXX" and
"FAIL".
Displays hex ROM rev as
Next test requested nrXXXX DI
stored in NVM.
Bit Coding
7-3 = reserved for future use
2 = TCS/VDC 0 = not present L
Displays 8-bit software
1 = present
Next test requested Sc1XX configuration value in Hex
1 = Shift type 0 = Column shift
format.
1 = Floor shift
0 = ICC 0 = not present M
1 = present
Displays 8-bit software
Bit coding
Next test requested Sc2XX configuration value in Hex
7-0 = Reserved for future use
format.
Bit Coding
7-2 = reserved for future use
Displays 8-bit software 1 = A/T Oil Temp (gauge)
Next test requested EprXX configuration value in Hex 0 = not present
format. 1 = present
1 = Odo Units 0 = kilometers
1 = miles
Displays 8-bit market info $31 = USA
Next test requested 1nFXX
value in Hex format. $2A = Canada
Displays 8-bit engine con-
$08 = 8 cylinder
Next test requested cYLXX figuration value in Hex
$06 = 6 cylinder
format.
Revision: October 2006 DI-13 2006 Titan
COMBINATION METERS
Event Odometer Display Description of Test/Data Notes:
Illuminates all micro-con-
trolled lamps/LEDs
Next test requested bulb
regardless of SW configu-
ration.
Next test requested D-HI Meter/LCD Illumination.
Lights all odometer/trip
meter, fuel, and engine Full daytime brightness all
Next test requested (All segments illuminated)
temperature display seg- LCD segments active
ments.
Next test requested N-HI Meter/LCD Illumination.
Lights all odometer/trip
meter, fuel, and engine Full nighttime brightness all
Next test requested (All segments illuminated)
temperature display seg- LCD segments active
ments.
Next test requested N-LO Meter/LCD Illumination.
Lights all odometer/trip
meter, fuel, and engine Min. nighttime brightness all
Next test requested (All segments illuminated)
temperature display seg- LCD segments active
ments.
Next test requested dS XX Current dimming step. 1-21
Hex EE level. If EE
checksum fault exists,
Next test requested EE XX, FAIL display alternates
between "EE XX" and
"FAIL".
Hex coding of final manu-
Next test requested dtXXXX
facturing test date.
Performs sweep of all
gauges, then displays
Gauges sweep within 10 sec-
Next test requested GAGE present gauge values.
onds
Performs checksum tests
on ROM and EE.
Displays 16-bit fuel flow
Next test requested FFXXXX constant "Q" in tenths of $0000 - $FFFF
cc/min in Hex format.
Displays 16-bit tire factor
Next test requested tF "A" in hundredths in Hex $0000 - $FFFF
format.
Current oil pressure value
Next test requested oP in A/D counts in hex for- $00 - $FF
mat.
Displays oil pressure tell-
Next test requested ot1XX tale "on" threshold in A/D $00 - $FF
counts in Hex format.
Displays oil pressure tell-
Next test requested ot0XX tale "off" threshold in A/D $00 - $FF
counts in Hex format.
Raw uncompensated
Will display "-----" if message is
english speed value in
not received. Will display
Next test requested XXXXX hundredths of MPH.
"99999" if data received is
Speedometer indicates
invalid
present speed.
Raw uncompensated
Will display "-----" if message is
metric speed value in
not received. Will display
Next test requested XXXXX hundredths of KPH.
"99999" if data received is
Speedometer indicates
invalid
present speed.
Revision: October 2006 DI-14 2006 Titan
COMBINATION METERS
Event Odometer Display Description of Test/Data Notes:
A
Tachometer value in
Will display "-----" if message is
Next test requested tXXXX RPM. Tachometer indi-
not received.
cates present RPM.
Present ratioed fuel level 000-009 = Short circuit B
A/D input 1 in decimal for- 010-254 = Normal range
Next test requested F1 XXXX
mat. Fuel gauge indicates 255 = Open circuit
present filtered level. --- = Missing 5 seconds
C
Next test requested F2 XXX Present FLPS. 010-254 normal range
0 = Normal
Next test requested FS X Fuel filter rate
1 = Fast
D
Last temperature gauge
Will display "---"C if message is
input value in degrees C.
not received.
Next test requested XXXC Temperature gauge indi-
Will display "999" if data E
cates present filtered tem-
received is invalid.
perature.
Estimated present bat-
Next test requested BAtXX.X
tery voltage. F
Seat belt buckle switch 0 = Unbuckled
Next test requested rES -X
LH status. 1 = Buckled
Next test requested PA -XX Hex value port A. G
Next test requested Pb -XX Hex value port B.
Next test requested PE -XX Hex value port E.
H
Next test requested PL -XX Hex value port L.
Next test requested P6 -XX Hex value port K.
Next test requested Pn -XX Hex value port M. I
Next test requested PP -XX Hex value port P.
Next test requested PS -XX Hex value port S.
J
Next test requested Pt -XX Hex value port T.
Next test requested Pu -XX Hex value port U.
Next test requested P4 -XX Hex value port V. DI
Next test requested Puu -XX Hex value port W.
A/D port A/D value (non-
Next test requested A00XXX 0-255
ratioed). L
A/D port A/D value (non-
Next test requested A01XXX 0-255
ratioed).
A/D port A/D value (non- M
Next test requested A02XXX 0-255
ratioed).
A/D port A/D value (non-
Next test requested A03XXX 0-255
ratioed).
A/D port A/D value (non-
Next test requested A04XXX 0-255
ratioed).
A/D port A/D value (non-
Next test requested A05XXX 0-255
ratioed).
A/D port A/D value (non-
Next test requested A06XXX 0-255
ratioed).
A/D port A/D value (non-
Next test requested A07XXX 0-255
ratioed).
A/D port A/D value (non-
Next test requested A08XXX 0-255
ratioed).
A/D port A/D value (non-
Next test requested A09XXX 0-255
ratioed).
Revision: October 2006 DI-15 2006 Titan
COMBINATION METERS
Event Odometer Display Description of Test/Data Notes:
A/D port A/D value (non-
Next test requested A10XXX 0-255
ratioed).
A/D port A/D value (non-
Next test requested A11XXX 0-255
ratioed).
A/D port A/D value (non-
Next test requested A12XXX 0-255
ratioed).
A/D port A/D value (non-
Next test requested A13XXX 0-255
ratioed).
A/D port A/D value (non-
Next test requested A14XXX 0-255
ratioed).
A/D port A/D value (non-
Next test requested A15XXX 0-255
ratioed).
Hex value representing
Next test requested PA0-XX
state of A/D ports 0-7.
Hex value representing
Next test requested PA1-XX
state of A/D ports 0-7.
Decimal value of ther-
Next test requested Thr-XXX 0-255
mistor A/D reading.
Return to beginning of self-
Next test requested rXXXX, FAIL
diagnosis.
Revision: October 2006 DI-16 2006 Titan
COMBINATION METERS
How to Proceed With Trouble Diagnosis EKS00ACZ
A
1. Confirm the symptom or customer complaint.
2. Perform diagnosis according to diagnosis flow. Refer to DI-17, "Diagnosis Flow" .
3. According to the symptom chart, repair or replace the cause of the symptom.
B
4. Does the meter operate normally? If so, go to 5. If not, go to 2.
5. Inspection End.
Diagnosis Flow EKS00AD0
C
1. CHECK WARNING INDICATOR ILLUMINATION
1. Turn ignition switch ON. D
2. Make sure warning indicators (such as malfunction indicator lamp and oil pressure low/coolant tempera-
ture high warning indicator) illuminate.
Do warning indicators illuminate? E
YES >> GO TO 2.
NO >> Check ignition power supply system of combination meter. Refer to DI-18, "Power Supply and
Ground Circuit Inspection" . F
2. CHECK SELF-DIAGNOSIS OPERATION OF COMBINATION METER
Perform combination meter self-diagnosis. Refer to DI-13, "SELF-DIAGNOSIS FUNCTION" . G
Does self-diagnosis function operate?
YES >> GO TO 3.
H
NO >> Check combination meter power supply and ground circuit. Refer to DI-18, "Power Supply and
Ground Circuit Inspection" .
3. CHECK ODOMETER OPERATION I
Check segment display status of odometer.
Is the display normal? J
YES >> GO TO 4.
NO >> Replace the combination meter. Refer to IP-13, "COM-
BINATION METER" .
DI
L
WKIA1531E
4. CHECK COMBINATION METER CIRCUIT M
Check indication of each meter/gauge in self-diagnosis mode.
OK or NG
OK >> Go to DI-19, "Symptom Chart" .
NG >> Replace the combination meter. Refer to IP-13, "COM-
BINATION METER" .
WKIA1532E
Revision: October 2006 DI-17 2006 Titan
COMBINATION METERS
Power Supply and Ground Circuit Inspection EKS00AD1
1. CHECK FUSES
Check for blown combination meter fuses.
Unit Power source Fuse No.
Battery 19
Combination meter Ignition switch ON or START 14
Ignition switch ACC or ON 4
Refer to DI-10, "Wiring Diagram -- METER --" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Disconnect combination meter connector.
2. Check voltage between combination meter harness connector
terminals and ground.
Terminals Ignition switch position
(+)
(◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo