Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Titan 2004-2009 Approved Nissan Titan 2007 AP

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download AP documenatation <<

Text preview - extract from the document

I BODY

SECTION
ADJUSTABLE PEDAL
AP B

E
CONTENTS
PRECAUTIONS ......................................................... 2 . Adjustable Pedal (Only Manual Operation Model) 3 ..... F
Precautions for Supplemental Restraint System Pedal Adjusting Control Unit Harness Connector
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Terminal Layout ....................................................... 7
.
SIONER" ................................................................. 2
. Terminals and Reference Values For Pedal Adjust- G
ADJUSTABLE PEDAL SYSTEM .............................. 3 . ing Control Unit ........................................................ 7
.
Automatic Drive Positioner Interlocking Adjustable Trouble Diagnosis .................................................... 7
.
Pedal ....................................................................... 3
. Removal and Installation ....................................... 14 .
H

Revision: August 2006 AP-1 2007 Titan
PRECAUTIONS

PRECAUTIONS PFP:00001

Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EIS004GT

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
G To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
G Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
G Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

Revision: August 2006 AP-2 2007 Titan
ADJUSTABLE PEDAL SYSTEM

ADJUSTABLE PEDAL SYSTEM PFP:98800
A
Automatic Drive Positioner Interlocking Adjustable Pedal EIS007XR

Automatic drive positioner adjustable pedal. Refer to SE-11, "AUTOMATIC DRIVE POSITIONER" .
B
Adjustable Pedal (Only Manual Operation Model) EIS007XS

COMPONENT PARTS AND HARNESS CONNECTOR LOCATION
C

LIIA2437E
K
1. Pedal adjusting control unit M14 2. Pedal adjusting motor E109 3. Pedal adjusting switch M96
(view with steering member
removed LH)
4. A. A/T selector lever 5. A/T device (column shift) M68 L
B. A/T device (floor shift) M203

SYSTEM DESCRIPTION
M
The adjustable pedal system power supply is controlled by pedal adjusting control unit.
Power is supplied at all times
G through 50A fusible link (letter f , located in the fuse and fusible link box)
G to circuit breaker-2 terminal 2
G through circuit breaker-2 terminal 1
G to pedal adjusting control unit terminal 5 and
G through 10A fuse [No. 19, located in the fuse block (J/B)]
G to key switch and key lock solenoid terminal 3 (with floor shift).
With the ignition switch in ON or START position, power is supplied
G through 10A fuse [No. 12, located in the fuse block (J/B)],
G to pedal adjusting control unit terminal 4.
Ground is supplied
G to pedal adjusting switch terminal 4 and
G to pedal adjusting control unit terminal 1
G through body grounds M57, M61 and M79.

Revision: August 2006 AP-3 2007 Titan
ADJUSTABLE PEDAL SYSTEM

Column Shift
When the A/T selector lever is in P position, ground is supplied
G to pedal adjusting control unit terminal 3
G through A/T device terminal 8
G through A/T device terminal 1
G through body grounds M57, M61 and M79.
Floor Shift
When the A/T selector lever is in P position and key is inserted in ignition key cylinder, power is supplied
G to pedal adjusting control unit terminal 3
G through A/T device terminal 6
G through A/T device terminal 5
G from key switch and key lock solenoid terminal 4.
Then pedal adjusting control unit recognizes that A/T selector lever is in P position.
With the ignition switch in OFF or ON position and A/T selector lever is shifted to the P position, power is sup-
plied
G through pedal adjusting control unit terminal 7
G to pedal adjusting switch terminal 1.
With power supplied, pedal adjusting switch is energized.
When pedal is adjusted forward, power is supplied
G through pedal adjusting switch terminal 3
G to pedal adjusting motor terminal +.
Ground is supplied
G to pedal adjusting motor terminal -
G through pedal adjusting switch terminal 2
G through pedal adjusting switch terminal 4
G through body grounds M57, M61 and M79.
With power and ground supplied, accelerator and brake pedals move forward.
When pedal is adjusted backward, power is supplied
G through pedal adjusting switch terminal 2
G to pedal adjusting motor terminal -.
Ground is supplied
G to pedal adjusting motor terminal +
G through pedal adjusting switch terminal 3
G through pedal adjusting switch terminal 4
G through body grounds M57, M61 and M79.
With power and ground supplied, accelerator and brake pedals move backward.

Revision: August 2006 AP-4 2007 Titan
ADJUSTABLE PEDAL SYSTEM

WIRING DIAGRAM -- PEDAL --
A

WIWA1390E

Revision: August 2006 AP-5 2007 Titan
ADJUSTABLE PEDAL SYSTEM

WIWA1391E

Revision: August 2006 AP-6 2007 Titan
ADJUSTABLE PEDAL SYSTEM

Pedal Adjusting Control Unit Harness Connector Terminal Layout EIS00A3M

LIIA2452E D

Terminals and Reference Values For Pedal Adjusting Control Unit EIS00A3N

Wire Voltage (V) E
Terminal Item Conditon
Color (Approx.)
1 B Ground -- 0
A/T selector lever in other than P position 0 F
3 L/R Detent switch (key) signal Key inserted in key switch (floor shift)
Battery voltage
and A/T selector lever in P position
G
4 G/R Ignition switch (ON or START) Ignition switch (ON or START position) Battery voltage
5 L/B Battery power supply -- Battery voltage
Ignition switch ON H
0
A/T selector lever in other than P position
Pedal adjusting switch power supply out-
7 W/R Ignition switch ON
put
Key inserted in key switch (floor shift) Battery voltage
and A/T selector lever in P position
AP

Trouble Diagnosis EIS007XT

WORK FLOW J
1. Check the symptom and customer's requests.
2. Perform the preliminary check. Refer to AP-7, "PRELIMINARY CHECK" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to AP-7, K
"TROUBLE DIAGNOSIS CHART BY SYMPTOM" .
4. Does adjustable pedal system operate normally?
YES: GO TO 5. L
NO: GO TO 3.
5. Inspection End.
PRELIMINARY CHECK M

1. CHECK ADJUSTABLE PEDAL MECHANISM
Check the following.
G Movable part of accelerator pedal or brake pedal is deformed, or there is foreign material in it.
G Accelerator pedal or brake pedal is deformed or broken.
OK or NG
OK >> Preliminary check is OK.
NG >> Repair the malfunctioning part and check again.
TROUBLE DIAGNOSIS CHART BY SYMPTOM
NOTE:
Always check the WORK FLOW before troubleshooting. Refer to AP-7, "WORK FLOW" .

Revision: August 2006 AP-7 2007 Titan
ADJUSTABLE PEDAL SYSTEM

Symptom Diagnosis/ service procedure Reference page
1. Pedal adjusting control unit power supply and ground circuit
AP-8
inspection.
Adjustable pedal system does not operate. 2. Pedal adjusting switch power supply and ground circuit inspec-
AP-11or AP-12
tion.
3. Pedal adjusting motor circuit inspection. AP-13
1. A/T device (park position switch) circuit inspection. AP-9 or AP-10
Adjustable pedal system does operate when
ignition switch is turned ON and A/T selector 2. Pedal adjusting control unit signal inspection. AP-8
lever is in other than P position.
3. Replace pedal adjusting control unit. --
Adjustable pedal system does not operate
when ignition switch is turned ON and A/T 1. A/T device (park position switch) circuit inspection. AP-10
selector lever is in P position.

PEDAL ADJUSTING CONTROL UNIT IGNITION SIGNAL INSPECTION
1. CHECK FUSE
Check 10A fuse [No. 12, located in fuse block (J/B)].
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.

2. CHECK PEDAL ADJUSTING CONTROL UNIT IGNITION POWER SUPPLY CIRCUIT
1. Disconnect pedal adjusting control unit.
2. Check voltage between pedal adjusting control unit connector
and ground.
Terminals Voltage (V)
Connector Condition
(+) (-) (Approx.)

Ignition switch ON Battery voltage
M14 4 Ground
Ignition switch OFF 0

OK or NG
OK >> Pedal adjusting control unit ignition signal is OK. LIIA0885E

NG >> Repair or replace harness.
PEDAL ADJUSTING CONTROL UNIT POWER SUPPLY AND GROUND INSPECTION
1. CHECK PEDAL ADJUSTING CONTROL UNIT OUTPUT POWER SUPPLY
1. Turn ignition switch OFF.
2. Check voltage between pedal adjusting control unit connector
M14 terminal 7 and ground.
7 - Ground : Battery voltage
OK or NG
OK >> Pedal adjusting control unit power supply and ground is
OK.
NG >> GO TO 2.
LIIA0886E

Revision: August 2006 AP-8 2007 Titan
ADJUSTABLE PEDAL SYSTEM

2. CHECK PEDAL ADJUSTING CONTROL UNIT POWER SUPPLY CIRCUIT A
1. Disconnect pedal adjusting control unit.
2. Check voltage between pedal adjusting control unit connector
M14 terminal 5 and ground. B

5 - Ground : Battery voltage
OK or NG C
OK >> GO TO 3.
NG >> Repair or replace harness.
D
LIIA0887E

3. CHECK PEDAL ADJUSTING CONTROL UNIT GROUND CIRCUIT E

Check continuity between pedal adjusting control unit connector
M14 terminal 1 and ground.
F
1 - Ground : Continuity should exist.
OK or NG
OK >> Replace pedal adjusting control unit. G
NG >> Repair or replace harness.

LIIA0888E

A/T DEVICE (PARK POSITION SWITCH) CIRCUIT INSPECTION (FLOOR SHIFT) AP
1. CHECK PEDAL ADJUSTING CONTROL UNIT INPUT SIGNAL
1. Turn ignition switch OFF. J
2. Disconnect pedal adjusting control unit.
3. With key inserted in ignition cylinder, check voltage between
pedal adjusting control unit connector and ground. K

Terminals Voltage (V)
Connector Condition
(+) (-) (Approx.)
L
P position Battery voltage
M14 3 Ground
Other than P position 0
M
OK or NG LIIA2155E

OK >> A/T device circuit is OK.
NG >> GO TO 2.

2. CHECK A/T DEVICE POWER SUPPLY CIRCUIT
1. Disconnect A/T device.
2. With key inserted, check voltage between A/T device connector
M203 terminal 5 and ground.
5 - Ground : Battery voltage
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.

LIIA2156E

Revision: August 2006 AP-9 2007 Titan
ADJUSTABLE PEDAL SYSTEM

3. CHECK A/T DEVICE HARNESS
1. Disconnect pedal adjusting control unit.
2. Check continuity between pedal adjusting control unit connector
M14 terminal 3 and A/T device connector M203 terminal 6.
3-6 : Continuity should exist.
3. Check continuity between pedal adjusting control unit connector
M14 terminal 3 and ground.
3 - Ground : Continuity should not exist.
OK or NG
LIIA0990E
OK >> GO TO 4.
NG >> Repair or replace harness.

4. CHECK A/T DEVICE
Check continuity between A/T device terminals as follows.
Terminals Condition Continuity
P position Yes
5 6
Other than P position No

OK or NG
OK >> Inspect shift lock system. Refer to AT-234, "A/T SHIFT
LOCK SYSTEM" .
NG >> Replace control device assembly. Refer to AT-234, "A/T
SHIFT LOCK SYSTEM" . LIIA2438E

A/T DEVICE (PARK POSITION SWITCH) CIRCUIT INSPECTION (COLUMN SHIFT)
1. CHECK PEDAL ADJUSTING CONTROL UNIT INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect pedal adjusting control unit.
3. Check continuity between pedal adjusting control unit connector
and ground.
Connector Terminals Condition Continuity
P position Yes
M14 3 Ground
Other than P position No

OK or NG
OK >> A/T device circuit is OK. LIIA2157E

NG >> GO TO 2.

2. CHECK A/T DEVICE GROUND CIRCUIT
1. Disconnect A/T device.
2. Check continuity between A/T device connector M68 terminal 1
and ground.
1 - Ground : Continuity should exist.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.

LIIA2158E

Revision: August 2006 AP-10 2007 Titan
ADJUSTABLE PEDAL SYSTEM

3. CHECK A/T DEVICE HARNESS A
1. Check continuity between pedal adjusting control unit connector
M14 (A) terminal 3 and A/T device connector M68 (B) terminal
8. B
3-8 : Continuity should exist.
2. Check continuity between pedal adjusting control unit connector
C
M14 (A) terminal 3 and ground.
3 - Ground : Continuity should not exist.
OK or NG D
OK >> GO TO 4. LIIA2159E

NG >> Repair or replace harness.
E
4. CHECK A/T DEVICE
Check continuity between A/T device terminals as follows.
F
Terminals Condition Continuity
P position Yes
1 8 G
Other than P position No

OK or NG
OK >> Inspect shift lock system. Refer to AT-234, "A/T SHIFT H
LOCK SYSTEM" .
NG >> Replace column shift control device. Refer to AT-234,
"A/T SHIFT LOCK SYSTEM" . LIIA1993E
AP
PEDAL ADJUSTING SWITCH POWER SUPPLY AND GROUND INSPECTION (FLOOR SHIFT)
1. CHECK PEDAL ADJUSTING SWITCH POWER SUPPLY J
1. Turn ignition switch OFF, leave key in ignition cylinder.
2. Disconnect pedal adjusting switch.
3. Check voltage between pedal adjusting switch connector M96 K
terminal 1 and ground.
Terminals Voltage (V) L
Connector Condition
(+) (-) (Approx.)

P position Battery voltage
M96 1 Ground
Other than P position 0 M
OK or NG LIIA0894E

OK >> GO TO 3.
NG >> GO TO 2.

Revision: August 2006 AP-11 2007 Titan
ADJUSTABLE PEDAL SYSTEM

2. CHECK PEDAL ADJUSTING SWITCH HARNESS
1. Disconnect pedal adjusting control unit.
2. Check continuity between pedal adjusting control unit connector
M14 terminal 7 and pedal adjusting switch connector M96 termi-
nal 1.
7-1 : Continuity should exist.
3. Check continuity between pedal adjusting control unit connector
M14 terminal 7 and ground.
7 - Ground : Continuity should not exist.
OK or NG LIIA0895E

OK >> Check the condition of the harness and connector.
NG >> Repair or replace harness.

3. CHECK PEDAL ADJUSTING SWITCH GROUND CIRCUIT
Check continuity between pedal adjusting switch connector M96 ter-
minal 4 and ground.
4 - Ground : Continuity should exist.
OK or NG
OK >> Replace pedal adjusting switch.
NG >> Repair or replace harness.

LIIA0896E

PEDAL ADJUSTING SWITCH POWER SUPPLY AND GROUND INSPECTION (COLUMN SHIFT)
1. CHECK PEDAL ADJUSTING SWITCH POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect pedal adjusting switch.
3. Check voltage between pedal adjusting switch connector M96
terminal 1 and ground.
1 - Ground : Battery voltage
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.
LIIA0894E

Revision: August 2006 AP-12 2007 Titan
ADJUSTABLE PEDAL SYSTEM

2. CHECK PEDAL ADJUSTING SWITCH HARNESS A
1. Disconnect pedal adjusting control unit.
2. Check continuity between pedal adjusting control unit connector
M14 terminal 7 and pedal adjusting switch connector M96 termi- B
nal 1.
7-1 : Continuity should exist.
C
3. Check continuity between pedal adjusting control unit connector
M14 terminal 7 and ground.
7 - Ground : Continuity should not exist. D
OK or NG LIIA0895E

OK >> Check the condition of the harness and connector.
NG >> Repair or replace harness. E

3. CHECK PEDAL ADJUSTING SWITCH GROUND CIRCUIT
F
Check continuity between pedal adjusting switch connector M96 ter-
minal 4 and ground.
4 - Ground : Continuity should exist. G
OK or NG
OK >> Replace pedal adjusting switch.
NG >> Repair or replace harness. H

AP
LIIA0896E

PEDAL ADJUSTING MOTOR CIRCUIT INSPECTION
J
1. CHECK PEDAL ADJUSTING SWITCH
1. Turn ignition switch OFF.
2. Disconnect pedal adjusting switch. K
3. Check continuity between pedal adjusting switch terminals as
follows.
L
Terminals Condition Continuity
Pedal adjusting switch forward. Yes
1
Pedal adjusting switch neutral. No M
3
Pedal adjusting switch backward. Yes
4
Pedal adjusting switch neutral. No LIIA0897E

Pedal adjusting switch backward. Yes
1
Pedal adjusting switch neutral. No
2
Pedal adjusting switch forward. Yes
4
Pedal adjusting switch neutral. No

OK or NG
OK >> GO TO 2.
NG >> Replace pedal adjusting switch.

Revision: August 2006 AP-13 2007 Titan
ADJUSTABLE PEDAL SYSTEM

2. CHECK PEDAL ADJUSTING MOTOR HARNESS
1. Disconnect pedal adjusting motor.
2. Check continuity between pedal adjusting switch connector M96
terminals 2, 3 and pedal adjusting motor connector E109 termi-
nals +, -.
2-- : Continuity should exist.
3-+ : Continuity should exist.
3. Check continuity between pedal adjusting switch connector M96
terminals 2, 3 and ground.
2 - Ground : Continuity should not exist. LIIA1319E

3 - Ground : Continuity should not exist.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.

3. CHECK PEDAL ADJUSTING MOTOR POWER SUPPLY
1. Connect pedal adjusting switch.
2. Check voltage between pedal adjusting motor and ground.

Connector Terminals Voltage (V)
Condition
(+) (-) (Approx.)

Pedal adjusting switch
Battery voltage
+ forward
Other than above 0
M14 Ground
Pedal adjusting switch
Battery voltage
- backward LIIA1320E

Other than above 0

OK or NG
OK >> Replace pedal adjusting motor. Refer to AP-14, "Removal and Installation" .
NG >> Repair or replace harness.
Removal and Installation EIS007XU

Refer to ACC-3, "ACCELERATOR CONTROL SYSTEM" and BR-6, "BRAKE PEDAL" .

Revision: August 2006 AP-14 2007 Titan

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo