
TRANSMISSION & DRIVELINE
A
SECTION RAX REAR AXLE
B
C
RAX
E
CONTENTS
PRECAUTION .............................................. 2
. On-Vehicle Inspection ............................................. 5
. F
PRECAUTIONS .................................................. 2
. REMOVAL AND INSTALLATION ............... 6
.
Precaution ................................................................ 2
. G
AXLE OIL SEAL ................................................. 6
PREPARATION ........................................... 3
. Removal and Installation ......................................... 6
.
PREPARATION .................................................. 3
. AXLE BEARING ................................................. 7 H
Special Service Tool ................................................ 3
. Removal and Installation ......................................... 7
.
Commercial Service Tool ......................................... 3
.
AXLE SHAFT ..................................................... 8
Removal and Installation ......................................... 8
. I
SYMPTOM DIAGNOSIS .............................. 4
.
NOISE, VIBRATION, AND HARSHNESS SERVICE DATA AND SPECIFICATIONS
(NVH) TROUBLESHOOTING ............................ 4
. (SDS) ........................................................... 12
. J
NVH Troubleshooting Chart ..................................... 4
.
SERVICE DATA AND SPECIFICATIONS
BASIC INSPECTION ................................... 5
. (SDS) ................................................................. 12
K
Axle Bearing ...........................................................12
.
AXLE SHAFT ..................................................... 5
.
L
M
N
O
P
Revision: April 2007 RAX-1 2008 Titan
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution INFOID:0000000001337996
When installing rubber parts, final tightening must be carried out under unladen condition* with tires
on ground.
* Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated posi-
tions.
Revision: April 2007 RAX-2 2008 Titan
PREPARATION
< PREPARATION >
PREPARATION A
PREPARATION
Special Service Tool INFOID:0000000001337997
B
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number Description
(Kent-Moore No.) C
Tool name
KV40101000 Removing axle shaft
(J-25604-01) RAX
Axle stand
E
NT159
ST36230000 Removing axle shaft F
(J-25840-A)
Slide hammer
G
NT126
H
ST30031000 Removing axle shaft bearing
( -- )
Bearing splitter I
J
ZZA0700D
Commercial Service Tool INFOID:0000000001337998 K
Tool name Description L
Power tools Removing and installing nuts and bolts
M
N
PBIC0190E
O
P
Revision: April 2007 RAX-3 2008 Titan
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart INFOID:0000000001337999
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
DLN-139 (2S1410), DLN-148 (3S1350),
DLN-122 (2F1310), DLN-130 (2S1350),
DLN-204, "NVH Troubleshooting Chart"
RSU-4, "NVH Troubleshooting Chart"
WT-31, "NVH Troubleshooting Chart"
WT-31, "NVH Troubleshooting Chart"
BR-5, "NVH Troubleshooting Chart"
DLN-157, (3S1410)
RAX-8
RAX-5
RAX-5
Reference page
Improper installation, looseness
Wheel bearing damage
PROPELLER SHAFT
REAR FINAL DRIVE
Parts interference
Possible cause and SUSPECTED PARTS
ROAD WHEEL
SUSPENSION
BRAKES
TIRES
Noise