Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan Versa 2007-2009 Approved Nissan Versa 2007 IP

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download IP documenatation <<

Text preview - extract from the document

I BODY

INSTRUMENT PANEL
SECTION IP B

E
CONTENTS
PRECAUTIONS ......................................................... 2
. TRUNK ................................................................. 7
. F
Precautions for Supplemental Restraint System SUNROOF/HEADLINING .................................... 7 .
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- OVERHEAD CONSOLE (FRONT AND REAR)..... 7
SIONER" ................................................................. 2
. SEATS .................................................................. 7
. G
Precautions ............................................................. 2
. UNDERHOOD ...................................................... 7 .
PREPARATION .......................................................... 3
. Diagnostic Worksheet .............................................. 8
.
Special Service Tools .............................................. 3
. INSTRUMENT PANEL ASSEMBLY ........................ 10 .
H
Commercial Service Tools ....................................... 3 . Component Parts ................................................... 10
.
SQUEAK AND RATTLE TROUBLE DIAGNOSES..... 4 Removal and Installation ....................................... 11 .
Work Flow ............................................................... 4
. WORK STEPS ................................................... 11 .
CUSTOMER INTERVIEW .................................... 4 . INSTRUMENT PANEL ASSEMBLY ................... 12 . IP
DUPLICATE THE NOISE AND TEST DRIVE ...... 5 . CLUSTER LID A ................................................. 16 .
CHECK RELATED SERVICE BULLETINS .......... 5 . CLUSTER LID C ................................................ 18 .
LOCATE THE NOISE AND IDENTIFY THE COMBINATION METER ..................................... 19 . J
ROOT CAUSE ..................................................... 5. GLOVE BOX ASSEMBLY .................................. 21 .
REPAIR THE CAUSE .......................................... 5 . INSTRUMENT LOWER FINISHER .................... 21 .
CONFIRM THE REPAIR ...................................... 6 . CENTER CONSOLE ASSEMBLY ...................... 22 .
K
Generic Squeak and Rattle Troubleshooting .......... 6 . Disassembly and Assembly ................................... 24 .
INSTRUMENT PANEL ......................................... 6 . GLOVE BOX ASSEMBLY .................................. 24 .
CENTER CONSOLE ............................................ 6 . CENTER CONSOLE ASSEMBLY ...................... 25 .
DOORS ................................................................ 6
. COMBINATION METER ..................................... 25 . L

Revision: June 2006 IP-1 2007 Versa
PRECAUTIONS

PRECAUTIONS PFP:00001

Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT PRE-TENSIONER" EIS009AU

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
G To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
G Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
G Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions EIS00972

G Disconnect both battery terminals in advance.
G Disconnect air bag system line in advance.
G Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
G Be careful not to scratch pad and other parts.
G When removing or disassembling any part, be careful not to damage or deform it. Protect parts which may
get in the way with cloth.
G When removing parts, protect parts by wrapping tools with vinyl or tape.
G Keep removed parts protected with cloth.
G If a clip is deformed or damaged, replace it.
G If an non-reusable part is removed, replace it with a new one.
G Tighten bolts and nuts firmly to the specified torque.
G After re-assembly has been completed, make sure each part functions correctly.
G Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
G Do not use any organic solvent, such as thinner or benzine.

Revision: June 2006 IP-2 2007 Versa
PREPARATION

PREPARATION PFP:00002
A
Special Service Tools EIS00973

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number B
(Kent-Moore No.) Description
Tool name
-- Locating the noise C
(J-39570)
Chassis ear

SIIA0993E
E
-- Repairing the cause of noise
(J-43980)
NISSAN Squeak and Rattle
Kit F

SIIA0994E G

Commercial Service Tools EIS00974

Tool name Description H
Engine ear Locating the noise

J
SIIA0995E

Power tool Loosening bolts and nuts
K

PBIC0191E

Revision: June 2006 IP-3 2007 Versa
SQUEAK AND RATTLE TROUBLE DIAGNOSES

SQUEAK AND RATTLE TROUBLE DIAGNOSES PFP:00000

Work Flow EIS009AV

SBT842

CUSTOMER INTERVIEW
Interview the customer, if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer's comments; refer to IP-8, "Diagnostic Worksheet" . This information is necessary to duplicate the
conditions that exist when the noise occurs.
G The customer may not be able to provide a detailed description or the location of the noise. Attempt to
obtain all the facts and conditions that exist when the noise occurs (or does not occur).
G If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that the customer
is concerned about. This can be accomplished by test driving the vehicle with the customer.
G After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.

◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo